Kaplama Atıklarından Üretilen Çimentolu Yongalevhaların Fiziksel ve Mekanik Özelliklerine Pres Parametrelerinin Etkisi
Bu çalışmanın amacı, kavak kaplama atıkları (Populus tremula L.) kullanılarak üretilen çimentolu yongalevhaların fiziksel ve mekanik özelliklerine pres sıcaklık ve süre değişiminin etkisinin araştırılmasıdır. Bu çalışmada, 5 farklı presleme parametresi kullanılarak 1200 kg/m3 hedef yoğunluğa ve 500 x 500 x 10 mm3 boyutlarına sahip tek tabakalı çimentolu yongalevhalar üretilmiştir. Üretilen levhaların fiziksel (rutubet içeriği, yoğunluk, su alma ve kalınlık artımı) ve mekanik (eğilme direnci, eğilmede elastikiyet modülü, yüzeye dik çekme direnci ve vida tutma direnci) özellikleri incelenmiştir. Elde edilen sonuçlara göre, pres süresi ve sıcaklıktaki değişimler su emme alma önemli bir değişikliğe neden olmazken, presleme süresindeki artış kalınlık artımı değerlerini olumlu yönde etkilemiştir. Pres süresinin artmasıyla mekanik özellikler artarken, tüm levha gruplarında standarda uygun değerler elde edilmiştir. Ayrıca üretim için en uygun zamanın 24 saat olduğu ve sıcaklık uygulamasının levha özellikleri üzerinde önemli bir etkisinin olmadığı belirlenmiştir.
The Effect of Press Parameters on the Physical and Mechanical Properties of Cement-Bonded Particleboards Produced from Veneer Wastes
This study aims to investigate the effect of press temperature and time changes on the physical and mechanical properties of cement-bonded particleboards produced using poplar veneer wastes (Populus tremula L.). In this study, single-layer cement-bonded particleboards with a target density of 1200 kg/m3 and a size of 500 x 500 x 10 mm3 were produced using 5 different pressing parameters. The physical (moisture content, density, water absorption, and thickness swelling) and mechanical (modulus of rupture, modulus of elasticity, internal bond strength, and s screw withdrawal strength) properties of the produced boards were investigated. According to the results obtained, the changes in press time and temperature did not cause a significant change in the water absorption values, while the increase in the pressing time affected the thickness swelling values positively. While the mechanical properties increased with the increase of the pressing time, values suitable for the standard were obtained in all board groups. In addition, it was determined that the most suitable time for production was 24 hours and the temperature application did not have a significant effect on the board properties
___
- Aras, U., Kalaycıoğlu, H., Yel, H., Çok, A. (2019). Effect of
cement and accelerator types on the physico-
mechanical properties of cement-bonded
particleboards. Journal of Anatolian Environmental
and Animal Sciences, 4(4), 627-631. DOI:
10.35229/jaes.641542
- Arruda Filho, N.T.D., Dantas, C.P., Leal, A.F., Barbosa,
N.P., Silva, C.G. & Alexandre, M.V. (2012).
Resistência mecânica de compósitos cimentícios
leves utilizando resíduos industriais e fibras de sisal.
Revista Brasileira de Engenharia Agrícola e
Ambiental, 16, 894-902. DOI: 10.1590/S1415-
43662012000800012
- Ashori, A., Tabarsa, T. & Sepahvand, S. (2012). Cement-
bonded composite boards made from poplar strands.
Construction and Building Materials, 26(1), 131-
134. DOI: 10.1016/j.conbuildmat.2011.06.001
- ASTM D1037. (2010). Standard test method for evaluating
properties of wood-based fibres and particle panel
materials, American Society for Testing and
Materials, USA.
- Del Menezzi, C.H.S., Gomez de Castro, V. & Rabelo de
Souza, M. (2007). Production and properties of a
medium density wood-cement boards produced with
oriented strands and silica fume. Maderas: Ciencia
y Tecnología, 9(2), 105-115. DOI: 10.4067/S0718-
221X2007000200001
- EN 310. (1993). Wood-based panels, determination of
modulus of elasticity in bending and bending
strength. European Committee for Standardization,
Brussels-Belgium.
- EN 317. (1993). Particleboards and fibreboards-
determination of swelling in thickness after
immersion in water. European Committee for
Standardization, Brussels-Belgium.
- EN 319. (1993). Particleboards and fiberboards,
determination of tensile strength perpendicular to
plane of the board. European Committee for
Standardization, Brussels, Belgium.
- EN 320. (2011). Particleboards and fibreboards -
Determination of resistance to axial withdrawal of
screws, European Committee for Standardization,
Brussels-Belgium.
- EN 322. (1993). Wood-based panels-Determination of
moisture content, European Committee for
Standardization, Brussels-Belgium.
- EN 323. (1993). Wood-based panels-Determination of
density, European Committee for Standardization,
Brussels-Belgium.
- EN 634-1. (1999). Cement-bonded particleboards -
specifications - Part 1: General requirements,
European Committee for Standardization, Brussels-
Belgium.
- EN 634-2. (2007). Cement-bonded particleboards -
Specifications - Part 2: Requirements for OPC
bonded particleboards for use in dry, humid and
external conditions, European Committee for
Standardization, Brussels, Belgium.
- Fan, M.Z, Bonfield, P. & Dinwoodie, J. (2006) Nature and
behavior of cement bonded particleboard: structure,
physical property and movement. Journal of
Materials Science, 41, 5666-5678. DOI:
10.1007/s10853-006-0286-2
- Fan, M.Z., Bonfield, P.W., Dinwoodie, J.M., Boxall, J. &
Breese, M.C. (2004). Dimensional instability of
cement-bonded particleboard: The effect of surface
coating. Cement and concrete research, 34(7), 1189-
1197. DOI: 10.1016/j.cemconres.2003.12.010
- Frybort, S., Mauritz, R., Teischinger, A. & Müller, U.
