An investigation into the performance of hss drills when drilling commercially pure molybdenum
The use of commercially available molybdenum materials, which exhibit good mechanical and thermal properties, has been increasing day by day, and therefore their machinability has become important. Due to their good mechanical properties, shaping of these materials through machining methods causes some problems such as rapid tool wear, low surface quality and tool breakage. Besides, the determination of the machining conditions and methods of these materials which are quite expensive compared to other metals and alloys is very important in terms of improving the machined part quality and reduced costs. In this study, it is aimed to determine optimum cutting conditions in drilling of molybdenum of commercial purity using high speed steel (HSS) drill bits. For this purpose, experimental studies were carried out to reveal the effect of cutting parameters on surface roughness, drill bit wear, deviation on hole diameter, cylindricity error and drill bit temperature. It is seen from the experimental results that the drill bit failed quickly when drilling over 40 m/min. Significantly high surface roughness values are obtained nearly at all the conditions. As the cutting speed and feed rate increase, the drill bit temperature increases.
Keywords:
Molybdenum, drilling wear, dimensional and geometric tolerances, temperature.,
___
- [1] Ghoniem NM., (1998) Assesment of high-temperature refractory metals, UCLA-Apex meeting, 1-76.
- [2] Rowe D., (2003) Refractory metals in heat treating/thermal equipment, Brentwood United Kingdom, 56-60.
- [3] Walser HA., Shields J., (2007) Traditional and emerging applications of molybdenum metal and its alloys, International Molybdenum Association, IMOA Newsletter, 1-16.
- [4] İnternet (2015) Molybdenum, Plansee web. https://www.plansee.com/en/materials/molybdenum.html.
- [5] İnternet (2015) Designation: B387-10, Standart specification for molybdenum and molybdenum alloy bar, rod and wire, ASTM International web. https://www.astm.org/Standards/B387.htm.
- [6] İnternet (2017) General guide to machining molybdenum and molybdenum alloy, ED Fagan Inc. web. http://www.edfagan.com/litPDF/Machining_Guide_Molybdenum_Moly_Alloys.pdf.
- [7] Zlatin N., Field M., Gould J., (1963) Machining of refractory materials, Armed Services Technical Information Agency, ASD Interim Report Unclassifield 7-532a(IX), Virginia.
- [8] Sortino M., Totis G., Prosperi F., (2013) Dry turning of sintered molybdenum, Journal of Materials Processing Technology, 213, 1179-1190.
- [9] Kuljanic E., Sortino M., Totis G., (2010) Machinability of Difficult Machining Materials, 14th International Research/Expert Conference-Trends in the Development of Machinery and Associated Technology, Mediterranean Cruise.
- [10] Shields, J.A., (2013) Applications of molybdenum metal and its alloys, IMOA, 1-44.
- [11] Gökçe H., Çiftçi İ., Demir H., (2018) Cutting parameter optimization in shoulder milling of commercially pure molybdenum, Journal of the Brazilian Society of Mechanical Sciences and Engineering, 40, 360.
- [12] Çiftçi İ., (2005) Östenitik paslanmaz çeliklerin işlenmesinde kesici takım kaplamasının ve kesme hızının kesme kuvvetleri ve yüzey pürüzlülüğüne etkisi, Journal of the Faculty of Engineering and Architecture of Gazi University, 20, 205-209.
- [13] Trent EM., Wright PK., (2000) Metal Cutting 4th Edition, Butterworth Heinemann.
- ISSN: 1304-7191
- Yayın Aralığı: Yılda 4 Sayı
- Yayıncı: Yıldız Teknik Üniversitesi