Inconel 718 süper alaşımın plazma ark kaynak yöntemi ile birleştirilmesinde akım şiddetinin etkisi
Bu çalışmada Havacılık ve Nükleer enerji sektöründe sıklıkla kullanılmakta olan Nikel bazlı Inconel 718 süper alaşımı plazma Kaynağı ile birleştirilmiştir ve birleştirme işleminde 130-140-160-180 ve 200 A olmak üzere beş farklı akım kullanılarak akım şiddetinin kaynaklı birleştirme üzerindeki etkisi incelenmiştir. Yapılan kaynak işleminde ilerleme hızı 0,1 m/dk ve gaz debisi ise 0,5 lt/dk. Olarak sabit tutulmuş olup, kaynak işlemi numunelerin sadece tek yüzeyine uygulanmıştır. Kaynak işlemi sonrasında numunelere çekme testi uygulanmış ve mikrosertlik ölçümleri yapılmıştır. Yapılan çalışma sonucunda numunelerin birleşme noktalarında akım şiddetinin artması ile birlikte nüfuziyetin ve çekme mukavemetinin arttığı sertlik değerlerinin ise akım şiddetinden etkilenmediği gözlemlenmiştir.
The Effect of current ıntensity on joining the Inconel 718 super alloy with the plasma arc welding method
In this study, Nickel-based Inconel 718 super alloy, which is frequently used in aerospace and nuclear energy, is combined with Plasma Welding Method. The effect of current density was investigated by using five different currents 130-140-160-180 and 200A in the coupling process. The speed of progress of the welding process is 0,1 m / min and gas flow is 0,5 lt / min. and the welding process is applied to only one surface of the sample. Tensile tests were applied to the samples and microhardness measurements were made after welding. As a result of the study, it was observed that the penetration with increasing current intensity at the junction points of the samples and the hardness values with increasing tensile strength were not affected by the current intensity.
___
- H. Dinç, “Inconel 718 süperalaşımının
termokimyasal borlanması,” Yüksek Lisans
Tezi, 2013.
- ASM Handbook Vol. 6(A), “Welding
fundamentals and processes,” 2011.
- M. Kılıç, “Aısı 304 paslanmaz çeliği ve
1040 çelik çifti’nin plazma kaynak
yöntemiyle birleştirilebilirliğinin
araştırılması,” Yüksek Lisans Tezi, 2008.
- T. Gürgenç and C. Özel, “PTA yöntemi
kullanılarak fecrc , feb ve few alaşımlarıyla
kaplanan aısı 1020 çeliğinin mikroyapı ve
mekanik özelliklerinin araştırılması,” Fırat
Üniversitesi Mühendislik Bilim. Derg., vol.
28, no. 2, pp. 221–232, 2016.
- J.-P. Choi et al., “Densification and
microstructural investigation of Inconel
718 parts fabricated by selective laser
melting,” Powder Technol., vol. 310, pp.
60–66, 2017.
- R. Damodaram, S. R. . Ganesh, and K. R.
Prasad, “Effect of post-weld heat
treatments on microstructure and
mechanical properties of friction welded
alloy 718 joints,” Mater. Des., vol. 53, pp.
954–961, 2014.
- K. D. Ramkumar et al., “Influence of filler
metals and welding techniques on the
structure-property relationships of Inconel
718 and AISI 316L dissimilar weldments,”
Mater. Des., vol. 62, pp. 175–188, 2014.
- Y. Mei et al., “Effect of base metal and
welding speed on fusion zone
microstructure and HAZ hot-cracking of
electron-beam welded Inconel 718,”
Mater. Des., vol. 89, pp. 964–977, 2016.
- K. D. Ramkumar et al., “Studies on the
weldability, microstructure and mechanical
properties of activated flux TIG weldments
of Inconel 718,” Mater. Sci. Eng. A, vol.
639, pp. 234–244, 2015.
- X. You et al., “Effect of solution heat
treatment on the precipitation behavior and
strengthening mechanisms of electron
beam smelted Inconel 718 superalloy,”
Mater. Sci. Eng. A, vol. 689, pp. 257–268,
2017.
- J. Chen and C. Pan, “Welding of Ti-6Al-
4V alloy using dynamically controlled
plasma arc welding process,” Trans.
Nonferrous Met. Soc. China, vol. 21, pp.
1506–1512, 2011.
- C. M. Lin and C. H. Lu, “Effects of
tempering temperature on microstructural
evolution and mechanical properties of
high-strength low-alloy D6AC plasma arc
welds,” Mater. Sci. Eng. A, vol. 676, pp.
28–37, 2016.
- H. Dikbaş, “Tİ6AL4V/Tİ6AL4V malzeme
çiftinin pta kaynağında kaynak bölgesinin
incelenmesi,” Doktora Tezi, 2012.
- D. W. J. Tanner, “Welded Inconel 718 At
High Temperature,” PhD thesis, 2009.