(2008). Cement Bonded Composites - A Mechanical
Review. Biosource, 3(2), 602-626.
- Godfrey, L., Ahmed, M.T., Gebremedhin, K.G., Katima,
J.H., Oelofse, S., Osibanjo, O., Richter, U.F. &
Yonli, A.H. (2019). Solid waste management in
Africa: governance failure or development
opportunity. In Regional Development in Africa,
(235-249) Rijeka: Intechopen.
- Hou, J., Jin, Y., Che, W. & Yu, Y. (2022). Value-added
utilization of wood processing residues into cement-
bonded particleboards with admirable integrated
performance. Construction and Building Materials,
344, 128144. DOI:
10.1016/j.conbuildmat.2022.128144
- Jarabo, R., Montea, M.C., Fuentea, E., Santosb, S.F. &
Negro, C. (2013). Corn Stalk from Agricultural
Residue used as Reinforcement Fiber in Fiber-
Cement Production. Industrial Crops and Products,
43, 832–839. DOI: 10.1016/j.indcrop.2012.08.034
- Kristensen, H.S. & Mosgaard, A. (2020). A review of micro
level indicators for a circular economy–moving
away from the three dimensions of sustainability.
Journal of Cleaner Production, 243, 118531. DOI:
10.1016/j.jclepro.2019.118531
- Naghizadeh, Z., Faezipour, M., Ebrahimi, G. & Hamzeh,
Y. (2011). Fabrication of lignocellulosic fiber–
cement composite board and determination of
optimum quantities of additives. Journal of the
Indian Academy of Wood Science, 8(1), 37. DOI:
10.1007/s13196-011-0021-8
- Nazerian, M. & Sadeghiipanah. V, (2013), Cement-bonded
particleboard with a mixture of wheat straw and
poplar wood. Journal of Forestry Research, 24, 381-
390. DOI: 10.1007/s11676-013-0363-8
- Odeyemi, S.O., Abdulwahab, R., Adeniyi, A.G. & Atoyebi,
O.D. (2020). Physical and mechanical properties of
cement-bonded particle board produced from
African balsam tree (Populous Balsamifera) and
periwinkle shell residues. Results in Engineering, 6,
100126. DOI: 10.1016/j.rineng.2020.100126
- Okino, E.Y.A., De Souza, M.R., Santana, M.A.E., Da
Alves, M.V., De Souza, M.E. & Texeira, D.E.
(2005). Physicomechanical properties and decay
resistance of cupressus ssp. cement-bonded
particleboards. Cement and Concretes Composites,
27, 333-338. DOI:
10.1016/j.cemconcomp.2004.02.046
- Okino, E.Y.A., De Souza, M.R., Santana, M.A.E., Alves,
M.V.D.S., De Sousa, M.E. & Teixeira, D.E.
(2004). Cement-bonded wood particleboard with a
mixture of eucalypt and rubberwood. Cement and
Concretes Composites, 26(6), 729-734. DOI:
10.1016/S0958-9465(03)00061-1
- Papadopoulos, N.A. (2007). An İnvestigation of the
suitability of some greek wood species in wood-
cement composites manufacture. Holz Roh Werkst,
65, 245-246. DOI: 10.1007/s00107-006-0126-8
- Pedieu, R., Koubaa, A., Riedl, B., Wang, X.M. & Deng, J.
(2012). Fire-retardant properties of wood
particleboards treated with boric acid. European
Journal of Wood and Wood Products, 70(1-3), 191-
197. DOI: 10.1007/s00107-011-0538-y
- Qi H, Cooper P.A. & Wan, H. (2006). Effect of carbon
dioxide injection on production of wood cement
composites from waste medium density fiberboard
(MDF). Waste Manage, 26, 509-515. DOI:
10.1016/j.wasman.2005.04.010
- Rana, M.N., Islam, M.N., Nath, S.K., Das, A.K.,
Ashaduzzaman, M. & Shams, M.I. (2020).
Influence of chemical additive on the physical and
mechanical properties of cement - bonded composite
panels made from jute stick. Journal of Building
Engineering, 31, 101358. DOI:
10.1016/j.jobe.2020.101358
- Tabarsa, T. & Ashori, A. (2011) Dimensional stability and
water uptake properties of cement-bonded wood
composites. Journal of Polymers and the
Environment, 19, 518-521. DOI: 10.1007/s10924-
011-0295-3
- Tittelein, P., Cloutier, A. & Bissonnette, B. (2012). Design
of a low-density wood–cement particleboard for
interior wall finish. Cement and Concrete
Composites, 34(2), 218-222. DOI:
10.1016/j.cemconcomp.2011.09.020
- Yel, H., Kalaycioglu, H. & Aras, U. (2017). Utilization of
silica fume in manufacturing of cement bonded
particleboards. Pro Ligno, 13(4), 257-263.
- Yel H, Cavdar, A.D. & Torun, S.B. (2020). Effect of press
temperature on some properties of cement bonded
particleboard. Maderas. Ciencia y tecnología, 22(1),
83-92. DOI: 10.4067/S0718-221X2020005000108
- Yel, H, Aras, U. & Kalaycıoğlu, H. (2022). Utilization of
waste urea-formaldehyde resin-bonded
particleboards in the manufacturing of cement-
bonded particleboards. Giresun ITESDES 2022, 2-5
June, Giresun, Turkey, 411-424 pp.
- Zhengtian, L. & Moslemi, A.A. (1985). Influence of
chemical additives on the hydration characteristics
of tern larch wood-cement water mixtures. Forest
Products Journal, 35(7), 837-843.