Maximization of Sewing Strength and Minimization of Seam Pucker for Denim Fabrics Using Taguchi Method

Seams provide the shape of the garments and support the fabric pieces together. The seam quality is important for the serviceability of any garment. In general, the seam quality depends on various factors such as fabric weight, sewing thread type, and stitches per unit area. In this research, three different levels of fabric types with the same construction and different weights, which are mostly used in the production of denim products, were examined. For this purpose, each fabric was sewn in the warp direction with three different levels of sewing threads and three different levels of stitch densities. Then, the values of seam strength, and the seam pucker values were obtained with three replications for each combination of levels. In this study, it is aimed to obtain the optimum levels of fabric weight, sewing thread type, and stitch density of denim fabrics by using the Taguchi method. Custom Taguchi Design is employed to observe the efficiency of factor levels on seam strength and seam pucker, and existence of interactions among fabric weight, sewing thread type, and stitch density.

Keywords:

Seam quality, seam strength, seam efficiency, denim fabric Taguchi method.,

PDF

___

1. Akcagun, E., Ceviz, N.Ö., Yılmaz, A. and Mazari, A., (2017), “Analyzing the effects of special washing processes on characteristics of sewing threads”, The Journal of The Textile Institute, Vol. 108, No. 11, pp. 1926–1932.
2. Haghighat, E., Etrati, S.M., Najar, S.S., (2014), “Evaluation of Woven Denim Fabric Sewability based on Needle Penetration Force”, Journal of Engineered Fibers and Fabrics, Vol. 9, No. 2, pp. 47-60.
3. Eryuruk, H. S., (2019), “The effects of elastane and finishing processes on the performance properties of denim fabrics”, International Journal of Clothing Science and Technology, Vol. 31, No. 2, pp. 243-258.
4. Behera, B.K., Chand, S., Singh, T.G. and Rathee, P., (1997), “Sewability of denim”, International Journal of Clothing Science and Technology, Vol. 9, No. 2, pp. 128-140.
5. Malek, S., Jaouachi, B., Khedher, F., Said, S.B. and Cheikhrouhou, M., (2017), “Influence of some sewing parameters upon the sewing efficiency of denim fabrics”, The Journal of The Textile Institute, Vol. 108, No.12, pp. 2073-2085.
6. Rajpu, B. et. al., (2018), “Effect of sewing parameters on seam strength and seam efficiency”, Trends in Textile Engineering & Fashion Technology, Vol. 4, No.1, pp.1-5.
7. Hayes, S. and Mcloughlin, J. (2013), “The sewing of textiles”, in Jones, I. and Stylios, G.K. (Eds), Joining Textiles Principles and Applications, Woodhead Publishing Series in Textiles, No. 110, pp. 62-122.
8. Mandal, S. and Abraham, N. (2010), “An overview of sewing threads mechanical properties on seam quality”, Pakistan Textile Journal, Vol. 59, No.1, pp. 40-43.
9. Bharani, M. and Mahendra Gowda, R.V. (2012), “Characterization of seam strength and seam slippage on pc blend fabric with plain woven structure and finish”, Research Journal of Recent Sciences, Vol. 1, No. 12, pp. 7-14.
10. Hossain, A. et. al, (2020), “Effect of Different Sewing Parameters on Lockstitch Seam Strength for Denim Fabric”, Journal of Engineering Advancements, Vol. 1, No. 4, pp 139-143.
11. Germanova-Krasteva, D. and Petrov H, (2008), “Investigation on the seam’s quality by sewing of light fabrics” International Journal of Clothing Science and Technology, Vol. 20, No. 1, pp. 57-64.
12. Malek, S., Khedher, F., Jaouachi, B. and Cheikhrouhou, M., (2019), “Influence of denim fabric properties and sewing parameters upon the seam slippage and seam quality prediction”, Journal of Textile and Apparel, Technology and Management, Vol. 11, No.1, pp. 1-17.
