Adsorptive performance of MWCNTs for simultaneous cationic and anionic dyes removal; kinetics, thermodynamics, and isotherm study

Adsorptive performance of MWCNTs for simultaneous cationic and anionic dyes removal; kinetics, thermodynamics, and isotherm study

Disposal of contaminated wastewater causes many serious problems especially when it gets mixed with the ground and seawater. It is, therefore, important to apply any remedial action to eradicate dangerous pollutants from the aqueous effluents and to avoid exposure of this wastewater to aquatic life. The research results discussed herein deal with the removal of Rhodamine B (RhB) and Congo Red (CR) dye from wastewater by using multi-walled carbon nanotubes (MWCNTs) as an adsorbent. Different factors like solid dosage, initial pH and concentration, time, and temperature were studied to understand the behavior and mechanism of adsorption. The maximum adsorption capacity in case of a single component system was found to be 302 mg/g and 300 mg/g for Congo Red and Rhodamine B, respectively. Moreover, the mechanism of adsorption was best described by a pseudo-second-order kinetic model. Thermodynamic parameters showed that adsorption of CR and RhB was exothermic when these were removed from a single dye system. However, the overall process became endothermic for concurrent removal of both dyes from the solution. The research results showed that the MWCNTs could successfully be utilized to remove the dye from the industrial wastewater.

