Nikel esaslı süperalaşımların ve titanyum alaşımlarının işlenebilirliği III. bölüm: Kübik bor nitrür (CBN) kesici takımların performanslarının değerlendirilmesi

Bu çalısmada, nikel esaslı süperalasımların ve titanyum alasımlarının farklı operasyonlarla islenmesinde kübik bor nitrür (CBN) takımların performansları son on yılda yapılan çalısmalar incelenerek değerlendirilmistir. Çalısmanın amacı, endüstride yoğun olarak kullanılan bu malzemelerin CBN takımlarla islenebilirliğini ve CBN takımların farklı isleme sartlarındaki performanslarını belirlemektir. Literatürde yapılmıs olan çalısmaların incelenmesi ile varılan değerlendirme ve sonuçların, bu alanda yapılacak bilimsel çalısmalara yardımcı olacağı ve özellikle imalat sektöründe çalısan uygulayıcılara yardımcı olacağı düsünülmektedir. Bu çalısma ayrıca, aynı malzemeler üzerinde karbür ve seramik takımların performanslarının değerlendirildiği iki farklı çalısmanın tamamlayıcısıdır.

Machinability of nickel-based superalloys and titanium alloys, part III: Evaluation of cubic boron nitride (CBN) cutting tools’performances

In this study, the performance of cubic boron nitride (CBN) cutting tools were assessed in the machining of nickelbased superalloys and titanium alloys with different operations through examination of the studies in the last decade. The aim of the study is to evaluate the machinability of these materials with CBN tools and to determine of these tools’ performances in different machining conditions. Evaluations and conclusions reached in this area will contribute to the scientific study and at the same time, is expected to be helpful for practitioners working in the manufacturing sector. This study also complements two different works relevant to evaluating the performances of carbide and ceramic cutting tools in the machining same superalloys.

PDF

___

1. http://www.jobshop.com/techinfo/papers/machiningtitanium.shtml, 2010,“Machining Titanium and Its Alloys”.
2. http://findarticles.com/p/articles/mi_m3101/is_2_75/ai_88760486, 2010, “Turning difficult-tomachine alloys: The special properties of superalloys and titanium alloys call for special machining considerations-Emphasis: Cutting Tools”.
3. Ezugwu, E.O., Bonney, J., Yamane, Y., 2003, “An overview of the machinability of aeroengine alloys”, Journal of Materials Processing Technology, 134; 233-253.
4. Choudhury, I.A., El-Baradie, M.A., 1998, “Machinability of nickel-based super alloys: a general review”, Journal of Materials Processing Technology, 77; 278–284.
5. Ezugwu, E.O., Wang, Z.M., Machado, A.R., 1999, “The machinability of nickel-based alloys: a review”, Journal of Materials Processing, Technology, 86; 1-16.
6. Pawade, R.S., Joshi, S. S., Brahmankar, P.K., Rahman, M., 2007 “An investigation of cutting forces and surface damage in high-speed turning of Inconel 718”, Journal of Materials Processing Technology, 192–193; 139–146.
7. Arunachalam, R.M., Manan, M.A., Spowage, A.C., 2004, “Residual stress and surface roughness when facing age hardened Inconel 718 with CBN and ceramic cutting tools”, Int. J. Mach. Tools Manuf., 44; 879–887.
8. Jemielniak, K, 2006, “Finish turning of Inconel 718”, CIRP- 2nd International Conference High Performance Cutting (HPC), Vancouver, Canada, June 12-13, paper 15.
9. Jemielniak, K., 2009, “Rough turning of Inconel 718”, Advances in Manufacturing, Science and Technology, 33 (3); 5-15.
10. Costes, J.P., Guillet, Y., Poulachon, G., Dessoly, M., 2007, “Tool-life and wear mechanisms of CBN tools in machining of Inconel 718”, International Journal of Machine Tools & Manufacture, 47; 1081- 1087.
11. Darwish, S.M., 2000, “The impact of the tool material and the cutting parameters on surface roughness of supermet 718 nickel superalloy”, Journal of Materials Processing Technology, 97;10-18.
12. Zoya, Z.A., Krishnamurthy, R., 2000, “The performance of CBN tools in the machining of titanium alloys”, Journal of Materials Processing Technology, 100; 80-86.
13. Rahman, M., Wang, Z.G., Wong, Y.S., 2006, “A review on high-speed machining of titanium alloys”, JSME International Journal Series C, 49 (1); 11-19.
14. Motorcu, A.R., 2009, “Nikel esaslı süperalasımların ve titanyum alasımlarının islenebilirliği, 1.Bölüm: Sinterlenmis karbür takımların performanslarının değerlendirilmesi”, Erciyes Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 25(1-2); 302-330.
15. Alauddin, M.A., El-Baradie, M.A., Hashmi, M.S.J., 1996, “End milling machinability of Inconel 718”, Journal of Engineering Manufacture, 210; 11-23.
16. Chen, Y.C., Liao, Y.S., 2003, “Study on wear mechanisms in drilling of Inconel 718 superalloy”, Journal of Materials Processing Technology, 140; 269–273.
17. Ezugwu, E.O., Wang, Z.M., 2000, “Wear of coated carbide tools when machining nickel (Inconel 718) and titanium base (Ti–6Al–4V) alloys”, Tribol. Trans., 43; 263–268.
18. Chen, Y.C., Liao, Y.S., 2003, “Study on wear mechanisms in drilling of Inconel 718 superalloy”, Journal of Materials Processing Technology, 140; 269–273.
19. Barry, J., Byrne, G., Lennon, D., 2001, “Observations on chip formation and acoustic emission in machining Ti-6Al-4V”, International Journal of Machine Tools & Manufacture, 41; 1055–1070.
20. Molinari, A., Musquar, C., Sutter, G., 2002, “Adiabatic shear banding in high speed machining of Ti- 6Al-4V: experiments and modeling”, International Journal of Plasticity, 18; 443-445.
21. Ezugwu, E.O., Da Silva, R.B., Bonney, J., Machado, A´. R., 2005, “Evaluation of the performance of CBN tools when turning Ti-6Al–4V alloy with high pressure coolant supplies”, International Journal of Machine Tools & Manufacture, 45; 1009–1014.
22. Corduan, N., Hirnbert, T., Poulachon, G., Dessob, M., Lambehn, M., Mgneau, J., Payod, B., 2007, “Wear mechanisms of new tool materials for TiBAI4V high performance machining” Journal of Materials Processing Technology, 192-193; 281-286.
23. Wang, Z.G., Rahman, M., Wong, Y.S., 2005, “Tool wear characteristics of binderless CBN tools used in high-speed milling of titanium alloys”, Wear, 258; 752–758.
24. Wang, Z.G., Wong, Y.S., Rahman, M., 2005, “High-speed milling of titanium alloys using binderless CBN Tools”, International Journal of Machine Tools & Manufacture, 45; 105–114.
25. Zoya, Z.A., Krishnamurthy, R., 2000, “The performance of CBN tools in the machining of titanium alloys”, Journal of Materials Processing Technology, 100; 80-86.
26. Nahbani, F., 2001, “Machining of aerospace titanium alloys”, Robotics and Computer Integrated Manufacturing, 17; 99-106.