___

• [1] Meslameni, W., Kamoun, T., & Hbaieb, M. (2019). Experimental modeling of EDM process using the experimental design method, Int J Applied Research and Technology, 2, 39-47.
• [2] Agarwal, N., Shrivastava, N., & Pradhan, M.K. (2019). Optimization of relative wear ratio during EDM of titanium alloy using advanced techniques, SN Applied Sciences, 2, 99. https://doi.org/10.1007/s42452-019-1877-2
• [3] Prathipati, R., Dora, S.P., & Chanamala, R. (2020). Wear behavior of wire electric discharge machined surface of 316L stainless steel, SN Applied Sciences, 2, 412. https://doi.org/10.1007/s42452-020-2244-z
• [4] Prathipati, R., Ch, R., & Dora, S.P. (2019). Corrosion behavior of surface induced by wire EDM on 316L stainless steel: an experimental investigation, SN Applied Sciences, 1, 952. https://doi.org/10.1007/s42452-019-0992-4
• [5] Dewan, P.R., Lepcha, L.P., Khaling, A.N., Prasad, N., & Rai, S. (2018). Experimental Analysis and Optimization of EDM Process Parameters, IOP Conf. Series: Materials Science and Engineering, 377, 012220. doi:10.1088/1757-899X/377/1/012220
• [6] Kolse, D.M., & Shrivastava, R.K. (2017). Effect of Electrode Materials and Optimization of Electric Discharge Machining of M2 Tool Steel Using Grey-Taguchi Analysis, International Journal of Scientific Research in Science and Technology, 3(8), 1020-1027.
• [7] El‑Bahloul, S.A. (2020). Optimization of wire electrical discharge machining using statistical methods coupled with artificial intelligence techniques and soft computing, SN Applied Sciences, 2, 49. https://doi.org/10.1007/s42452-019-1849-6
• [8] Mohanty, U.K., Rana, J., & Sharma, A. (2017). Multi-objective optimization of electro-discharge machining EDM parameter for sustainable machining, Materials Today: Proceedings, 4(8), 9147–9157. https://doi.org/10.1016/j.matpr.2017.07.271
• [9] Chandramouli, S., & Eswaraiah, K. (2018). Experimental investigation of EDM Process parameters in Machining of 17-4 PH Steel using Taguchi Method, Materials Today: Proceedings, 5(2), 5058–5067. https://doi.org/10.1016/j.matpr.2017.12.084
• [10] Satpathy, A., Tripathy, S., Senapati, N.P., & Brahma, M.K. (2017). Optimization of EDM process parameters for AlSiC- 20% SiC reinforced metal matrix composite with multi response using TOPSIS, Materials Today: Proceedings, 4(2), 3043–3052. https://doi.org/10.1016/j.matpr.2017.02.187
• [11] Parsana, S., Radadia, N., Sheth, M., Sheth, N., Savsani, V., Prasad, N.E., & Ramprabhu, T. (2018). Machining parameter optimization for EDM machining of Mg–RE–Zn–Zr alloy using multi-objective Passing Vehicle Search algorithm, Archives of Civil and Mechanical Engineering, 8(3), 799-817. https://doi.org/10.1016/j.acme.2017.12.007
• [12] Saffaran, A., Moghaddam, M.A., & Kolahan, F. (2020). Optimization of backpropagation neural network‑based models in EDM process using particle swarm optimization and simulated annealing algorithms, Journal of the Brazilian Society of Mechanical Sciences and Engineering, 42, 73. https://doi.org/10.1007/s40430-019-2149-1
• [13] Subrahmanyam, M., & Nancharaiah, T. (2020). Optimization of process parameters in wire-cut EDM of Inconel 625 using Taguchi’s approach, Materials Today: Proceedings, 23(3), 642-646. https://doi.org/10.1016/j.matpr.2019.05.449
• [14] Mohamed, M.F., Lenin, K. (2020). Optimization of Wire EDM process parameters using Taguchi technique, Materials Today: Proceedings, 21(1), 527-530. https://doi.org/10.1016/j.matpr.2019.06.662
• [15] Tlili, A., & Ghanem, F. (2018). A numerical investigation on the local mechanical behavior of a 316-L part during and after an EDM basic electrical discharge, Int J Adv Manuf Technol. https://doi.org/10.1007/s00170-018-2618-1
• [16] Singh, N.K., Agrawal, S., Johari, D., & Singh, Y. (2019). Predictive analysis of surface roughness in argon‑assisted EDM using semiempirical and ANN techniques, SN Applied Sciences, 1, 995. https://doi.org/10.1007/s42452-019-1032-0
• [17] Abu Qudeiri, J.E., Saleh, A., Ziout, A., Mourad, A.I., & Elkaseer, A. (2019). Advanced Electric Discharge Machining of Stainless Steels: Assessment of the State of the Art, Gaps and Future Prospect, Materials, 12, 907. doi:10.3390/ma12060907
• [18] Sharma, S., Vates, U.K., & Bansal, A. (2021). Parametric optimization in wire EDM of D2 tool steel using Taguchi method, Materials Today: Proceedings, 45(2), 757-763. https://doi.org/10.1016/j.matpr.2020.02.802.
• [19] Satishkumar, P., Murthi, C.S., & Meenakshi, R. (2021). Optimization of machining parameters in wire EDM of OFHC copper using Taguchi analysis, Materials Today: Proceedings, 37(2), 922-928. https://doi.org/10.1016/j.matpr.2020.06.120
• [20] Girisha, L., Sridhar, S., Tadepalli, L.D., Swetha, M., Subbiah, R., & Marichamy, S. (2021). Performance analysis and taguchi approach on wire cut EDM using microwave sintered chromium composite, Materials Today: Proceedings, 45(2), 2105-2108. https://doi.org/10.1016/j.matpr.2020.09.700
• [21] Ganapati, S.T., Pachapuri, M.S.A., & Adake, C.V. (2019). Influence of process parameters of electrical discharge machining on MRR, TWR and surface roughness: A review, AIP Conference Proceedings, 2148, 030045. https://doi.org/10.1063/1.5123967
• [22] Meslameni, W., & Ben Salem, C. (2021). Modeling of the springback in folding using the experimental design method. Journal of applied research on industrial engineering, 8(3), 290-308. Doi: 10.22105/JARIE.2021.280059.1284