Production and Characterization of Carbon-Kevlar-Aramid Reinforced Layer Composites with VARTM Method

In this study, laminated composite materials are produced by Vacuum Assisted Resin Transfer Molding (VARTM) Method. Three different reinforcement materials (carbon, kevlar and aramid) are used in the production phase. Tensile test is applied to the samples after the production and in the light of SEM images; fractured surfaces of the samples and their results are evaluated.

PDF

___

URL-2. 2017. “http://www.kompozit. net/pinfo.asp?pid=287&diger=tumu.” Retrieved April 25, 2017 (http://www.kompozit.net/).

Addington, Michelle and Daniel L. Schodek. 2005. Smart Materials and Technologies in Architecture. Retrieved April 25, 2017 (https://bintian. files.wordpress. com/2013/01/smart-materials-newtechnologies- for-the architecture-design professions. pdf).

URL-1. 2017. “http://www.bilgiustam. com/kompozit-Malzemeler-Hakkında - Hersey/.” Retrieved April 25, 2017 http://www.bilgiustam.com/?s=kompozit+ malzemeler.

Ismail, Durgun, Vatansever Onur, Ertan Rukiye, and Yavuz Nurettin. 2014. “The Effect of Production Technique on Mechanical Properties of Polymer Based Fiber Reinforced Composite Materials. 7 th Automotive Technologies Congress.

Gu, Yizhuo, Xuelin Tan, Zhongjia Yang, Min li, and Zuoguang Zhang. 2014. “Hot Compaction and Mechanical Properties of Ramie Fabric/epoxy Composite Fabricated Using Vacuum Assisted Resin Infusion Molding.” Materials and Design 56:852–61. Retrieved (http://dx.doi.org/10.1016/j.matdes.2013.11 .077).

Zhang, Kaomin, Yizhuo Gu, Min li, and Zuoguang Zhang. 2014. “Effect of Rapid Curing Process on the Properties of Carbon Fiber/epoxy Composite Fabricated Using Vacuum Assisted Resin Infusion Molding.” Materials and Design 54:624–31. Retrieved (http://dx.doi.org/10.1016/j.matdes.2013.08 .065).

Ismail, Durgun, Vatansever Onur, Ertan Rukiye, and Yavuz Nurettin. 2013. “The Experimental Comparison of Composite Parts Manufacturing Methods Used in Automotive Sector sel, 2nd National Aegean Composite Materials Symposium.

Wang, Changchun, Guangquan Yue, Guanghui Bai, Lijian Pan, and Boming Zhang. 2016. “Compaction Behavior and Permeability Property Tests of Preforms in Vacuum-Assisted Resin Transfer Molding Using a Combined Device.” Measurement: Journal of the International Measurement Confederation 90:357–64. Retrieved (http://dx.doi.org/10.1016/j.measurement.2 016.04.058).

Balikoglu, Fatih, Akin Atas, and Nurettin Arslan. 2012. “Application of Vacuum Infusion and Composite Production Method in Yacht and Boat Manufacturing.” pp. 480– 95 in 3rd National Design Manufacturing and Analysis Congress.

Sevkat, Ercan and Malek Brahimi. 2011. “The Bearing Strength of Pin Loaded Woven Composites Manufactured by Vacuum Assisted Resin Transfer Moulding and Hand Lay-up Techniques.” Procedia Engineering 10:153–58. Retrieved (http://dx.doi.org/10.1016/j.proeng.2011.04. 028).

Ismail Durgun. 2013. “Production of Carbon Fiber Engine Hood with Vacuum Infusion Method in II. National Aegean Composite Materials Symposium.