Shear Force Capacity of Various Doweled Frame Type Furniture Joints

Anahtar Kelimeler:

-

Shear Force Capacity of Various Doweled Frame Type Furniture Joints

Tests were carried out to determine the ultimate shear force capacity of numerous of doweled frame type furniture joints under controlled laboratory conditions. Sugar maple (Acer saccharum), soft maple (Acer negund), yellow poplar (Liriodendron tulipifera), sweetgum (Liquidambar styraciflua) and black walnut (Juglans nigra)were utilized in constructing the joint specimens, but all dowels were cut from yellow birch (Betula papyrifera) and sugar maple (Acer saccharum). Two types of specimens were used in the tests, including “in plane” and “out of plane” positions. Specimens were assembled with polyvinyl acetate adhesive. Specimens were tested under static load by applying shear forces. The results showed that the narrower dowel spacing provide greater shear force capacity for a specified rail width. It was deduced that there was a slight relationship between the shear strength of the wood used in the rail and the thickness of the rail and average ultimate shear force capacity of the joint. It was also demonstrated that the joints had essentially equal shear force capacity regardless of whether they were loaded in the flat wise or edgewise position. Furthermore, the average shear force capacity of dowel joints evaluated in this study could be estimated by developed predictive expressions

___

  • Eckelman, C. A., 1968: “Furniture frame analysis and design unpublished”, PhD. Thesis, Purdue University, West Lafayette, Indiana.
  • Eckelman, C. A., 1970: “The fatigue strength of two-pin moment resisting dowel joints”, Forest Products Journal, 20(5): 42-45.
  • Eckelman, C. A., 1971: “Bending strength and moment characteristics of two-pin moment resisting dowel joints”, Forest Products Journal, 21(3): 35-39.
  • Eckelman, C. A., 1979: “Out-of plane strength and stiffness of dowel joints”, Forest Products Journal, 29(8): 32-38.
  • Eckelman, C. A., 1991: “Textbook of product engineering and strength design of furniture”, Purdue University, West Lafayette, IN.
  • Engleson, T., 1973: “Summary of the investigations of several particleboards in the swedish”, Forest Products Lab, Stockholm.
  • Efe, H., 1998a: “Rational dowel design for furniture corner joints in case construction”, Journal of Polytechnic, Technical Education of Gazi University, 1(1-2): 65-74.
  • Efe, H., 1998b: “Mechanical behavior of different dowel types on frame construction of furniture end to end joints”, The Journal of the Industrial Arts, Education Faculty of Gazi University, 6(6): 113-131.
  • Efe, H. and Demirci S., 2000: “Effect of tensile strength according to the wood type glue type and wood section of dowel joints on frame construction of furniture”, Journal of Polytechnic, Technical Education of Gazi University, 3(4): 45- 51
  • Efe, H. and Demirci S., 2001: “Effect of the cutting direction to withdrawal strength of dowel on wood material”, Gazi University Journal of Science, 14(4): 1147-1154.
  • Efe, H., Demirci S. and Gürleyen L. 2002a: “The effect of wood moisture to tensile strength of side to side dowel joints for furniture”, The Journal of the Industrial Arts, Education Faculty of Gazi University, 10 (10): 13-23.
  • Efe, H., Demirci S. and Gürleyen L. 2002b: “The effect of moisture content of wooden material on dowel withdrawal strength of end to end joints”, The Journal of the Industrial Arts, Education Faculty of Gazi University, 10 (11): 137-146.
  • Erdil, Y.Z., 1994: “The general investigation of the fasteners used in the furniture industry”, Graduate Thesis, Technical Education of Gazi University, Ankara, Turkey.
  • Erdil, Y.Z., 1998: “Strength analysis and design of joints of furniture frames constructed of plywood and oriented strand-board”, M.Sc. Thesis, Purdue University, West Lafayette, Indiana.
  • Erdil, Y.Z. and Eckelman, C. A., 2001: “Withdrawal strength of dowels in plywood and oriented strand board”, Turkish J. of Agriculture and Forestry, 25: 319-327.
  • Hayashi, Y. and Eckelman, C. A., 1986: “Design of corner block with anchor bolt table joints”, Forest Product Journal, 36(2): 44-48.
  • Kasal, A., Erdil, Y.Z. and Eckelman, C. A., 2006: “Shear force and bending moment capacities of joints constructed with glued corner blocks”, Forest Product Journal, 56(9): 74-79.
  • Zhang, J.L., Quin, F., and Tackett, B., 2001: “Bending strength and stiffness of two-pin dowel joints constructed of wood and composites”, Forest Product Journal, 51(2): 29-35.
  • Zhang, J.L., Erdil, Y.Z., and Eckelman, C. A., 2002a: “Lateral holding strength of dowel joints constructed of plywood and oriented strand board”. Forest Product Journal, 52(10): 83-89.
  • Zhang, J.L., Erdil, Y.Z., and Eckelman, C. A., 2002b: “Torsional strength of dowel joints constructed of plywood and oriented strand board”, Forest Product Journal, 52(10): 89-94.
Kastamonu Üniversitesi Orman Fakültesi Dergisi-Cover
  • ISSN: 1303-2399
  • Yayın Aralığı: Yılda 3 Sayı
  • Başlangıç: 2001
  • Yayıncı: Kastamonu Üniversitesi