___

  • 1. Bildika F, Turana GT, Duranb H, Şişmanoğlub T, Senkala BF. Sorption of acidic dyes from water by poly (vinyl imidazole) grafted onto poly (styrene) based beads. Desalination and Water Treatment (2019); 169: 353-362.
  • 2. Noroozi B, Sorial G, Bahrami H, Arami M. Adsorption of binary mixtures of cationic dyes. Dyes and Pigments 2008; 76 (3): 784-791.
  • 3. Karakuş S, Şişmanoğlu S, Akdut G, Ürk Ö, Tan E et al. Removal of Basic Blue 3 from the aqueous solution with ternary polymer nanocomposite: swelling, kinetics, isotherms and error function. Journal of the Chemical Society of Pakistan 2017; 39 (1): 17-25.
  • 4. Robinson T, McMullan G, Marchant R, Nigam P. Remediation of dyes in textile effluent: a critical review on current treatment technologies with a proposed alternative. Bioresource Technology 2001; 77 (3): 247-255.
  • 5. Eren E, Afsin B. Investigation of a basic dye adsorption from aqueous solution onto raw and pre-treated bentonite surfaces. Dyes and Pigments 2008; 76 (1): 220-225.
  • 6. Durana H, Sismanoglub S, Sismanoglua T. Binary biomaterials (inorganic material/natural resin): synthesis, characterization and performance for adsorption of dyes. Journal of the Indian Chemical Society 2019; 96: 1245-1251.
  • 7. Marungrueng K, Pavasant P. Removal of basic dye (Astrazon Blue FGRL) using macroalga Caulerpa lentillifera. Journal of Environmental Management 2006; 78 (3): 268-274.
  • 8. Waranusantigul P, Pokethitiyook P, Kruatrachue M, Upatham E. Kinetics of basic dye (methylene blue) biosorption by giant duckweed (Spirodela polyrrhiza). Environmental Pollution 2003; 125 (3): 385-392.
  • 9. Sismanoglu S. Investigation by UV spectrophotometry of removal of para-nitrophenol on raney alloy. Journal of Molecular Structure 2018; 1174: 107-111.
  • 10. Juang R, Wu F, Tseng R. The ability of activated clay for the adsorption of dyes from aqueous solutions. Environmental Technology 1997; 18 (5): 525-531.
  • 11. Wang S, Boyjoo Y, Choueib A, Zhu Z. Removal of dyes from aqueous solution using fly ash and red mud. Water Research. 2005; 39 (1): 129-138.
  • 12. Gupta V. Application of low-cost adsorbents for dye removal–a review. Journal of Environmental Management 2009; 90 (8): 2313-2342.
  • 13. Crini G. Non-conventional low-cost adsorbents for dye removal: a review. Bioresource Technology 2006; 97 (9): 1061-1085.
  • 14. Şişmanoğlu T, Pozan G. S. Adsorption of congo red from aqueous solution using various $TiO_2$ nanoparticles. Desalination and Water Treatment 2016; 57 (28): 13318-13333.
  • 15. Akdut G, Bildik F, Duran H, Tuna A, Şişmanoğlu T et al. Adsorption of bisphenol A and phenoxyacetic acid onto new polymeric adsorbents. Bulgarian Chemical Communications 2019; 51 (4): 541-551.
  • 16. Hanna Varghese S, Nair R, G Nair B, Hanajiri T, Maekawa T et al. Sensors based on carbon nanotubes and their applications: a review. Current Nanoscience 2010; 6 (4): 331-346.
  • 17. Wang L, Yang RT. New sorbents for hydrogen storage by hydrogen spillover–a review. Energy & Environmental Science 2008; 1 (2): 268- 279.
  • 18. De Jong KP, Geus JW. Carbon nanofibers: catalytic synthesis and applications. Catalysis Reviews 2000; 42 (4): 481-510.
  • 19. Beg S, Rizwan M, Sheikh AM, Hasnain MS, Anwer K et al. Advancement in carbon nanotubes: basics, biomedical applications and toxicity. Journal of Pharmacy and Pharmacology 2011; 63 (2): 141-163.
  • 20. Liu Z, Jiao L, Yao Y, Xian X, Zhang J. Aligned, ultralong single-walled carbon nanotubes: from synthesis, sorting, to electronic devices. Advanced Materials 2010; 22 (21): 2285-2310.
  • 21. Aslam Z, Qaiser M, Ali R, Abbas A, Ihsanullah, et al. $Al_2O_3/MnO_2$ /CNTs nanocomposite: synthesis and characterization study. Fullerenes, Nanotubes and Carbon Nanostructures 2019; 27 (7): 591-600.
  • 22. Ihsanullah, Abbas A, Al-Amer AM, Laoui T, Al-Marri MJ et al. Heavy metal removal from aqueous solution by advanced carbon nanotubes: critical review of adsorption applications. Separation and Purification Technology 2016; 157 (1): 141-161.
  • 23. Abbas A, Abussaud BA, Al-Baghli NA, Redhwi HH. Adsorption of toluene and paraxylene from aqueous solution using pure and iron oxide impregnated carbon nanotubes: kinetics and isotherms study. Bioinorganic Chemistry and Applications 2017; 2017 (1): 1-11
  • 24. Upadhyayula VK, Deng S, Mitchell MC, Smith GB. Application of carbon nanotube technology for removal of contaminants in drinking water: a review. Science of the Total Environment 2009; 408 (1): 1-13.
  • 25. Zahir A, Aslam Z, Kamal MS, Ahmad W, Abbas A et al. Development of novel cross-linked chitosan for the removal of anionic Congo red dye. Journal of Molecular Liquids 2017; 244 (1): 211-218.
  • 26. Saruchi KV. Adsorption kinetics and isotherms for the removal of rhodamine B dye and Pb2+ ions from aqueous solutions by a hybrid ion-exchanger. Arabian Journal of Chemistry 2016; 10 (1): 316-329.
  • 27. Postai DL, Demarchi CA, Zanatta F, Melo DCC, Rodrigues CA. Adsorption of rhodamine B and methylene blue dyes using waste of seeds of Aleurites Moluccana, a low cost adsorbent. Alexandria Engineering Journal 2016; 55 (2): 1713-1723.
  • 28. Nethaji S, Sivasamy A, Mandal A. Adsorption isotherms, kinetics and mechanism for the adsorption of cationic and anionic dyes onto carbonaceous particles prepared from Juglans regia shell biomass. International Journal of Environmental Science and Technology 2013; 10 (2): 231-242.
  • 29. Crini G, Peindy HN, Gimbert F, Robert C. Removal of CI Basic Green 4 (Malachite Green) from aqueous solutions by adsorption using cyclodextrin-based adsorbent: kinetic and equilibrium studies. Separation and Purification Technology 2007; 53 (1): 97-110.
  • 30. Ayawei N, Ebelegi AN, Wankasi D. Modelling and interpretation of adsorption isotherms. Journal of Chemistry 2017; 2017 (1): 3039817- 3039827.
  • 31. Hernández-Montoya V, Pérez-Cruz MA, Mendoza-Castillo DI, Moreno-Virgen M, Bonilla-Petriciolet A. Competitive adsorption of dyes and heavy metals on zeolitic structures. Journal of Environmental Management. 2013; 116 (1): 213-221.
  • 32. Turabik M. Adsorption of basic dyes from single and binary component systems onto bentonite: Simultaneous analysis of Basic Red 46 and Basic Yellow 28 by first order derivative spectrophotometric analysis method. Journal of Hazardous Materials 2008; 158 (1): 52-64.
  • 33. Girish C. Various isotherm models for multicomponent adsorption: a review. International Journal of Civil Engineering and Technology 2017; 8 (10): 80-86.
  • 34. Singh N, Balomajumder C. Simultaneous removal of phenol and cyanide from aqueous solution by adsorption onto surface modified activated carbon prepared from coconut shell. Journal of Water Process Engineering 2016; 9 (1): 233-245.
  • 35. Wei J, Liu Y, Li J, Zhu Y, Yu H et al. Adsorption and co-adsorption of tetracycline and doxycycline by one-step synthesized iron loaded sludge biochar. Chemosphere 2019; 236 (1): 124254.
  • 36. Olajire AA, Giwa AA, Bello IA. Competitive adsorption of dye species from aqueous solution onto melon husk in single and ternary dye systems. International Journal of Environmental Science and Technology 2015; 2 (3): 939-950.
  • 37. Konicki W, Aleksandrzak M, Moszyński D, Mijowska E. Adsorption of anionic azo-dyes from aqueous solutions onto graphene oxide: equilibrium, kinetic and thermodynamic studies. Journal of Colloid and Interface Science 2017; 496 (1): 188-200.
  • 38. Mohammed MI, Baytak S. Synthesis of bentonite–carbon nanotube nanocomposite and its adsorption of rhodamine dye from water. Arabian Journal for Science and Engineering 2016; 41 (12): 4775-4785.
  • 39. Dutta DP, Venugopalan R, Chopade S. Manipulating carbon nanotubes for efficient removal of both cationic and anionic dyes from wastewater. Chemistry Select 2017; 2 (13): 3878-3888.
  • 40. Wu C-H. Adsorption of reactive dye onto carbon nanotubes: equilibrium, kinetics and thermodynamics. Journal of Hazardous Materials 2007; 144 (1-2): 93-100.
  • 41. Kuo C-Y, Wu C-H, Wu J-Y. Adsorption of direct dyes from aqueous solutions by carbon nanotubes: determination of equilibrium, kinetics and thermodynamics parameters. Journal of Colloid and Interface Science 2008; 327 (2): 308-315.
  • 42. Gong J-L, Wang B, Zeng G-M, Yang C-P, Niu C-G et al. Removal of cationic dyes from aqueous solution using magnetic multi-wall carbon nanotube nanocomposite as adsorbent. Journal of Hazardous Materials 2009; 164 (2-3): 1517-1522.
  • 43. Yao Y, Miao S, Liu S, Ma LP, Sun H et al. Synthesis, characterization, and adsorption properties of magnetic $Fe_3 O_4@$ graphene nanocomposite.Chemical Engineering Journal 2012; 184 (1): 326-332.
  • 44. Ghaedi M, Hassanzadeh A, Kokhdan SN. Multiwalled carbon nanotubes as adsorbents for the kinetic and equilibrium study of the removal of alizarin red S and morin. Journal of Chemical & Engineering Data 2011; 56 (5): 2511-2520.
Turkish Journal of Chemistry-Cover
  • ISSN: 1300-0527
  • Yayın Aralığı: Yılda 6 Sayı
  • Yayıncı: TÜBİTAK
Sayıdaki Diğer Makaleler

