Fatih Süleyman TAŞKINCAN, Ahmet KARAARSLAN, Zafer ORTATEPE

The Implementation of Internal Mode Control Method to SEPIC Converter for Battery Charging Systems

In this paper, internal model control (IMC) method, which is a model-based approach that offers more robust and better reference tracking capability than conventional controllers for the unstable process, is applied to the SEPIC converter used in battery charging system for military applications. When a system is not based on a plant model, it is possible to encounter some problems such as dead time and non-linearity in controlling of the system. The purpose of the SEPIC topology is to eliminate the disadvantage of other topologies such as Buck-Boost and Cúk converters that are used for similar applications in reversing the output voltage. In addition, a great amount of voltage and current stress on a component causes the power board to overheat in such converters and requires additional cooling equipment. These problems are not encountered in SEPIC topology. Also, this topology provides high efficiency, step-up/step-down voltage conversion, and excellent transient state response over a wide range. The performance of IMC method applied on SEPIC converter is detailed analyzed in terms of simulation studies that are obtained by using MATLAB/Simulink and experimental studies.

Keywords:

Internal model control (IMC), battery charging system, SEPIC converter,

PDF

___

[1] Massey R.P., Snyder E.C., High voltage single-ended DC/DC converter, IEEE Power Electronics Specialists Conference, (1977) 156-159.
[2] Luo F.L., Ye H., Advanced DC/DC Converters, CRC Press, (2004) 55-60.
[3] Roberts S., DC/DC Book of Knowledge Practical tips for the User (Third Ed.), (2016) 1-59.
[4] Font J., Vicuña L. G., Guinjoan F., Majó J., Martinez L., A contribution to the analysis of the SEPIC converter, Proceedings of the IASTED Symposium Identification Modelling and Simulation, (1987) 355-358.
[5] Vicuña L. G., Guinjoan F., Majó J., Martinez L., Discontinuous conduction mode in the SEPIC converter, MELECON '89: Mediterranean Electrotechnical Conference Proceedings. Integrating Research Industry and Education in Energy and Communication Engineering, (1989) 38-42.
[6] Eng V., Pinsopon U., Bunlaksananusorn C., Modeling of a SEPIC converter operating in continuous conduction mode, 6th International Conference on Electrical Engineering/Electronics, Computer, Telecommunications and Information Technology, Pattaya, Chonburi, (2009) 136-139.
[7] Jose R., Anisha S., Vani V., Kshemada D., DC-DC SEPIC converter topologies, International Journal of Research in Engineering and Technology, 04 No. 05 (2015) 20-23.
[8] Bequette B. W., Nonlinear control of chemical processes: a review, Industrial &Engineering Chemistry Research, 30 (1991) 1391-1413.
[9] Muhammad D., Ahmad Z., Aziz N., Implementation of internal model control (IMC) in continuous distillation column, Proc. of the 5th International Symposium on Design, Operation and Control of Chemical Processes, (2010) 812-821.
[10] Garcia C. E., Morari M., Internal model control. A unifying review and some new results, Industrial & Engineering Chemistry Process Design and Development, 21 (1982) 308-323.
[11] Morari M., Zafiriou E., Robust Process Control, Prentice Hall, (1989).
[12] Garcia C. E., Morari M., Internal model control 3. Multivariable Control Law Computation and Tuning Guidelines, Industrial & Engineering Chemistry Process Design and Development, 24 (1985) 484-494.
[13] Tarakanath K., Patwardhan S., Agarwal V., Internal model control of dc-dc boost converter exhibiting non-minimum phase behavior, IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES), Bombay, India, (2014) 1-7.
[14] Sun X., Shi Z., Chen L., Yang Z., Internal Model Control for a Bearingless Permanent Magnet Synchronous Motor Based on Inverse System Method, IEEE Transactions on Energy Conversion, 31 No. 4 (2016) 1539-1548.
[15] Liu G., Chen L., Zhao W., Jiang Y., Qu L., Internal Model Control of Permanent Magnet Synchronous Motor Using Support Vector Machine Generalized Inverse, IEEE Transactions Industrial Informatics, 9 No. 2 (2013) 890-898.
[16] Rashid M. H., Power Electronics Handbook Devices, Circuit, and Applications (3rd Ed.), Elsevier, (2011).
[17] Middlebrook R., Cuk S., A general unified approach to modelling switching converter power stages, IEEE Power Electronic Specialists Conference, (1976) 18-34.
[18] Polsky T., Horen Y., Bronshtein S., Baimel D., Transient and Steady-State Analysis of a SEPIC Converter by an Average State Space Modelling, IEEE 18th International Power Electronics and Motion Control Conference (PEMC), Budapest, (2018), 211-215.