Power Quality Disturbances And Custom Power Devices

Lineer olmayan yüklerin endüstride artan kullanımıyla harmonik, kırpışma ve dengesizlikler önemli bir sorun olmuştur. Dağıtım/iletim hatlarında olan yıldırımlar ve çeşitli şebeke hataları geçişlere, gerilim düşümlerine/yükselimlerine ve kesintilere neden olabilir. Güç elektroniği cihazlarının fiyatlarının azalması, çevirici ve enerji depolama cihazlarının verimliliklerinin artmasıyla, yeni teknolojik çözüm olan Özel Güç Cihazlarının güç kalitesi problemlerini yok etmek için kullanılabilirliğini arttırmıştır. Statik Transfer Anahtarı (STA) genellikle kesintileri ve gerilim düşümü/yükselimini düzeltmek için kullanılır. Aktif Güç Filtresi (AGF) genellikle akım harmoniklerini, kırpışmaları ve dengesizlikleri elemek için kullanılır. Dinamik Gerilim İyileştirici (DGİ) genellikle gerilim düşümü/yükselimini kompanse etmek için kullanılır, Birleştirilmiş Güç Kalitesi Düzenleyici (BGKD)ise DGİ ve AGF’nin özelliklerini gerçekleştirir. Bu çalışmada güç kalitesinin temelleri, Özel Güç cihazlarının konfigürasyonları ve temel çalışma prensipleri sunulmuştur

Güç Kalitesi Ve Özel Güç Cihazları

Harmonics, flicker and imbalance have become serious concerns with the increasing use of nonlinear loads in industries. Lightning strikes on transmission/distribution lines and several network faults can also cause transients, voltage sag/swell and interruption. Decrease in the cost of power electronic devices and improvement in the efficiency of both power converters and energy storage components have increased the applicability of new technological solutions such as Custom Power devices to mitigate the power quality disturbances. Static Transfer Switch (STS) is generally used to mitigate voltage sag/swell and interruption, Active Power Filter (APF) is generally used to eliminate current harmonics, flicker and imbalance, Dynamic Voltage Restore (DVR) is generally used to compensate voltage sag/swell and Unified Power Quality Conditioner (UPQC) performs the tasks of DVR and APF. In this paper, the basics of power quality, configuration and operation principles of custom power devices are presented.

___

  • 1. Dong, Z.Y. and Saha, T. (2004). Power Quality & Equipment Protection. ELEC4301, pp. 1-34.
  • 2. Shiva S. Rajat K.S. (1998). Review of Power Quality Applications of Energy Storage Systems, Contractor Report. Sentech Inc.. Sandia National Laboratories.
  • 3. Emanuel A. E. Mcneill J. A. (1997). Electric power quality, Annual review of energy and the environment, 22:263-303.
  • 4. Liu S. Singer C.H. Dougal R.A. (2006). Power anomaly effects and costs in lowvoltage mobile power systems aerospace and electronic systems, IEEE Transactions on Aerospace and Electronic Systems, 42:612-624.
  • 5. Seng L.Y. (2002). Probabilistic assessments of voltage-sag occurrence and the evaluation of the dynamic voltage restorer capability. PhD thessis. University of Manchester Institute of Science and Tech.
  • 6. Kurt S. François D. (2010). The Importance Of Good Power Quality, ABB Power Quality Products, pp. 1-20.
  • 7. Taylor G.A. (1995). Power Quality Hardware Solutions for Distribution Systems: Custom Power. IEE Reliability, Security and Power Quality of Distribution Systems, 11/1-11/9..
  • 8. Brenna M. Tironi R.F. (2009). A new proposal for power quality and custom power improvement OPEN UPQC, IEEE Transactions on Power Delivery, 24: 2107-2116.
  • 9. Lara O.A. and Acha E. (2002)ç. Modeling and Analysis of Custom Power Systems by PSCAD/EMTDC, IEEE Transactions On Power Delivery, 17(1): 266-272.
  • 10. Stones J. and Collinson A. (2001). Special Feature: Introduction Power Quality. IEE Power Engineering Journal, 58-64.