An Investigation of Punch Radius and Clearance Effects on the Sheet Metal Blanking Process

In this study, the effects of punch edge radius and blanking clearance on product quality and blanking process in blanking of AISI 304 stainless steel sheet were investigated by using the fi-nite element analysis method. The blanking analyzes were performed at four different punch tip radii (0.01, 0.25, 0.5, 1 mm) and three different blanking clearance (1 %, 5%, 10%). As a result of the analysis, rollover, burr length increased, smooth sheared / fractured surface ratio and blanking force decreased with the increase in blanking clearance. Depending on the increase in the amount of punch tip radius, the blanking force, and burr length also increased, and the smooth sheared / fractured surface ratio decreased compared to the blanking process with flat punches.

Keywords:

Sheet metal blanking, Clearance, Punch radius, Blanking force, Burr sheet metal forming,

PDF

___

[1] Zhang Z, Xia S, Bai Q, Liu T, Li H, Zhou B. Effects of 3-D grain boundary geometrical angles and the net normal stress on inter-granular stress corrosion cracking initiation in a 316 stainless steel. Mater Sci Eng A. 2019;765(July):138277.
[2] Monrrabal G, Bautista A, Guzman S, Gutierrez C, Velasco F. In-fluence of the cold working induced martensite on the electrochem-ical behavior of AISI 304 stainless steel surfaces. Integr Med Res. 2018;8(1):1335–46.
[3] Guo R, Shen Y, Huang G, Zhang W, Guan W. Microstructures and mechanical properties of thin 304 stainless steel sheets by fric-tion stir welding. J Adhes Sci Technol. 2018;4243:1–11.
[4] Alexander D, Christian M, Ruben K, Hetfleisch H, Groche P. Workpiece image-based tool wear classification in blanking pro-cesses using deep convolutional neural networks. Prod Eng. 2022;16(4):481–92.
[5] Sujeesh VA, Prakash A, Natarajan R. Materials Today : Proceed-ings Implementation of precision manufacturing control for pro-cessing of sheet metal. Mater Today Proc. 2022;62:1143–5.
[6] Cavusoglu O, Gurun H, Kafkas F, Efendioglu S, Mert F. The ef-fects of punch angle in noise and force formation for sheet metal blanking process. Journal of Process Mechanical Engineering. 2022;236(4):1477–84.
[7] Li Y, Zhao Y, Hao Y. Numerical Simulation of Fine Blanking Die Wear and Die Performance Analysis. Journal of Chemistry, 2022; 9893356:1-7.
[8] Han S, Chang Y, Wang CY, Dong H. A comprehensive investiga-tion on the damage induced by the shearing process in DP780 steel. J Mater Process Tech. 2022;299(2):117377.
[9] Basak S, Kim C, Jeong W, Il Y, Lee M. International Journal of Mechanical Sciences Numerical prediction of sheared edge profiles in sheet metal trimming using ductile fracture modeling. Int J Mech Sci. 2022;219:107109. [10] Basak S, Kim C, Il Y, Hong J, Jin K, Gyu M. Analyses of shear-ing mechanism during shear-cutting of 980 MPa dual-phase steel sheets using ductile fracture modeling and simulation. Int J Mater Form . 2022;15(4):1-21.
[11] Senn, S, Liewald M. Investigation of a new sheet metal shear cutting tool design to increase the part quality by superposed com-pression stress. IOP Conf Ser Mater Sci Eng. 2019;651(012088).
[12] Gomah, M, Demiral M. An experimental and numerical investiga-tion of an improved shearing process with different punch charac-teristics. Strojniški vestnik - Journal of Mechanical Engineering. 2020;6:375-384.
[13] Abe Y, Yonekawa R, Sedoguchi K, Mori K, Zanin A, Wernke R. Shearing of ultra-high strength steel sheets with step punch. Proce-dia Manuf . 2018;15:597–604.
[14] J. A. Soares, M. L. Gipiela SFL& PVPM. Study of the punch – die clearance influence on the sheared edge quality of thick sheets. Int J Adv Manuf Technol. 2013;65:451–7.
[15] Fazily P, Yu J, Lee C. Characterization of Sheared Edges in Warm Blanking of Magnesium Alloy AZ31B. 2019;12(7)-1023.
[16] Roizard MSX, Colas MAG, Barbe SGJP. Finite element simula-tion and experimental investigation of the effect of clearance on the forming quality in the fine blanking process. Microsyst Technol. 2021;27(3):871–81.
[17] Gustafsson E, Oldenburg M, Jansson A. Experimental study on the effects of clearance and clamping in steel sheet metal shearing. Journal of Materials Processing Technology. 2016;229:172–80.
[18] So H, Faßmann D, Hoffmann H, Golle R, Schaper M. Journal of Materials Processing Technology. An investigation of the blanking process of the quenchable boron alloyed steel 22MnB5 before and after hot stamping process. J Mater Process Tech. 2012;212(2):437–49.
[19] Canales C, Bussetta P. On the numerical simulation of sheet metal blanking process. International Journal of Material Forming. 2017;10:55–71.
[20] Korkmaz HG, Toros S, Halkaci M, Halkaci HS. Investigation of hydro-piercing method for stainless steels by finite element method element hydropiercing process modeling of. 2018;3.
[21] Korkmaz, Habip Gökay, Toros, Serkan, Halkacı HS. Investiga-tion of hydro-piercing method for stainless steels by finite element method. Omer Halisdemir Univ J Eng Sci. 2018;7(2):954–65.
[22] Cavusoglu O, Gurun H. Investigation and fuzzy logic prediction of the effects of clearance on the banking process of cuzn30 sheet metal. Kov Mater - Met Mater. 2016;54(2):125–31.
[23] Mahalle G, Salunke O, Kotkunde N, Kumar A. Neural network modeling for anisotropic mechanical properties and work hardening behavior of Inconel 718 alloy at elevated. Integr Med Res. 2019;8(2):2130–40.