Önder Tor, Samet Demirel, Lingling Hu, Jilei Zhang

Yönlendirilmiş Yonga Levhalarda Vidalama Torklarının Vida Çekme Direnci üzerine Etkisi

Bu çalışmada vidalama torklarının vida çekme direnci üzerindeki etkileri araştırılmıştır. Bu amaçla, dikey yönde vida çekme direnci testinde kullanılacak test numuneleri kılavuz deliğinin çapına (1.6, 2, 2.4 mm), vida çekme yönüne (kenar, son, ve yüzey) ve torklama seviyelerine göre hazırlanmıştır. Deney sonuçlarına göre, yüzey yönünde dikey çekme direnci diğer iki yöne göre daha yüksek dirence sahiptir. Vidalama tork seviyleri kıyaslandığında ise, vidanın boşta döndüğü torklama seviyelerinde, çekme direnci diğer seviyelere nazaran daha düşük seviyede olduğu bulunmuştur. Bu yüzden, vidalama yaparken özellikle kılavuz delik çalpları, vida çekme yönüne ve vidalama torkları seviyelerine göre dikkatli bir şekilde seçilmelidir.

Anahtar Kelimeler:

Çekme direnci, Vidalama torkları, Kılavuz delik çapı, OSB

Effects of Driving Torques on Direct Screw Withdrawal Resistance in OSB

This study was performed to evaluate effects of driving torques on direct screw withdrawal resistance (DSWR) in wood-based composites. Pilot hole diameters (1.6, 2, 2.4 mm), embedded screw orientations (edge-, end- and face-) and torque levels, that were obtained from the typical driving torque curve among two main driving torques, were selected to test on screw withdrawal resistance. The results of the study showed that the pilot hole diameters were needed to be chosen carefully related to the grain orientation. The screw withdrawal resistance in face-grain orientation had the highest DSWR than the ones in edge- and end- grain orientations. Based on the torque levels selected that the DSWR was lower at the torque level closer to the stripping torque levels in OSB.

Keywords:

Withdrawal resistance Driving torque, Pilot hole diameter, Grain orientation, OSB,

PDF

___

ASTM 2010a D-1761-06. Standard test method for mechanical fasteners in wood, American Society for Testing and Materials, West Conshohocken, PA.
ASTM 2010b D 1037-06. Standard test methods for evaluating properties of wood-base fiber and particle panel materials, American Society for Testing and materials, West Conshohocken, PA.
ASTM 2010c D 4442-92. Standard test methods for direct moisture content measurement of wood and wood-base materials. American Society for Testing and materials, West Conshohocken, PA.
Carroll, M.N., 1970. Relationship between driving torque and screw-holding strength in particleboard and plywood. Forest Prod J 20(3): 24-29.
Carter, D.R., Shimaoka, E.E., Harris, W.H., et al., 1984. Changes in long-bone structural properties during the first 8 weeks of plate implantation. Journal of Orthopaedic Research 2 (1), 80–89.
Didriksson, E.I.E., Nyren, J.O., Back, E.L., 1974. The splitting of wood-base building boards due to edge screwing. Forest Prod J 24(7):35-39.
Didrikson, E.I.E., Nyren J.O., Back, E.L., 1995. The splitting of wood-base building boards due to edge screwing. Journal of Forest Products 24(7): 35-39.
Eckelman, C.A, 1990. Fasteners and their use in particleboard and medium density fiberboard. National Particleboard Association. Purdue University.
Eckelman, C.A., 1973. Holding strength of screws in wood and wood-base materials. Res. Rept. No. 895. Agric. Expt. Sta. Purdue University, West Lafayette, Ind. pp:15.
Eckelman, C.A., 1975. Screw-holding performance in hardwoods and particleboard. Forest Products Jornal 25(6):30-35.
Eckelman, C.A., 1990. Fasteners and their use in particleboard and medium density fiberboard. National Particleboard Association. Purdue University.
Fujimoto, Y. and Mori, M., 1983. Performance of Wood Screw Joints for Particleboard. Science Bulletin of the Faculty of Agriculture, Kyushu
University, Japan 30(1): 45-47.
Jacobs, R., Rahn, B., Perren, S., 1981. Effect of plates on cortical bone perfusion. The Journal of Trauma 21 (2), 91–95.
Johnson, J.W. 1959. Screw-Holding Ability of Western Woods: Effects of Test Variables.
Lawson, K.J., Brems, J., 2001. Effect of insertion torque on bone screw pullout strength. Orthopedics 24(5):451–454.
National Particleboard Association, 1968. Screw holding of particleboard. Tech. Bull. No. 3, Washington, D.C.
Rajak. Z., Eckelman, C.A., 1993. Edge and face withdrawal strength of large screws in particleboard and medium density fiberboard. Forest Prod J 43(4):25-30.
Schmidt, H. 1986. Industrial particleboard: Application requirements and special manufacturing features. In: Proc. of the 20th WSU International
Particleboard/Composite Materials Symp. T.M. Maloney, Ed. Washing State Univ., Pullman, WA, pp. 343-354.
Stren, E.G., 1959. Wood screws for building construction and wood products assembly. Vir. Polytech. Inst., Wood Res. Lab., Bul.38.
Tor, O., Yu, X., Zhang, J., 2015. Characteristics of torques for driving screws into wood-based composites. Wood Fiber Sci 47(1).
Yu, X., Tor, O., Quin, F., Seale, D., Zhang, J., 2015. Screwdriving torques in particleboards. Wood Fiber Sci 47(2).
Zhang, J. and Eckelman, C. 2002. Holding strength of screws in plywood and oriented strandboard. Forest Prod J 52(6):55-62.