DOĞAL YOL İLE HAVALANDIRILAN BİR SANAYİ KURULUŞUNDA ISIL KONFOR ĠNCELEMESĠ VE GĠYSĠ FAKTÖRÜ, METABOLĠK ORAN, ÇALIŞAN AĞIRLIĞININ KONFORA ETKİLERİNİN ARAŞTIRILMASI

Bu çalışmada otomotiv sektöründeki firmanın termal konfor şartları ve çalışan kilosu, giysi yalıtım faktörü, metabolik oranın termal konfor üzerinde etkilerini incelenmiştir. Konfor ölçümleri 6 bölümde yapılmıştır. Ölçümlerin yapıldığı bölümler kalıphane, kaynak, pres, boya, montaj ve boyahane bölümleridir. Ölçümler DELTA OHM 52.1 marka ekipmanlar ve yazılımı ile yapılmıştır. Giysi faktörü ölçümlerde 0,8 clo olarak alınmıştır. Metabolik oran değerleri bölümlerine bağlı olarak düşük 100 W/m2 ve orta 135 W/m2 değerler olarak kabul edilmiştir. Giysi faktörü etkisinin incelenmesinde değerler 0,5, 0,6, 0,7, 0,8, 0,9, 1 clo olarak seçilmiştir. Çalışma sonucunda fabrika içinde termal konfor bakımından en iyi ve kötü bölümün sırasıyla lojistik ve kalıphane olduğu tespit edilmiştir. Çalışanların düşük giysi faktörü değerlerinde özellikle iş yoğunluğunun yüksek olmadığı sabah saatlerinde ortamı daha konforlu hissettikleri görülmüştür. Çalışmada dikkate değer bir sonuç olarak ağırlığı 80 kg’ın üzerindeki kişilerin ortamı daha sıcak hissettikleri yapılan anket sonucu belirlenmiştir. Yüksek metabolik oranda çalışan kişilerin düşük metabolik oran gerektiren işlerle değişimli çalışmasının konfor hissi bakımından önemli olduğu tespit edilmiştir.

Thermal Comfort Examination in an Industrial Establishment Ventilated Naturally and Investigation of the Effects of Clothing Factor, Metabolic Rate, Comfort of Working Weight

In this study, the thermal comfort conditions of the company in the automotive sector and the effects of working weight, clothing factor, metabolic rate on thermal comfort were investigated. Thermal comfort measurements were done in 6 divisions. The divisions that the measurements were done are molding, welding, pressing, dye house, assembling and logistic. The measurements were done via DELTA OHM 52.1 labeled equipments and software. The clothing factor is taken as 0,8 clo during measurements. Metabolic rates varies between low 100 W/m2 and medium 135 W/m2 ratios depending to their divisions. During examination of the clothing factor, the rates were selected as 0,5, 0,6, 0,7, 0,8, 0,9, 1 clo. As a result of the study, it was determined that the best and worst thermal comfort in the factory are respectively logistics and molding. On low ratio clothing factor, employees feel more snug especially during morning hours as workload is not high was seen. During the research, the people whose weight are over 80 kg. feel surrounding much more hot was determined as significant finding as the conclusion of survey. The importance of alternate shift between the employees work with high metabolism ratio and the employees work with low metabolism ratio ascertained.