13. Tuteja, S. and Sen, P., (2019), “Influence of stitch density and sewing thread count on the seam performance of denim fabric”, Journal of The Textile Association, Vol. 9, No. 2, pp. 442-448.
14. Yildiz, E.Z. (2018), Modeling of Seam Quality by Using Different Seam Parameters, Ege University, Turkey, PhD Thesis.
15. Tiber, B. and Yilmaz, N., (2022), “Investigation of the effects of elastic sewing thread on seam performance properties of stretch denim fabrics”. Tekstil ve Konfeksiyon, Vol. 32, No. 1, pp. 47-56.
16. Ateş, M., Gurarda, A. and Ceven, K., (2019), “Investigation of seam performance of chain stitch and lockstitch used in denim trousers”, Tekstil ve Mühendis, Vol. 26, No. 115, pp. 263-270.
17. Sarkar, J., Al Faruque, A. and Mondal, M.S., (2021), “Modeling the seam strength of denim garments by using fuzzy expert system”, Journal of Engineered Fibers and Fabrics, Vol. 16, pp. 1-10.
18. Nayak, R. and Padhye, R., (2013), Sewability of Air-Textured Sewing Threads in Denim”, Journal of Textile and Apparel, Technology and Management, Vol.8, No.1, pp. 1-11.
19. Ross, J. E. (1999). Total Quality Management (3rd edition). ABD: St. Lucie Press
20. Canyılmaz, E. ve Kutay, F. (2003). Taguchi Metodunda Varyans Alnalizine Alternatif Bir Yaklaşım, Gazi Üniversitesi Mühendislik Mimarlık Dergisi, Cilt 18, No:3, pp. 51-63
21. Taguchi,G. ve Clausing,D. (1990) Robust Quality, Hardward Business Review, pp. 65-76.
22. Rowlands, H., Antony, J. ve Knoles, G. (2000). An Application of Experimental Design for Process Optimization. The TQM Magazine, Vol.12, No.2, pp. 78-83.
23. Ustuntag, S. and Turksoy, H.G., (2019), “Optimization of coating parameters for air permeability of denim fabrics through Taguchi method”, Industria Textila, Vol. 70, No. 3, pp. 259-264.
24. Onal, L., Zeydan, M., Korkmaz, M. and Meeran, S., (2009), “Predicting the seam strength of notched webbings for parachute assemblies using the Taguchi's design of experiment and artificial neural networks”, Textile Research Journal, Vol. 79, No. 5, pp. 468–478.
25. Almetwally, A.A., (2020), “Multi-objective Optimization of Woven Fabric Parameters Using Taguchi–Grey Relational Analysis”, Journal of Natural Fibers, Vol. 17, No. 10, pp. 1468-1478.
26. Hossain, I., Hossain A., and Choudhury, I.A., (2016), “Dyeing process parameters optimisation and colour strength prediction for viscose/lycra blended knitted fabrics using Taguchi method”, The Journal of The Textile Institute, Vol. 107, No. 2, pp. 154–164.
27. Ghosh, A., Mal, P., Majumdar, A. and Banerjee, D, (2017), “An investigation on air and thermal transmission through knitted fabric structures using the Taguchi method”, AUTEX Research Journal, Vol. 17, No 2, pp. 152-163.
28. Ghani, S.A. and Gong, H., (2010), “Seam quality: experimental and modelling works using the structural equation methodology”, Scientific Research Journal, Vol. 7, No. 1, pp. 13-36.
29. Hati, S. and Das, B.R., (2011), “Seam Pucker in Apparels: A Critical Review of Evaluation Methods”, Asian Journal of Textile 1, 60-73, https://doi.org/10.3923/ajt.2011.60.73
30. Myers, R.H., Montgomery, D.C., Anderson, C.M., (2009), Response Surface Methodology: Process and Product Optimization Using Designed Experiments, John Wiley&Sons, Inc., New Jersey.
31. Hines W.W. and Montgomery, D.C., (1990), Probability and Statistics in Engineering and Management Science, third edition, John Wiley and Sons, New York.

ISSN: 1300-3356
Yayın Aralığı: Yılda 4 Sayı
Yayıncı: Ege Üniversitesi Tekstil ve Konfeksiyon Araştırma & Uygulama Merkezi

Arşiv