Feature of catalysis on bimetallic alloys Zr with V, Mo, and Fe in the reaction of methanol oxidation

Arif EFENDI, Lala MAGERRAMOVA, Adila ALIYEVA, Lyudmila KOJA ROVA, Elmir BABAYEV

Synthesis and characterization of benzodioxinone mono-telechelics and their use in block copolymerization

Cumali ÇELİK

Preparation of ethyl levulinate from wheat stalk over $Zr(SO_4)_2/SiO_2$

Ding kai WANG, Wei ZHAO, Ming yu CUI, Tian-tian GUO, Shui yuan FU, Wei gang LI

Sensitive and selective determination of imidacloprid with magnetic molecularly imprinted polymer by using LC/Q-TOF/MS

Raif İLKTAÇ, Zinar Pınar GÜMÜŞ

Novel mixed ligand coordination compounds of some rare earth metal cations containing acesulfamato/N,N-diethylnicotinamide

Dursun Ali KÖSE, Leriman ZEYBEL

Detection of bacteria using antimicrobial polymer derived via ring-opening metathesis (romp) pathway

Mustafa OKUTAN, Markus GALLE, Hüsnü CANKURTARAN, N. Ceren SÜER, Tarık EREN, Tülin ARASOĞLU

Catalytic, theoretical, and biological investigation of an enzyme mimic model

Gülcihan GÜLSEREN

Preparation and characterization of templated porous carbons from sucrose by one-pot method and application as a $CO_2$ adsorbent

Meltem GÜRBÜZ, Fatma TÜMSEK

Adsorptive performance of MWCNTs for simultaneous cationic and anionic dyes removal; kinetics, thermodynamics, and isotherm study

Abdul ZAHIR, Adnan AKHTAR, Zaheer ASLAM, Irfan YOUSAF

Hybrid paper sheets with improved barrier properties

Çağla SÖZ