PDF

___

Ansi/Ashrae. (2004). Thermal Environmental Conditions for Human Occupancy. Ashrae, 2004, 30.
Atmaca, I., Kaynakli, O., & Yigit, A. (2007). Effects of radiant temperature on
thermal comfort. Building and Environment, 42(9), 3210–3220. doi:10.1016/j.buildenv.2006.08.009
ANSI/ASHRAE Standard, (2004). Ventilation for Acceptable Indoor Air Quality. ANSI/ASHRAE Addendum N to 62-2001, 8400.
Bridger RS. (2003). Introduction to ergonomics (2nd Edition). London: Taylor & Francis, London and Newyork.
Budd, G. M. (2008). Wet-bulb globe temperature (WBGT)—its history and its limitations. Journal of Science and Medicine in Sport, 11(1), 20–32, doi:10.1016/j.jsams.2007.07.003
Epstein, Y., & Moran, D. S. (2006). Thermal comfort and the heat stress indices. Industrial Health, 44(3), 388–398, doi: 10.2486/indhealth.44.388
Epstein, Y., & Roberts, W. O. (2011). The pathopysiology of heat stroke: an integrative view of the final common pathway. Scandinavian Journal of Medicine and Science in Sports, 21(6), 742–748, doi:10.1111/j.1600-0838.2011.01333.x
Fanger, P. O. (1970). Thermal comfort : analysis and applications in environmentalengineering. McGraw-Hill, New York:
Fisk, W. J., & Rosenfeld, A. H. (1997). Estimates of Improved Productivity and Health from Better Indoor Environments. Indoor Air, 7(3), 158–172. doi:10.1111/j.1600-0668.1997.t01-1-00002.x
Fox, W. . (1967). Human Performance in the Cold. The Journal of the Human Factors and Ergonomics, 9(3), 203–220, doi: 10.1177/001872086700900302
Guan, Y., Jones, B.W., Mohammad H. Hosni, Gielda, T. P. (2003). Literature Review of the Advances in Thermal Comfort Modeling. ASHRAE Transactions, 3(109), 908–916.
Hales JRS, R. D. (1987). Heat stress-physical exertion and environment. Excerpta Medica, Amsterdam.
Ho, S. H., Rosario, L., & Rahman, M. M. (2009). Thermal comfort enhancement by using a ceiling fan. Applied Thermal Engineering, 29(8–9), 1648–1656. doi:10.1016/j.applthermaleng.2008.07.015
Holm, D., & Engelbrecht, F. A. (2005). Practical choice of thermal comfort scale and range in naturally ventilated buildings in South Africa. Journal of the South African Institution of Civil Engineering, 47(2), 9–14.
HSE. (1999). Thermal comfort in the workplace: Guidance for employers, Health & Safety Executive
Ismail, A. R., Jusoh, N., Makhtar, N. K., Daraham, M. R., Parimun, M. R., & Husin, M. A. (2010). Assessment of Environmental Factors and Thermal Comfort at Automotive Paint Shop. Journal of Applied Sciences, 10(13), 1300–1306, doi: 10.3923/jas.2010.1300.1306
Ismail, A. R., Karagaratnan, S. K., & Kadirgama, K. (2013). Thermal comfort findings: Scenario at Malaysian automotive industry. Thermal Science, 17(2), 387– 396, doi:10.2298/TSCI1111110151
ISO 7730 International Standard. (1994). Moderate thermal environments - Determination of the PMV and PPD indices and specification of the conditions for thermal comfort.
Kerslake, M. D. (1972). The Stress of Hot Environments. Cambridge University Press, London.
Kjellstrom, T., Holmer, I., & Lemke, B. (2009). Workplace heat stress, health and productivity - an increasing challenge for low and middle-income countries during climate change. Global Health Action, 2(Special Issue), doi:10.3402/gha.v2i0.2047
Lemke, B., & Kjellstrom, T. (2012). Calculating Workplace WBGT from Meteorological Data: A Tool for Climate Change Assessment. Industrial Health, 50(4), 267–278, doi:10.2486/indhealth.MS1352
Malchaire, P. J. (2004). Ergonomics of the thermal environment Determination of metabolic rate, 3, 1–14, doi: 10.3403/03205220
McIntyre, D. A. (1980). Indoor Climate. London, Elsevier, United Kingdom
One, P. (2003). Table of of contents, (November), 1–85. doi:10.1002/ejoc.201200111
Orosa, J. A., & Oliveira, A. C. (2010). Assessment of work-related risk criteria onboard a ship as an aid to designing its onboard environment. Journal of Marine Science and Technology, 15(1), 16–22, doi:10.1007/s00773-009-0067-0
Parsons, K. (2006). Heat stress standard ISO 7243 and its global application. Industrial Health, 44(3), 368–379, doi:10.2486/indhealth.44.368
Parsons, K. . (1993). Human Thermal Environments. Taylor & Francis, London.
Parsons, K. C. (2000). Environmental ergonomics: A review of principles, methods and models. Applied Ergonomics, 31(6), 581–594, doi:10.1016/S0003-6870(00)00044-2.
Pfafferott, J., Herkel, S., & Wapler, J. (2005). Thermal building behaviour in summer: Long-term data evaluation using simplified models. Energy and Buildings, 37(8), 844–852, doi:10.1016/j.enbuild.2004.11.007.
Pilcher, J. J., Nadler, E., & Busch, C. (2002). Effects of Hot and Cold Temperature Exposure on Performance: a Meta-Analytic Review. Ergonomics, 45(10), 682–698. doi:10.1080/00140130210158419.
Predicting Thermal Comfort Fanger Comfort Analysis. (n.d.). Retrieved from http://ceae.colorado.edu/~brandem/aren3050/docs/ThermalComfort.pdf
Ramsey, J. D. (1995). Task performance in heat: a review. Ergonomics, 38(1), 154– 165, doi:10.1080/00140139508925092.
Ramsey, J. D., Burford, C. L., Beshir, M. Y., & Jensen, R. C. (1983). Effects of workplace thermal conditions on safe work behavior. Journal of Safety Research, 14(3), 105–114, doi:10.1016/0022-4375(83)90021-X.
Yamankaradeniz, R., Horuz, İ., Coşkun, S., Kaynaklı, Ö., Yamankaradeniz, N., (2008). İklimlendirme Esasları ve Uygulamaları, Dora Yayıncılık, Bursa.
Shikdar, A. A., & Sawaqed, N. M. (2003). Worker productivity, and occupational health and safety issues in selected industries. Computers and Industrial Engineering, 45(4), 563–572. https://doi.org/10.1016/S0360-8352(03)00074-3
Skoog, J., Fransson, N., & Jagemar, L. (2005). Thermal environment in Swedish hospitals: Summer and winter measurements. Energy and Buildings, 37(8), 872– 877, doi: 10.1016/j.enbuild.2004.11.003.
TS EN 27243. (2002). Sıcak ortamlar - Wbgt (yaş - Hazne küre sıcaklığı) indeksine göre ısının çalışan üzerindeki baskısının tahmini, Türk Standartları Enstitüsü,Ankara.
Zhang, L. Z., & Niu, J. L. (2003). Indoor humidity behaviors associated with decoupled cooling in hot and humid climates. Building and Environment, 38(1), 99– 107, doi:10.1016/S0360-1323(02)00018-5.