THE DYNAMICAL BEHAVIOUR OF THE DOUBLE - SHOES BRAKE USED IN ELEVATORS

The double-shoe braking system used in elevators of buildings with the purpose of mechanical braking behavior are used an experimental method for the preparation of the dynamic model in this study. The double-shoe braking system is used in many mechanisms. The double –shoe braking system is a complex structure consisting of many parts, so that it is difficult to create a model with a theoretical approach to make the right contact definitions. Therefore, experiments were performed by creating experimental model in this study and the results of these experiments have shown that the structural noise and vibrations were significantly affected by the speed, and braking and take-off acceleration of the engine.

Keywords:

Elevators, elevator safety systems double-shoe brakes, vertical transportation systems,

PDF

___

[1] Hirasata K., Hayashi K., Inamoto Y., (2007) Friction and wear of several kinds of cast irons under severe sliding conditions. Wear, 263, 790–800.
[2] Xiao P., Li Z., Xiong X., (2010) Microstructure and tribological properties of 3D needle-punched C/C-SiC brake composites, Solid State Sciences,12,617-623.
[3] Zhuan L.,Xiao P.,Zhang B.,Li Y.,Lu Y., (2015) Preparation and tribological properties of C/C-SiC brake composites modified by in situ grown carbon nanofibers,Ceramics International 41,11733-11740.
[4] Zhuan L., Li Y., Zhang B., Lu Y., Xiao P., (2015) Microstructure and tribological characteristics of needled C/C-SiC brake composites fabricated by simultaneous infiltration of molten Si and Cu, Tribology International 93 ,220-228.
[5] Fan S., Zhang L., Cheng L., Zhang J., Yang S., Liu H., (2011) Wear mechanism of the C/SiC brake materials, Tribology International,44, 25-28.
[6] Fan S., Zhang L., Xu Y., Cheng L., Tian G., Ke S., Xu F., Liu H., (2008) Microstructure and tribological propertyie of advanced carbon/silicon carbide aircraft brake materials, Composites Science and Technology,3002-3009.
[7] Yokoi M.,Nakai M.A., (1979) A fundamental study on frictional noise (1 st report, the generating mechanism of rubbing noise and squel noise) Bull JSME,22:1665-1671.
[8] Yokoi M.,Nakai M.A., (1980) A fundamental study on frictional noise (2 nd report, the generating mechanism of rubbing noise and squel noise) Bull JSME,23:2118-2124.
[9] Yokoi M.,Nakai M.A., (1981) A fundamental study on frictional noise (3 rd report, the influence of periodic surface roughness on frictional noise) Bull JSME,24:1470-1476.
[10] Yokoi M.,Nakai M.A., (1981) A fundamental study on frictional noise (4 th report, the influence of periodic surface roughness on frictional noise) Bull JSME,24:1477-1483.
[11] Yokoi M.,Nakai M.A., (1982)A fundamental study on frictional noise (5 th report, the influence of periodic surface roughness on frictional noise) Bull JSME,25:827-833.
[12] Lindberg E., Hörlin N.E.,Göransson P.,82013) An experimental study of interior vehicle roughness noise from disc brake systems, Applied Acoustics ,396-406.
[13] Yurtsevevn a H., (2010) Asansörlerde kullanılan fren balatalarının tribolojik özelliklerinin deneysel incelenmesi, Yüksek Lisans Tezi, Süleyman Demirel Üniversitesi Fen Bilimleri Enstitüsü,Isparta.
[14] Bettege D., Starcevic J.,(2003) Topographic properties of the contact zones of wear surfaces in disc brakes, Wea,254,195-202.
[15] Ostermeyer G P.,(2001) Friction and wear of brake systems, Forschung im Ingenieurwesen,66,267- 272
[16] Severin D., Dörsch S.,(2001) Friction mechenism in industrial brakes, Wear,249,771-779.
[17] Hohmann C., Schiffner K., Oerter K., Reese H.,(1999) Contact analysis of drum brakes and disc brakes using Adina, Computer&Structures,72,185-198.
[18] Ripin Z B.,(1995)Analysis of disc brake squel using the finite element method, PhD Thesis, University of Leeds.
[19] Tirovic M., Day A J., (1991) Disc brake interface pressure distributions, Proc. Ins.Mech.Journal of Automobile Engineering,Part D,205,137-146
[20] Verma P,C.,Menapace L., Bonfanti A., Ciudin R., (2014) Braking pad-disc system:Wear mechanism and formation of wear fragments, Wear 322-323,251-258.
[21] Camacho J.R.L., Morales G.J., Ramon C.C., Martinez V.V., Romero I.H., MendezJ.V.M., Torres M.V., (2015) A study of the wear mechanisms of disk and shoe brake pads, Engineering Failure Analysis 56,348- 359.
[22] Abdulwahab A.,Alnaqi A., Barton D.C., Brooks C., (2015) Reduced scale thermal characterization of automotive disc brake,Applied Thermal Engineering 75,658-668.
[23] Çavdar K., Karpat B., Güngören Y., (2005) Asansörler için paraşüt fren sistemi tasarımı. TMMOB Makine Mühendisleri Odası II. İletim Teknolojileri Kongre ve Sergisi, İstanbul, 27-28 Mayıs 2005.
[24] Bedir S., (2007) Çift yönlü asansör fren bloklarının modellenmesi ve sonlu elemanların analizi. Yüksek Lisans Tezi, İTÜ Fen Bilimleri Enstitüsü, İstanbul.
[25] Ersavaş M., (2009) Çift yönlü asasnsör fren bloklarının modellenmesi ve sonlu elemanların analizi, Yüksek Lisans Tezi, İTÜ Fen Bilimleri Enstitüsü, İstanbul.
[26] De Jong J., (2001) Understanding the natural behaviour of elevator safety gears and their triggering devices. Elevator Technology, 14 IAEE.

Sigma Mühendislik ve Fen Bilimleri Dergisi-Cover

ISSN: 1304-7191
Yayın Aralığı: Yılda 4 Sayı
Yayıncı: Yıldız Teknik Üniversitesi

Arşiv