Failure Analysis of Hybrid Glass Reinforced Composites in Polymeric Industries

This research deals with the failure analysis of hybrid glass reinforced composites in polymeric industries. In this research, fourteen specimens with different compositions were developed. The produced test specimens had a dimension of 210mm length, 150mm width and 50mm thickness which were in accordanc--e with American Society for Testing and Materials (ASTM). The fourteen test specimens produced were subjected to impact test. The critical stress, shear stress and stress distribution for mode I and mode II were investigated and results were obtained. The results obtained shows that specimen A had an optimum critical and shear stress of 9.32 MPa and 25.1 MPa for mode I while specimen C had an optimum critical and shear stress of 2.49 MPa and 7.03 MPa for mode II respectively. It was also observed that specimen I which contained 12 plies of soft mat reinforcement required the least stress magnitude to grow the crack, while specimen C which contained 2 plies of woven roving and one ply of hat mat experienced the highest critical stress. Hence, adequate percentage composition of E-glass and polyester reduces failure in hybrid glass composites in polymeric industries.

Keywords:

Failure Analysis, Fracture Modes Hybrid Glass Reinforced Composite,

PDF

___

Dhakal, H. N., Zhang, Z. Y., Richardson, M. O. W., & Errajhi, O. A. Z. (2006). The Low Velocity Impact Response of Non-woven Hemp Fibre Reinforced Unsaturated Polyester Composites. Advanced Polymer and Composites (APC) Research Group, Department of Mechanical and Design Engineering, University of Portsmouth. Retrieved from www.elsevier.com.
Idicula, M., Joseph, K., & Thomas, S. (2009). Mechanical Performance of Short Banana/Sisal Hybrid Fibre Polyester Composite. Journal of Reinforced Plastics and Composites, 29(1), 12– 29.
Janssen, M., Zuidema, J., & Wanhill, R. J. H. (2004). Fracture Mechanics. (2nd Edition). New York: Spon Press.
Krueger, R. (2006). Fracture Mechanics for Composites: State-Of-The-Art and Its Challenges. NAFEMS Nordic Seminar: Prediction and Modelling of Failure Using FEA, National Institute of Aerospace, USA. Retrieved from ntrs.nasa.gov
Mueller, D. H., & Krobjilowski, A. (2004). Improving the Impact Strength of Natural Fibre Reinforced Composites By Specifically Designed Materials and Process Parameter. International Nonwovens Journal, 13(4), 31-38.
Olodu, D. D., & Osarenmwinda, J. O. (2018). Emperical Modelling of Injection Moulded High Density Polyethylene-Grass Composite. American Journal of Engineering Research (AJER), 7(12), 245-250.
Orbulov, I. N., & Ginsztler, J. (2014). Compressive Behaviour of Metal Matrix Syntactic Foams. Acta Polytechnica Hungarica, 9(2), 43-56.
Osarenmwinda, J. O., & Nwachukwu, J. C. (2010). Development of Composite Material from Agricultural Waste. International Journal of Engineering Research in Africa, 3, 42-48.
Parhizgar, S., Zachary, L. W., & Sun, C. T. (1982). Application of the Principle of Linear Fracture Mechanics to the Composite Materials. International Journal of Fracture Mechanics, 20, 3-15.
Radif, Z. S., & Ali, A. (2001). Fracture Toughness of Kenaf Mat Reinforced Polyester Composite. Pertanika Journal of Science and Technology, 99(1), 177-187.
Romanova, V. A., Balokhonov, R. R., & Schmauder, S. (2009). The Influence of the Reinforcing Particle Shape and Interface Strength on the Fracture Behavior of a Metal Matrix Composite. Acta Materialia, 57(1), 97-107.
Williams, J. G, (1978). Linear Fracture Mechanics. Advances in Polymer Science, 27, 69-82.

Gazi University Journal of Science Part A: Engineering and Innovation-Cover

Yayın Aralığı: Yılda 4 Sayı
Başlangıç: 2013
Yayıncı: Gazi Üniversitesi, Fen Bilimleri Enstitüsü

Arşiv