Mekanik alaşımlama ile üretilen nanokristal Mg50Cu50 tozları
Bu çalışmada Mg ve Cu ikili karışımı ile nanokristal Mg50Cu50 kompozisyonlu toz alaşımı mekanik alaşımlama tekniği ile sentezlenmiştir. Mekanik alaşımlama süresinin, toz alaşımın faz değişimine ve mikro sertliğine etkisi X-ışını kırınımı (XRD), taramalı elektron mikroskobu (SEM) ve Vickers mikro sertlik (HV) cihazı ile incelenmiştir. Alaşımın mikro sertlik değeri artan mekaniksel alaşımlama zamanı ile yükseldi ve final ürün için ~600 Mpa olarak ölçülmüştür. Mg50Cu50 alaşımının kristal boyutu XRD piklerinin genişlemesi ile Debye Scherrer eşitliği kullanılarak hesaplanmıştır. Toz alaşımın kristal boyutu ayrıca geçirimli elektron mikroskobu (TEM) ile teyit edildi ve yaklaşık 10 nm olarak belirlenmiştir. Mekanik olarak alaşımlanan Mg50Cu50 tozlarının termal özellikleri diferansiyel taramalı kalorimetri ile (DSC) analiz edilmiştir. DSC sonuçlarına göre ~ 650 ˚C’ de Magnezyum (Mg) elementinin erime sıcaklığına ait endotermik bir pik gözlenmiştir.
Nanocrystalline Mg50Cu50 powders produced by mechanical alloying
In the present study, binary mixture of Mg and Cu with nominal composition of nanocrystalline Mg50Cu50 powder alloy was synthesized by mechanical alloying. The effect of mechanical alloying time on the phase evolution and microhardness of the powder alloy was investigated by X-Ray diffractometry (XRD), scanning electron microscopy (SEM) and Vickers microhardness (HV) tester. The micro hardness value of the alloy increased with increasing mechanical alloying time and it was measured ~600 Mpa for final product. The crystallite size of Mg50Cu50 alloy calculated with broadening of XRD peaks by Debye Scherrer equation. The crystallite size of the powder alloy was also confirmed by transmission electron microscopy (TEM) and it was determined approximately 10 nm. Thermal properties of the mechanically alloyed Mg50Cu50 powders were examined by differential scanning calorimetry (DSC). From DSC traces, an endothermic peak which belongs to melting point of Magnesium (Mg) element was observed at ~ 650 ˚C
___
- D. Zhao, Q.M. Dong, P. Liu, B.X. Kang, J.L.
Huang, Z.H. Jin, “Aging behavior of Cu–
Ni–Si alloy,” Mater. Sci. Eng., A, vol. 361,
pp. 93-99, 2003.
- M. Azimi, G.H. Akbari, “Characterization of
nano-structured Cu–6 wt.% Zr alloy
produced by mechanical alloying and
annealing methods,” J. Alloys Compd., vol.
555, pp. 112-116, 2013
- K.J. Laws, K.F. Shamlaye, J.D. Cao, J.P.
Scicluna, M. Ferry, “Locating new Mg based
bulk metallic glasses free of rare earth
elements,” J. Alloys Comp., vol. 542, pp.
105–110, 2012.
- P. Rojas, S. Ordonez, D. Serafini, A. Zuniga,
E. Lavernia, “Microstructural evolution
during mechanical alloying of Mg and Ni,”
J. Alloys Comp., vol. 391, pp. 267–276,
2005.
- Y. Zhenxing, L. Zuyan, W. Erde, “Hydrogen
storage properties of nanocomposite Mg–
Ni–Cu–CrCl3 prepared by mechanical
alloying,” Mater. Sci. Eng., A, vol. 335, pp.
43–48, 2002.
- R. Ölmez, G. Çakmak, T. Öztürk,
“Combinatorial search for hydrogen storage
alloys: Mg-Ni and Mg-Ni-Ti,” Int. J.
Hydrogen Energy, vol. 35, pp. 11957 -
11965, 2010.
- B. Zhang, Y. Lv, J. Yuan, Y. Wu, “Effects
of microstructure on the hydrogen storage
properties of the melt-spun Mg-5Ni-3La
(at.%) alloys,” J. Alloys Comp., vol. 702, pp.
126-131, 2017.
- Y. Zhou, L. Bian, G. Chen, L. Wang, W.
Liang, “Influence of Ca addition on
microstructural evolution and mechanical
properties of near-eutectic Mg-Li alloys by
copper-mold suction casting,” J. Alloys
Comp., vol. 664, pp. 85-91, 2016.
- A. Fikadu, B. Hertog, O. Ledyaev, D.
Volovik, R. Miller, A. Osinsky, S. Bakhshi,
W. V. Schoenfeld, “High responsivity solar
blind photo detector based on high Mg
content MgZnO film grown via pulsed metal
organic chemical vapour deposition,” Sens.
Actuators A, vol. 249, pp. 263–268, 2016.
- X.K. Xi, D.Q. Zhao, M.X. Pan, W.H. Wang,
“On the criteria of bulk metallic glass
formation in MgCu-based alloys,”
Intermetallics, vol. 13, pp. 638–641, 2005.
- C. Suryanarayana, “Mechanical alloying and
milling,” Prog Mater Sci., vol. 46, pp. 1-184,
2001.
- C. Aguilar, D. Guzmán, F. Castro, V.
Martínez, F. Cuevas, S. Lascano, T.
Muthiah, “Fabrication of nanocrystalline
alloys Cu-Cr-Mo super satured solid
solution by mechanical alloying,” Mater.
Chem. Phys., vol. 146, pp. 493-502, 2014.
