CNC TEL EROZYON TEZGAHLARINDA FARKLI MALZEMELERİN İŞLENEBİLİRLİĞİNİN ARAŞTIRILMASI
Bu çalışmada, tel erozyon yönteminde işlem parametrelerinin farklı kesmealanlarına sahip AISI D5 takım çeliği ve alüminyum alaşımının mikroyapıdeğişimi ve yüzey pürüzlülüğüne etkisi incelenmiştir. Kesme işlemlerindevurum süresi, gerilim, sıvı sirkülasyon basıncı ve tel ilerleme hızı değişkenolarak alınırken, tabla ilerleme hızı, tel gerginliği, vurum ara süresi ve telçapı sabit olarak alınmıştır. Deneylerde 0.25mm çapında pirinç telkullanılmıştır. Deneyler sonucunda numunelerin mikroyapıları optik ve SEMmikroskoplarında incelenmiş, mikrosertlik ve yüzey pürüzlülükleriölçülmüştür. Sonuç olarak, farklı özelliklere sahip malzemelerde kesmeişlemi sonrasında yüzey pürüzlülük ve mikroyapı değişimlerinin işlemparametrelerine bağlı olarak değiştiği tespit edilmiştir.
THE INVESTIGATION of MACHINABILITY of DISSIMILAR MATERIALS in CNC WIRE – EDM MACHINES
In this study, the microstructure variation and surfaceroughness according to the cutting parameters were investigated. Inexperiments, pulse-on time, voltage, dielectric fluid circulation pressureand wire feed rate taken as alternative when table feed rate, wiretension, pulse-off time wire diameter were constant. In experimentsbrass wire of 0.25mm diameter were used. In end of cutting operations,the microstructures of specimens were examined by optic and SEMmicroscopy. The micro hardness and surface roughness were measured.It was concluded that the surface roughness and microstructure arechange according to process parameters in end of cutting operations ofthe materials with different properties.
___
- [1] idea.metu.edu.tr/program/aiy.
- [2] K. Shajan, M. Kamal, M.S. Shunmugam., “ Data mining
applied to wire – EDM process” , Journal of Materials
Processing Technology, 142, (2003), 182 – 189.
- [3] Speedding, T. A., Wang, Z. O., Parametric Optimization and
Surface Characterization of Wire Electrical Discharge
Machining Process, Precision Engineering 20: (1997), 5-15.
- [4] Liao, Y.S., Woo, J. C., The Effect of Machining Settings on
the behaviour of Vurume Trains in the WEDM Process,
Journal of Materials Processing Technology 71, (1997), 433-
439.
- [5] M.S. Shunmugam, S. Sai Kumar, I. K. Kaul, “ Fuzzy logic
modelling of wire – cut EDM process” , Proc. SPIE 4192
(2000) 417 – 425.
- [6] M.S. Shunmugan, S. Sai Kumar, I. K. Kaul, “ Modelling of
wire – cut EDM by neural network”, Proc. SPIE 4192 (1999)
185 – 193.
- [7] Robofil 310, Wire EDM of Charmilles Technologies,
Reference manual, vol. 1, 1994.
- [8] Boyer, E. H., Gall, L. T., Nontraditional Machining Processes,
Metals Handbook, Desk Edition, American Society for Metals
Park, Ohio 44073, 1992.
- [9] Guo, Z.N., Lee, T.C., Yue, T.M., and Lau, W.S., 1997, “Study
on the machining mechanism of WEDM with ultrasonic
vibration of the wire”, Journal of Materials Processing
Technology, 69, 212 – 221.
- [10] Gökler. İ, Ozanözgü M, Experimental investigation of effects
cutting parameters on surface roughness in the WEDM
process (2000).
- [11] J. Prohaszka, A.G. Mamalis, N.M. Vaxevanidis, The effects
of electrode material on machinability in wire electro –
discharge machining. Journal of Materials Processing
Technology, 69, 233 – 237, 1996.
- [12] M. Rozenek, J. Kozak, L. Dobrovwki, K. Lubkovwki,
Electrical discharge machining characteristis of metal matrix
composites. Journal of Materials Processing Technology, 109,
367-370, 2001.