Farklı elektrik direnç kaynağı parametrelerinin mukavemet üzerine etkilerinin incelenmesi
Bu çalışmada otomotiv endüstrisinde kullanılan 5000 serisi alüminyum alaşımlarından olan Al 5754- H111 malzemesi elektrik direnç kaynak yöntemi ile farklı kaynak akımı, kaynak süresi ve sıkıştırma yükü ile birleştirilmişlerdir. Kaynak işlemi uygulanmış numunelerin mekanik özelliklerini belirlemek amacıyla kaynaklı bağlantılara çekme deneyi yapılmıştır. Test sonuçlarına göre elde edilen çekme mukavemeti ve çekme uzaması değerlerindeki farklılıklar, kaynak parametrelerindeki değişimin kaynağın mekanik özellikleri üzerinde önemli etkiye sahip olduğunu göstermiştir.
Investigation of the effects of different electrical resistance welding parameters on strength
In this study, Al 5754-H111 material from 5000 series aluminum alloys used in the automotive industry were combined with different welding current, welding time and compression load by electrical resistance welding method. Tensile tests were performed to determine the mechanical properties of welded specimens. The differences in tensile strength and tensile elongation values obtained from the test results have shown that the variation in weld parameters has a significant effect on the mechanical properties of the weld.
___
- E. Doruk, M. Pakdil, G.Çam, I. Durgun, U.
C. Kumru,“Otomotiv sektöründe direnç
nokta kaynağı Tofaş uygulamaları,” Kaynak
Teknolojisi IX. Ulusal Kongre ve Sergisi,
pp. 29–38, 2015.
- N. Ferudun, “Akım ve basıncın direnç
kaynak kalitesine etkisi,” Metalurji Dergisi,
vol. 175, pp. 32–34, 2015
- YB. Demir, E. İncekar, Ö. Dincel and M.
Elitaş, “İleri Dayanımlı Çeliklerde Nokta
Direnç Kaynağı Etkilerinin İncelenmesi,”
El-Cezerî Journal of Science and
Engineering, vol. 4, no. 1, pp. 92–100,
2017.
- M. Sun, S. T. Niknejad, G. Zhang, M. K.
Lee, L. Wu and Y. Zhou, “Microstructure
and mechanical properties of resistance spot
welded AZ31/AA5754 using a nickel
interlayer,” Materials and Design, vol. 87,
pp. 905–913, 2015.
- N. Chen, H.-P.Wang, B. E. Carlson, D. R.
Sigler and M. Wang, “Fracture mechanisms
of Al/steel resistance spot welds in lap
shear test,” Journal of Materials Processing
Technology, vol. 243, pp. 347–354, 2017.
- J. Chen, X. Yuan, Z. Hu, C. Sun, Y. Zhang
and Y. Zhang, “Microstructure and
mechanical properties of resistance-spotwelded
joints for A5052 aluminum alloy
and DP 600 steel,” Materials
Characterization, vol. 120, pp. 45–52,
2016.
- D. Sun, Y. Zhang, Y. Liu, X. Gu and H. Li,
“Microstructures and mechanical properties
of resistance spot welded joints of 16Mn
steel and 6063-T6 aluminum alloy with
different electrodes,” Materials and Design,
vol. 109, pp. 596–608, 2016.
- Y. Kaya and N. Kahraman, “Titanyum
sacların nokta direnç kaynağı ile
birleştirilmesinde kaynak parametrelerinin
çekirdek oluşumuna etkisi,” Journal of
Polytechnic, vol. 14, no. 4, pp. 263–270,
2011.
- S. Aslanlar, A. Ogur, U. Ozsarac and E.
Ilhan, “Welding time effect on mechanical
properties of automotive sheets in electrical
resistance spot welding,” Materials and
Design, vol. 29, pp. 1427–1431, 2008.
- D. Özyürek, “An effect of weld current and
weld atmosphere on the resistance spot
weldability of 304L austenitic stainless
steel,” Materials and Design, vol. 29, pp.
597–603, 2008.
- D.Q. Sun, B. Lang, D.X. Sun and J.B. Li,
“Microstructures and mechanical properties
of resistance spot welded magnesium alloy
joints,” Materials Science and Engineering
A, vol. 460–461, pp. 494–498, 2007.
- M. Pouranvari, H. R. Asgari, S. M.
Mosavizadch, P. H. Marashi and M.
Goodarzi, “Effect of weld nugget size on
overload failure mode of resistance spot
welds,” Science and Technology of Welding
and Joining, vol. 12, no. 3, pp. 217–225,
2007.
- R.S. Florea, K.N. Solanki, D.J. Bammann,
J.C. Baird, J.B. Jordon and M.P. Castanier,
“Resistance spot welding of 6061-T6
aluminum: Failure loads and deformation,”
Materials and Design, vol. 34, pp. 624–
630, 2012.
- S. Hassanifard and M. Zehsaz, “The effects
of residual stresses on the fatigue life of
5083-O aluminum alloy spot welded
joints,” Procedia Engineering, vol. 2, pp.
1077–1085, 2010.
- A.M. Pereira, J.M. Ferreira, A. Loureiro,
J.D.M. Costa and P.J. Bártolo, “Effect of
process parameters on the strength of
resistance spot welds in 6082-T6
aluminium alloy,” Materials and Design,
vol. 231, pp. 2454–2463, 2010.
- S. Wu, B. Ghaffari, E. Hetrick, M. Li, Z. Jia
and Q. Liu, “Microstructure
characterization and quasi-static failure
behavior of resistance spot welds of
AA6111-T4 aluminum alloy,” Trans.
Nonferrous Met. Soc. China, vol. 24, pp.
3879–3885, 2014.
- L. Han, M. Thornton, D. Li and M.
Shergold, “Effect of governing metal
thickness and stack orientation on weld
quality and mechanical behaviour of
resistance spot welding of AA5754
aluminium,” Materials and Design, vol. 32,
pp. 2107–2114, 2011.
- J. Senkara and H. Zhang, “Cracking in spot
welding aluminum alloy AA5754,”
Welding Journal, vol. 79, pp. 194–201,
2000.
- X. Long and S. K. Khanna, “Residual
stresses in spot welded new generation
aluminium alloys Part B – finite element
simulation of residual stresses in a spot
weld in 5754 aluminium alloy,” Science
and Technology of Welding and Joining,
vol. 10, no.1, pp. 88–94, 2005.
- S. A. Şafak, “Uçak endüstrisinde kullanılan
alüminyum alaşımlarının elektrik direnç
nokta kaynak yöntemi ile birleştirilmesi ve
mekanik özelliklerinin incelenmesi,”
Sakarya Üniversitesi Fen Bilimleri
Enstitüsü, 2011.
- H. Zhang, X. Qiu, F. Xing, J. Bai and J.
Chen, “Failure analysis of dissimilar
thickness resistance spot welded joints in
dual-phase steels during tensile shear test,”
Materials and Design, vol. 55, pp. 366–
372, 2014.
- O. Yıldırım, “Otomotiv Endüstrisinde
Kullanılan Nokta Direnç Kaynak
Uygulamalarında İşlem Parametrelerinin
Etkilerinin İncelenmesi,” Yıldız Teknik
Üniversitesi Fen Bilimleri Enstitüsü, 2010.