- K. Wieczerzak, P. Bala, R. Dziurka, T.
Tokarski, G. Cios, T. Koziel, L. Gondek,
“The effect of temperature on the evolution
of eutectic carbides and M7C3 - M23C6
carbides reaction in the rapidly solidified FeCr-C alloy,” J. Alloys Compd., vol. 698, pp.
673-684, 2017.
- Y. Guo, L. Jia, B. Kong, S. Zhang, F. Zhang,
H. Zhang, “Microstructure and surface
oxides of rapidly solidified Nb-Si based
alloy powders,” Mater. Des., vol. 120, pp.
109–116, 2017.
- Y. Wang, H. Ji, X. Yan, H. Gao, W. Ma, Z.
Zhang, “Microstructural and compositional
evolution of nanoporous silver during
dealloying of rapidly solidified Mg65Ag35
alloy,” Intermetallics, vol. 76, pp. 49-55,
2016.
- A. A. Al-Joubori, C. Suryanarayana,
“Synthesis of stable and metastable phases
in the Ni-Si system by mechanical alloying,”
Powder Technol., vol. 302, pp. 8–14, 2016.
- K.B. Gerasimov, V.V. Boldyrev, “On
mechanism of new phases formation during
mechanical alloying of Ag-Cu, Al-Ge and
Fe-Sn systems,” Mater. Res. Bull., vol. 31,
pp. 1297–1305, 1996.
- Y.C. Kim, J.C. Lee, P.R. Cha, J.P. Ahn, E.
Fleury, “Enhance glass forming ability and
mechanical properties of new Cu-based bulk
metallic glasses,” Mater. Sci. Eng., A, vol.
437, pp. 248–253, 2006.
- T. Spassov, P. Solsona, S. Surinach, M.D.
Baro, “Optimisation of the ball-milling and
heat treatment parameters for synthesis of
amorphous and nanocrystalline Mg2Nibased alloys,” J. Alloys Compd., vol. 349,
pp. 142–254, 2003.
- S. Venkataraman, W. Loser, J. Eckert, T.
Gemming, C. Mickel, P. Schulbert-Bischoff,
N. Wanderka, L. Schultz, D.J. Sordelet,
“Nanocrystal development in
Cu47Ti33Zr11Ni8Si1 metallic glass powders,”
J. Alloys Compd, vol. 415, pp. 162–169,
2006.
- S. Mula, S. Ghosh, S.K. Pabi, “Synthesis of
an Al-based Al–Cr–Co–Ce alloy by
mechanical alloying and its thermal
stability,” Mater. Sci. Eng., A, vol. 472, pp.
208–213, 2008.
- R. Lei, M. Wang, H. Wang, S. Xu, “New
insights on the formation of supersaturated
Cu-Nb solid solution prepared by
mechanical alloying,” Mater. Charact., vol.
118, pp. 324–331, 2016.
- C. Suryanarayana, M. G. Norton, “X-ray
Diffraction: A Practical Approach,” Plenum
Press, New York, 1998. 207.
- J. Guerrero-Paz, D. Jaramillo-Vigueras,
“Comparison of grain size distributions
obtained by XRD and TEM in milled FCC
powders,” Nanostrcut Mater., vol. 11, pp.
1195-1204, 1999.
- J. N. R. Olvera, A. Martínez Janete, H. H.
Hernandez, I. Orozco G., L. D. B. Arceo,
“Microstructural characterization and
thermodynamic analysis of MoZn produced by mechanical alloying,” J. Alloys Compd.,
vol. 696, pp. 329-337, 2017.
- S. Jayalakshmi, S. Sahu, S.
Sankaranarayanan, S. Gupta, M. Gupta,
“Development of novel Mg–Ni60Nb40
amorphous particle reinforced composites
with enhanced hardness and compressive
response,” Mater. Des., vol. 53, pp. 849–
855, 2014.
- A. Kumar, G. K. Meenashisundaram, V.
Manakari, G. Parande, M. Gupta,
“Lanthanum effect on improving CTE,
damping, hardness and tensile response of
Mg-3Al alloy,” J. Alloys Compd., vol. 695,
pp. 3612-3620, 2017.
- S. Sankaranarayanan, S. Jayalakshmi, M.
Gupta, “Effect of addition of mutually
soluble and insoluble metallic elements on
the microstructure, tensile and compressive
properties of pure magnesium,” Mater. Sci.
Eng., A, vol. 530, pp. 149–160, 2011.
- J. Zhu, X.H. Chen, L. Wang, W.Y. Wang,
Z.K. Liu, J.X. Liu, X.D. Hui, “High strength
Mg-Zn-Y alloys reinforced synergistically
by Mg12ZnY phase and Mg3Zn3Y2 particle,”
J. Alloys Compd., vol. 703, pp. 508-516,
2017.
- K.R. Ramkumar, S. Ilangovan, S.
Sivasankaran, A. S. Alaboodi, Experimental
investigation on synthesis and structural
characterization of Cu-Zn-x wt%Al2O3 (x ¼
0, 3, 6, 9 & 12%) nanocomposites powders
through mechanical alloying,” J. Alloys
Compd., vol. 688, pp. 518-526, 2016.
- C. Díaz-Guillén, E. E. Granda-Gutiérrez, G.
Vargas-Gu tiérrez, M. R. Díaz-Guillén, J. A.
Aguilar-Martínez, L. Álvarez-Contreras, “Effect
of Nitriding Current Density on the Surface
Properties and Crystallite Size of Pulsed PlasmaNitrided AISI 316L,” J. of Mat. Sci. and Chem.
Eng., vol. 3, pp. 45-51, 2015.