DP600 Malzemenin Şekillendirilmesinde Değişken Baskı Plakası Kuvveti Etkisinin Sonlu Elemanlar Yöntemiyle Araştırılması
Otomotiv üreticileri hem ağırlık/dayanım oranının düşürülmesinde hem de çarpışma anında daha mukavemetliaraçları üretmek için ultra yüksek mukavemetli malzemelerin kullanım oranını gittikçe artırmaktadır. Buçalışmada, ultra yüksek mukavemetli DP600 malzemesi için sonlu elemanlar yöntemi kullanılarakşekillendirebilirlik analizi yapılmıştır. Kalıp tasarımı yapılarak belirli bir geometride ve başlangıçta 1 mmkalınlığındaki sac malzeme için sanal ortamda hem sabit hem de değişken baskı plakası kuvvetlerinde derinçekme işlemi uygulanarak malzemenin oda şartlarında her iki farklı yöntem için sınır çekme oranı belirlenmiştir.Derin çekme analizleri sonucunda değişken baskı plakası kuvveti kullanılarak sınır çekme oranı 2,07’den2,12’ye yükseldiği tespit edilmiştir.
Investigation of The Effect of Variable Blank Holder Force on The Forming of DP600 Material via Finite Element Method
Automobile manufacturers increase the usage of ultra-high strength materials for both lowering the weight/strength ratio and manufacturing stronger vehicles. In this study, the finite element forming analysis has been applied to the ultra-high strength DP600 material. The limit drawing ratio has been determined in finite elements by designing a die for a sheet material initially of 1 mm thickness and at certain geometry in both constant and variable blank holder forces. As a result of deep drawing analyses, the limit drawing ratio has been determined to be increased from 2.07 to 2.12 by employing variable blank holder force.
___
- C. Özek ve E. Ünal, “The effect of die / blank holder angles on limit drawing ratio and wall
thickness in deep drawing of square cups,” Journal of the Faculty of Engineering and
Architecture of Gazi University, vol. 27, no. 3, pp. 615–622, 2012.
- S. Keeler, M. Kimchi ve P. J. Mooney, “Advanced high-strength steels apllication guidelines
version 6.0” no. September, p. 314, 2017.
- J. Venezuela, J. Blanch, A. Zulkiply, Q. Liu, Q. Zhou, M. Zhang ve A. Atrens, “Further study
of the hydrogen embrittlement of martensitic advanced high-strength steel in simulated auto
service conditions,” Corrosion Science, vol. 135, no. February, pp. 120–135, 2018.
- Q. Liu, Q. Zhou, J. Venezuela, M. Zhang ve A. Atrens, “Hydrogen influence on some
advanced high-strength steels,” Corrosion Science, vol. 125, no. March, pp. 114–138, 2017.
- C. M. Tamarelli, “AHSS 101: the evolving use of advanced high-strength steel for automotive
applications,” Steel Market Development Institute, p. 42, 2011.
- J. Venezuela, Q. Zhou, Q. Liu, M. Zhang ve A. Atrens, “Influence of hydrogen on the
mechanical and fracture properties of some martensitic advanced high strength steels in
simulated service conditions,” Corrosion Science, vol. 111, pp. 602–624, 2016.
- A. O. Özdemir, H. Şirin ve Ç. Karataş, “Otomotiv endüstrisinde kullanılan çelik saclardaki
alaşım elementlerinin şekillendirmeye etkisinin araştırılması,” Gazi Üniversitesi Fen Bilimleri
Dergisi Part:C, Part C, vol. 5, no. 4, pp. 109–119, 2017.
- E. Kayhan, “The development of a method to improve the limit drawing ratio of blanks using
preferential heating,” Yüksek Lisans, İmalat Mühendisliği, Atılım Üniversitesi, Ankara,
Türkiye, 2015.
1304
- T. Yagami, K. Manabe ve Y. Yamauchi, “Effect of alternating blank holder motion of drawing
and wrinkle elimination on deep-drawability,” Journal of Materials Processing Technology,
vol. 187–188, pp. 187–191, 2007.
- H. I. Demirci, C. Esner ve M. Yasar, “Effect of the blank holder force on drawing of aluminum
alloy square cup: Theoretical and experimental investigation,” Journal of Materials Processing
Technology, vol. 206, no. 1–3, pp. 152–160, 2008.
- S. Yoshihara, K. I. Manabe ve H. Nishimura, “Effect of blank holder force control in deepdrawing process of magnesium alloy sheet,” Journal of Materials Processing Technology, vol.
170, no. 3, pp. 579–585, 2005.
- C. Özek ve V. Taşdemir, “Alüminyum alaşımının derin çekilmesine sıcaklığın etkisinin
deneysel ve sayısal olarak araştırılması” Politeknik Dergisi, c.21, s.1, ss. 193-199, 2018.
- C. Özek ve V. Taşdemir, “AA 5754-O alaşımının ılık derin çekilmesi üzerine kalıp yüzey açısı
ve baskı plakası kuvvetinin etkisinin deneysel araştırılması” Journal of the Faculty of
Engineering and Architecture of Gazi University, c.32, s.1, ss. 193-201, 2017.
- S. Candra, I. M. L. Batan, W. Berata ve A. S. Pramono, “Analytical study and FEM simulation
of the maximum varying blank holder force to prevent cracking on cylindrical cup deep
drawing,” Procedia CIRP, vol. 26, pp. 548–553, 2015.
- I. Aminzahed, M. Mosavi Mashadi ve M. R. V. Sereshk, “Investigation of holder pressure and
size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator,”
Materials Science and Engineering C, vol. 71, pp. 685–689, 2017.
- Y. Feng, Z. Zhang, G. Tian, Z. Lv, S. Tian ve H. Jia, “Data-driven accurate design of variable
blank holder force in sheet forming under interval uncertainty using sequential approximate
multi-objective optimization,” Future Generation Computer Systems, vol. 86, pp. 1242-1250,
2018.
- P. Kováč ve V. Tittel, “Blank holder force optimization of hemispherical product using
numerical simulation In,” Materials science and technology, No. 5, pp. 5–10, 2010.