GÜLŞAH AKINCIOĞLU, SITKI AKINCIOĞLU, İLYAS UYGUR, HASAN ÖKTEM

Bor oksit tozunun fren balatalarının tribolojik özelliklerine etkisi

Bu çalışmada, Renault Clio otomobilin fren balatası, bor oksit tozu katkısı ile sıcak presleme yöntemiyle üretilerek, bor oksit tozunun balatanın tribolojik özellikleri üzerine etkisi deneysel olarak araştırılmıştır. Son yıllarda çevre dostu malzemelerin kullanılmasının önem kazanmasından dolayı fren balatasının içeriğinde bor oksit kullanılmıştır. Ayrıca bu malzemenin seçilmesinde ülke ekonomisine fayda sağlamakta amaçlanmıştır. Karşılaştırma yapmak için ticari Clio balatası kullanılmıştır. Balata numunelerinin aşınma sürtünme deneyleri Chase tipi cihazda yapılmıştır. Bor oksit katkısının fren balatasının aşınma sürtünme performansına etkisi ticari fren balatasının sonuçlarıyla kıyaslanarak incelenmiştir. Sonuçta bor oksit katkısının sürtünme katsayısına olumlu etki yaptığı gözlenmiştir.

The effects of boron oxide powders on the tribological properties of brake pads

In this study, the Renault Clio car was produced by hot press method with boron oxide powder additive and the effect on the tribological properties of the boron oxide additive was experimentally investigated. In recent years, the use of environmentally friendly materials has become important, so boron oxide has been used in the brake pad. Also it aimed at providing benefits to the national economy in the selection of these materials. Clio commercial pads were used for comparison. Friction linings wear testing of samples are carried out Chase type device. The effect of the boron oxide additive brake wear on wear friction performance has been investigated in comparison with the results of commercial brake pad. As a result, it was observed that the boron oxide contribution has a positive effect on the friction coefficient.

PDF

___

M. Jacko and S. Rhee, "Brake linings and clutch facings," Kirk-Othmer encyclopedia of chemical technology, 1992.
I. Mutlu, O. Eldogan, and F. Findik, "Production of ceramic additive automotive brake lining and investigation of its braking characterisation," Industrial Lubrication and Tribology, vol. 57, pp. 84-92, 2005.
P. W. Lee and P. Filip, "Friction and wear of Cu-free and Sb-free environmental friendly automotive brake materials," Wear, vol. 302, pp. 1404-1413, 2013.
N. Aranganathan and J. Bijwe, "Development of copper-free eco-friendly brake-friction material using novel ingredients," Wear, vol. 352, pp. 79-91, 2016.
W. Österle, C. Prietzel, H. Kloß, and A. Dmitriev, "On the role of copper in brake friction materials," Tribology International, vol. 43, pp. 2317-2326, 2010.
R. Yun, P. Filip, and Y. Lu, "Performance and evaluation of eco-friendly brake friction materials," Tribology International, vol. 43, 2010.
E. Omrani, P. L. Menezes, and P. K. Rohatgi, "State of the art on tribological behavior of polymer matrix composites reinforced with natural fibers in the green materials world," Engineering Science and Technology, an International Journal, vol. 19, pp. 717-736, 2016.
L. Barros, P. Neis, N. Ferreira, R. Pavlak, D. Masotti, L. Matozo, et al., "Morphological analysis of pad–disc system during braking operations," Wear, vol. 352, pp. 112-121, 2016.
H. Öktem, İ. Uygur, G. Akıncıoğlu, D. Kır, and H. Karakaş, "Evaluation of non-asbestos high performance brake pads produced with organic dusts," ed: Metal, 2015.
W. Wannik, A. Ayob, S. Syahrullail, H. Masjuki, and M. Ahmad, "The effect of boron friction modifier on the performance of brake pads," International Journal of Mechanical and Materials Engineering, vol. 7, pp. 31-35, 2012.
E. M. İ. G. Müdürlüğü, "Bor Sektör Raporu," 2009.
I. Mutlu, C. Oner, and F. Findik, "Boric acid effect in phenolic composites on tribological properties in brake linings," Materials & design, vol. 28, pp. 480-487, 2007.
G. Yi and F. Yan, "Effect of hexagonal boron nitride and calcined petroleum coke on friction and wear behavior of phenolic resinbased friction composites," Materials Science and Engineering: A, vol. 425, pp. 330-338, 2006.
R. Steege and F. Marx, "A new approach to material compressibility of brake pads," SAE Technical Paper 0148-7191, 2008.
A. Spencer, W. M. Spurgeon, and J. Winge, "Four tests for consistency of automotive brake linings," SAE Technical Paper 0148- 7191, 1966.
S. Anoop, S. Natarajan, and S. K. Babu, "Analysis of factors influencing dry sliding wear behaviour of Al/SiCp–brake pad tribosystem," Materials & Design, vol. 30, pp. 3831-3838, 2009.
M. Boz and A. Kurt, "Effect of ZrSiO4 on the friction performance of automotive brake friction materials," Journal of materials science & technology, vol. 23, p. 843, 2007.
İ. B. Algan and A. Kurt, "The Effect of Metal Fibres and Borax Powders on the Wear and Friction Performances of the Organic Based Brake Pads," Металлофизика и новейшие технологии, 2017.