THE CHARACTERIZATION OF FRONT CUTTING GEOMETRY AND SURFACE PROPERTIES IN ABRASIVE WATER JET CUTTING OF ALUMINUM ALLOY MATERIALS

It has been compulsory to use unusual machining methods, against the developments in the manufacturing sector. The Abrasive Water Jet (AWJ) method is the least known and common one. Unknown aspects of the method makes limited use. The AWJ method shows various surface roughness values depend on the cutting depth although capable of cutting all kinds of materials. So that caused to adversely affected the widespread use of the method. The cutting front geometry consists to opposite direction of the feeding is another negative ways beside on the adversely effects on the cut surface properties on workpiece. In this study, the modelling of cutting front geometry was considered to provide a positive impact on expand the usability of AWJ methods. The aluminum alloys were used as workpiece regarding an uneasy machining material for AWJ and the experimental results were evaluated.

Keywords:

Abrasive waterjet, cut front geometry, surface properties surface roughness,

PDF

___

[1] Steinhauser, T. J., “Abrasive water jets on the cutting edge of technology”, Flow Systems, USA, (1989).
[2] A. Akkurt, “Çeşitli malzemelerin Aşındırıcı Su Jeti İle Kesilmesinde Yüzey Özellikleri, Sertlik ve Mikro yapı Değişimlerinin Farklı Kesme Yöntemleriyle Karşılaştırmalı Olarak İncelenmesi”, Doktora Tezi, Gazi Üniversitesi Fen Bilimleri Enstitüsü, Ankara, (2002).
[3] Niu, M., Fukunishi, Y., Sawamura T., “Control of striated roughness on the surface cut by abrasive water jet”, BHR Group Jetting Technology, pp. 769-777 Ishinomaki Senshu University, Japan, (1996).
[4] Momber, A. W., Kovacevic, R., Schüneman, R., et al, “The influence of abrasive grain size distribution parameters on the abrasive water jet machining process”, In: Rajukar KP (ed) 1996 Proc. 25 th North American Manuf. Engrs , Dearborn , pp 21-26, (1996).
[5] Mozurkiwicz, M., Fincuan, L., Ferguson, R., “Investigation of abrasive cutting head internal parameters” , In.:Woods P A (ed) 1988 Proc..9 th. Int. Symp. Jet Cutting Techn, BHRA Fluid Engng Cranfield, (1988).
[6] Ohlsson, L., “The theory and practice of abrasive water jet cutting”, PhD Thesis, Lulea University of Technology, Sweden, (1995).
[7] Juo, N. S., Louis, H., Meier, G., “Surface structure and kerf geometry in abrasive water jet cutting: formation and optimization”, Proceedings of the7th American Waterjet Conference, USA, 1 – 26 (1993).
[8] Orbanic, H. Junkar, M. “Analysis of striation formation mechanism in abrasive water jet cutting” Wear Volume 265, Issues 5–6, 25 August 2008, Pages 821–830.
[9] Maros, Z., “Energy Approach of the Taper at Abrasıve Waterjet Cuttıng” Production Processes and Systems, vol. 6. (2013) No. 1. pp. 89-96.
[10] Kong, M. C., Axinte, D., “Response of titanium aluminide alloy to abrasive waterjet cutting: geometrical accuracy and surface integrity issues versus process parameters” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 2009 Volume 223: 19-42.
[11] Singh, P. L., Chen, W.L., Munoz, I., “Comprehensive evaluation of abrasive waterjet cut surface quality”, 6th American Water Jet Conference, pp. 139-161, Houston, USA, (1991).
[12] Akkurt, A., “Cut Front Geometry Characterization in Cutting Applications of Brass with Abrasive Water Jet” Journal of Materials Engineering and Performance Volume 19(4) June 2010—599.
[13] Akkurt, A., “The Cutting Front Side Geometry in The Applications of D3 Cold Work Tool Steel Material Via Abrasive Water Jet”, Gazi University Journal of Science, Vol 26, No 2 pp. 225-239 (2013).
[14] Blickwedel, H., Guo, N. S., Haferkamp, H., Louis, H., “Prediction abrasive jet cutting performance and quality”, Proceedings of 9th International Symposium on Jet Cutting Technology, pp.163-179, BHRA, Fluid Engineering Centre, UK, (1990).
[15] Momber, A., Kovacevic, R., “Calculation of exit jet energy in abrasive water jet cutting”, ASME, Manufacturing Science and Engineering, 361-366, USA, (1994).
[16] Hashish, M., “Optimization factors in abrasive-waterjet machining”, Journal of Engineering for Industry, Vol. 113. pp132-139, (1991).
[17] Momber, A., Kovacevic, R., “Calculation of exit jet energy in abrasive water jet cutting”, ASME, Manufacturing Science and Engineering, 361-366, USA, (1994).
[18] Hashish, M., “A modeling study of jet cutting surface finish”, PED–Vol. 58, pp.151-167, (1992).
[19] Murai, H., Nishi, S., 1989, “Structure of Waterjet and Erosion of Materials” Proceedings of the 5th American Waterjet Conference, pp 29-31, Toronto, Canada.
[20] Niu, M. S., Kobayashi, R., Yamaguchi, T., 1995, “Kerf Wıdth ın Abrasive Waterjet Machining”, Department of Machine Intelligence and Systems.
[21] Hashish, M., “Caracteristics of surfaces machined with abrasive water jet”, Journal of Eng. Mat. And Tech., Vol. 113, pp.354-362, (1991).
[22] Zeng. J., Hines. R., Kim. T. J., “Characterization of energy dissipation Phenomena in abrasive water jet cutting”, Proceeding of the 6th American Water Jet Conference, pp. 163-177, Water Jet Technology Association, USA. (1991).
[23] Momber, A., “A simplified mathematical energy dissipation model for water jet and abrasive water jet cutting processes”, 8th Amer. Water Jet Conference, August 26 – 29, Houston, 829 – 843, (1995).
[24] Momber, A., Kovacevic, R., “Calculation of exit jet energy in abrasive water jet cutting”, ASME, Manufacturing Science and Engineering, 361-366, USA, (1994).
[25] Zeng. J., Hines. R., Kim. T. J., “Characterization of energy dissipation Phenomena in abrasive water jet cutting”, Proceeding of the 6th American Water Jet Conference, pp. 163-177, Water Jet Technology Association, USA. (1991).
[26] Hashish, M., 1984, “On the Modeling of Abrasive Waterjet Cutting”, Proc. Of Seventh Int. Symposium on Jet Cutting Technology, Paper No El, BHRA Fluid Engineering, Ottawa, Canada.
[27] Tan, D. K. M., 1986, “A Model for The Surface Finish in Abrasive Waterjet Cutting”, Proceedings of 8th International Symposium on Jet Cutting Technology, pp. 31-38, England.

Sigma Mühendislik ve Fen Bilimleri Dergisi-Cover

ISSN: 1304-7191
Yayın Aralığı: Yılda 4 Sayı
Yayıncı: Yıldız Teknik Üniversitesi

Arşiv