___

• 1. Rasmussen, N.W., “New Filling/Feeding Process Produces Vertically-Parted Aluminum Green Sand Castings” Modern Casting, 54-55, April 2000. 2. Kuo, Y.S., Chang, E. and Lin, Y.L., “The Feeding Effect of Risers on the Mechanical Properties of A201 Al Alloy Plate Casting” AFS Transaction, Cilt 89, No 159, 777-782, 1989. 3. Campbell, J. Casting, Butterworth-Heinemann, 120-300, 1999. 4. Güleyüpoğlu, S., “Casting Process Design Guidelines”, AFS Transactions, Cilt 97, No 83, 869-876, 1997. 5. Kuo, J.H., Hsu, F.L. and Hwang, W.S., “Development of an Interactive Simulation System For the Determination of the Pressure- Time Relationship During the Filling in A Low Pressure Casting Process”, Science and Technology of Advanced Materials, Cilt 2, 131-145, 2001. 6. Dash M., and Malkhlouf, M., “Effect of KeyAlloying Elements on the Feeding Characteristics of Aluminum- Silicon Casting Alloys”, Journal of Light Metals, Cilt 1, 251-265, 2001. 7. Li, K.D., Cheng, M.C. and Chang, E., “Effect of Pressure on the Feeding Behavior of A356 Alloy In Low-Pressure Casting” AFS Transaction, Cilt 01, No 026, 311-320, 2001. 8. Lee, Y.W., Chang, E., Lin, Y.L and Yeh, C.H., “Correlation of Feeding and Mechanical Properties of A206 Aluminum Alloy Plate Casting” AFS Transaction, Cilt 90, No 187, 935-941, 1990. 9. Loper Jr, C.R. and Prucha, T.E., “Feed Metal Transfer in Al-Cu-Si Alloys” AFS Transaction, Cilt 90, No 165, 845-853, 1990. 10. Fuoco, R., Correa, E.R. and A. Bastos, M., “Effects of Grain Refinement on Feeding Mecanims in A356 Aluminum Alloy” AFS Transaction, Cilt 98, No 78, 401-409, 1998. 11. Pan, E.N., Lin, C.S. and Loper Jr, C.R., “Effects of Solidification Parameters on the Feeding Efficiency of A356 Aluminum Alloy” AFS Transaction, Cilt 90, No 117, 735-746, 1990. 12. Taylor, J.A., Schaffer, G.B. and StJohn, D.H., “Shrinkage Porosity Formation in Iron Containing Al-Si-Cu-Mg Casting Alloys”, Proc. Inter. Conf. on Casting and Solidification of Light Alloys, Gold Coats, Australia, 55-60, 30-31 August 1995. 13. Xiong, M. and Kuznetsov, A.V., “An Investigation of the Microporosity Formation in An Al-4.1 %Cu Alloy Casting in Microgravity and in Standard Gravity”, Heat and Mass Transfer, Cilt 38, 35-43, 2001. 14. Dahle, A.K. and StJohn, D.H., “Rheological Behaviour of the Mushy Zone and Its Effect on the Formation of Casting Defects During Solidification”, ACTA Metallurgica, Cilt 47, No 1, 31-41, 1999. 15. Knuutinen, A., Nogita, K., McDonald, S.D. and Dahle, A.K., “Porosity Formation in Aluminum Alloy A356 Modified with Ba, Ca, Y and Fb” Journal of Light Metals, Cilt 1, 241-249, 2001. 16. Niu, X.P., Hu, B.H., Pinwill, I. and Li, H., “Vacuum Assisted High Pressure Die Casting of Aluminium Alloys”, Journal of Materials Processing Technology, Cilt 105, 119-127, 2000. 17. Anon, “Turning the Gating World Upside Down”, Technical Paper, Hitchiner Manufacturing Co., (www.hitchiner.com), 2005. 18. Ripkin, F. and Lipson, S., “Counter Gravity Casting of Aluminum Alloys in Green Sand Molds” AFS Transactions, Cilt 70, 581-592, 196). 19. Lipson, S. and Ripkin, F., “Effect of Sections Thickness on the Tensile Properties of Thin- Section Aluminum Alloy Sand Casting” AFS Transactions, Cilt 69, 192-197, 1969. 20. Chandley, G.D., “Making Casting Without Ladles or Sprues – The CLA Process” AFS Transactions, Cilt 28, 37-42, 1976. 21. Shenefelt, J.R. and others, “Countergravity Casting of Thin-Wall Al A356, Part II: Result of Casting Characterization Studies” AFS Transactions, Cilt 101, 563-566, 1998.