KLİNOPTİLOLİT TABANLI SERAMİK FİLTRELERİN ÜRETİMİNDE ALÜMİNYUM TANE BOYUTU ETKİLERİ

Bu makalede, klinoptilolit tabanlı seramik filtrelerin üretiminde tane boyutu etkileri araştırılmıştır. Burada klinoptilolit tozları ağırlıkça % 10 Al tozu ile karıştırılmış ve üç farklı klinoptilolit-metal toz karışımı örneği hazırlanmıştır: (i) iri taneli numune (iri boyutlu Al tozları kuru olarak bilyalı değirmende 5 dakika boyunca karıştırılmıştır), (ii) orta taneli numune (ince boyutlu Al-tozu kullanılmıştır), ve (iii) ince taneli numune (orta taneli numune planetary değirmende 1 saat öğütülmesi ile hazırlanmıştır). Karışımlar, 50 MPa basınç değerinde tek eksenli presle şekillendirilmiş ve daha sonra oksijen atmosferde 1200°C'de 1 saat süre ile sinterlenmiştir. Mikroyapı ve faz gelişimi SEM ve XRD analizleri ile araştırılmıştır. İri taneli numunede, korundum, silisyum (Si) ve düşük oranda kristobalit fazında kristalleşme elde edilmiştir. İnce ve orta taneli numunelerde ağırlıklı kristallenme kristobalittir. Planetary değirmende öğütülmüş numunede gözeneklilik düşüş gösterirken iri ve orta boyutlu tanelerin kullanıldığı numunelerde gözeneklilik ~%28 oranındadır, ancak gözenek boyut dağılımları farklılık göstermiş ve iri boyutlu tanelerin kullanıldığı numunede 150 mm'ye kadar büyük gözenekler gözlenmiştir. Orta boyutlu tanelerin kullanıldığı numunelerde nispeten küçük ve dar bir aralıkta gözenek dağılımı elde edilmiştir (4-65 mm).  Sonuçlar, orta boyutlu tanelerin kullanıldığı numunenin filtrasyon sırasında yüksek seçiciliğe sahip seramik filtrenin üretimine imkan sağladığını göstermektedir.

EFFECT OF PARTICLE SIZE OF ALUMINUM ON THE DEVELOPMENT OF CLINOPTILOLITE BASED POROUS CERAMIC FILTERS

This paper reports the effect of particle size of Al-metal powder addition on the development of clinoptilolite based porous ceramic filters. The clinoptilolite particles was mixed with 10 wt.% of Al-powder and the three different clinoptilolite-metal powder mixture samples were prepared namely: (i) coarse sample (used large size of Al-powder by mixing in dry ball mill for 5 min.), (ii) moderate sample (using fine size of Al-powder) and (iii) fine sample (planetary milling of the moderate sample in an aqueous medium for 1 hour). The mixtures were shaped by uniaxial pressing at 50 MPa and later sintered at the temperatures of 1200°C for 1 hour under air atmosphere. The microstructure and phase evolution were investigated by SEM and XRD, respectively. The coarse sample indicated corundum crystallization with silicon (Si) and with poor cristobalite crystallization. The cristobalite crystallization is prodominantly for the fine and moderate samples. Except the planetery milled sample (fine) the porosities of the samples were good enough (~28%) but the pore sizes were different; the coarse sample showed large pores up to 150 mm in size, the moderate sample produced relatively fine and narrow pore size distribution (4-65 mm). The results indicated that the moderate sample leads to production of ceramic filter with high selectivity during filtration.

___

  • [1]Wu, S., Gesing, A.J., Travitzky, N.A., Claussen, N., Fabrication and properties of Al-infiltrated RBAO-based composites, J. Eur. Ceram. Soc. 7, 277–281, (1991).
  • [2]Claussen N., T. S.,Wu Le, , Low-shrinkage reaction-bonded alumina, J. Eur. Ceram. Soc. 5 29–35, (1989).
  • [3]Ebadzadeh, T., Porous mullite-ZrO2 composites from reaction sintering of zircon aluminium, Ceram. Int. 31, 1091-1095, (2005).
  • [4]Esharghawi, A., Penot, C., Nardou, F., Contribution to porous mullite synthesis from clays by adding Al and Mg powders, J. Eur. Ceram. Soc 29, 31–38, (2009).
  • [5]Sahraoui, T., Belhouchet, H., Heraiz, M., Brihi, N., Guermat, A., The effects of mechanical activation on the sintering of mullite produced from kaolin and aluminum powder, Ceram. Int. 42, 12185–12193, (2016).
  • [6]Issaoui, M., Limousy, L., Lebeau, B., Bouaziz, J., Fourati, M., Design and characterization of flat membrane supports elaborated from kaolin and aluminum powders, C. R. Chimie 19, 496-504, (2016).
  • [7]Balmori-Ramirez, H., Rocha-Range1, E., Refugio-Garcia, E., C. Bradt, R., Dense Mullite from Attrition-Milled Kyanite and Aluminum Metal, J.Am. Ceram. Soc. 87 (1) 144-146, (2004).
  • [8]Sadika, C., El Amranib, I. E., Albizane, A., Effect of andalusite rich schist grain size and the addition of metallic aluminumpowder on the properties of silica–alumina refractory, J. Asian Ceram. Soc. 1, 351–355, (2013).
  • [9]Kingery, W.D., Bowen, H.K., Uhlmann, D.R., Introduction to Ceramics, Wiley, New York, (1976).
  • [10]Essl, F., Bruhn, J., Janssen, R., Claussen, N., Wet milling of Al-containing powder mixtures as precursor materials for reaction bonding of alumina (RBAO) and reaction sintering of alumina-aluminide alloys (3A), Mater. Chem. Phys. 61, 69-77 (1999).
  • [11]Andreola, F., Manfredini, T., Passaglia, E., Pellacani, G.C., Pozzi P., Romagnoli, M., Utilazition of an Italian Zeolitite in Ceramic Bodies, Mater. Eng. Vol. 5, 299-312, (1994).
  • [12]De Gennaro, R., Cappelletti, P., Cerri, G., de Gennaro, M., Dondi, M., Guarini, G., Langella A., Naimo, D., Influence of zeolites on the sintering and technological properties of porcelain stoneware tiles, J. Eur. Ceram. Soc. Vol. 23, 22372245, (2003).
  • [13] Şan, O., Abalı S., Hoşten, Ç., Fabrication of Microporous Ceramics from Ceramic Powders of QuartzNatural Zeolite Mixtures, Ceram. Int. vol. 29, 927931, (2003).
  • [14] Al-Harbi, O. A., Khan, M. M, Özgür, C., Improving The Performance of Silica-based Crossflow Membranes by Surface Crystallization for Treatment of Oily Wastewater, J. Aust. Ceram. Soc. Vol. 53, 883-894, (2017).
  • [15]Şan, O., Özgür, C., Investigation of a High Stable-Cristobalite Ceramic Powder from CaO–Al2O3–SiO2 System, J. Eur. Ceram. Soc 29, 2945–2949, (2009).
  • [16] Şan, O., Özgür, C., Preparation of a Stabilized-Cristobalite Ceramic from Diatomite, J. All. Comp. 484, 920–923, (2009).