C. Nazik, N. Tarakcioglu, A. Canakci, T. Varol, S. Ozkaya -

Enhanced properties of an AA7075 based metal matrix composite prepared using mechanical alloying

In this study, firstly, AA7075 metal powder which average particle size 43.9 µm were manufactured by using gas atomization method. Thereafter with mechanical alloying method which powder metallurgy manufacturing methods, 10% B4C particle reinforcements that average particle size of 49.5 µm by participating into AA7075 metal matrix composite powder mixtures were prepared. They were milled for different durations (0-8 hrs) in a high energy planetary ball mill. From these milled powders; 550°C and under pressure 500 MPa, composite materials were produced by the method of hot pressing. In SEM analysis, after 4 hrs with mechanical alloying method, B4C particles which were homogenously distrubuted into the matrix of AA7075 were seen. Powders size increased to 1 hr and then decrease. In order to determine produced composite material's microstructural properties SEM analysis and determine physical and mechanical properties, density test and hardness test was applied. As a result of the experiments, composite density increased to 1 hr and then decrease. The hardness of composite was increased with increasing milling time and the rate of reinforcement.

Anahtar Kelimeler:

B4C, mechanical alloying, metal-matrix composite, powder metallurgy

Enhanced properties of an AA7075 based metal matrix composite prepared using mechanical alloying

Keywords:

B4C, mechanical alloying, metal-matrix composite, powder metallurgy,

PDF

___

Acılar M. Investigation of production and wear behaviour of Al/SiC composites by vacuum infiltration technique, PhD Thesis, Gazi University, Ankara, Turkey, 44 – 62, 2002.
Kumdalı F. The production of Al based composites reinforced with B 4 C by powder metallurgy, MSc thesis, Yıldız Technical University, İstanbul, Turkey, 1 – 2, 200 Varol T. The production of AA2024 matrix-B 4 C particle reinforced composites by powder metallurgy method and investigation of their properties, MSc thesis, Karadeniz Technical University, Trabzon, Turkey, 1 – 25, 2012.
Canakci A. Manufacturing of AA2024 matrix-B 4 C particle reinforced composites by vortex method and investigation of their properties, PhD Thesis, Karadeniz Technical University, Trabzon, Turkey, 10 – 21, 2006.
Canakci A, Arslan F and Varol T. Effect of volume fraction and size of B 4 C particles on production and microstructure properties of B 4 C reinforced aluminum alloy composites. Materials Science and Technology, 2013; 29: 954 – 9
Varol T, Canakci A and Ozsahin S. Artificial neural network modeling to effect of reinforcement properties on the physical and mechanical properties of Al2024B 4 C composites produced by powder metallurgy. Composites: Part B, 2013; 54: 224 – 233.
Canakci A, Varol T and Ozsahin S. Prediction of effect of volume fraction, compact pressure and milling time on properties of Al-Al 2 O 3 MMCs using neural networks. Metals and Materials International, 2013; 19: 519 – 526. Varol T and Canakci A, Effect of particle size and ratio of B 4 C reinforcement on properties and morphology of nanocrystalline Al2024-B 4 C composite powders. Powder Technology, 2013; 246: 462 – 472.
Varol T and Canakci A. Effect of weight percentage and particle size of B 4 C reinforcement on physical and mechanical properties of powder metallurgy Al2024-B 4 C composites. Metals and Materials International, 2013; 19: 1227 – 12
Canakci A, Varol T and Ertok S. The effect of mechanical alloying on Al 2 O 3 distribution and properties of Al 2 O 3 particle reinforced Al-MMCs. Science and Engineering of Composite Materials, 2012; 19: 227 – 235.
Canakci A and Varol T. Production and microstructure of AA2024-B 4 C metal matrix composites by mechanical alloying method. Usak University Journal of Material Sciences, 2012; 1: 15 – 22.