Serkan ÖZEL, Kübra ASLAN

Investigation of The Effect of Cr2O3 Particles on Al-Si Matrix Composites Produced by Powder Metallurgy

Anahtar Kelimeler:

Powder Metallurgy, Composite materials, Al, Cr2O3, Microstructure.

Investigation of The Effect of Cr2O3 Particles on Al-Si Matrix Composites Produced by Powder Metallurgy

Metal matrix composite materials can be produced by powder metallurgy method. In this study, composite material with Al+12wt%Si matrix was produced by powder metallurgy (P/M) method. Al+12wt%Si powder was mixed by adding 5wt%, 10wt% and 15wt% Cr2O3 powder. Al+12wt%Si + Cr2O3 mixture powders were pressed unidirectional with 500MPa pressure in a cylindrical mold and sintered at 500 ºC. After sintering, optical microstructure, Scanning Electron Microscope (SEM), Energy Dispersive Spectrometer (EDS) and microhardness analyzes of the samples were made. When the results were examined, it was observed that a porous structure was formed in all of the samples. Moreover, the lowest amount of microhardness was measured in the sample added %15wt Cr2O3 powder sintered at 500 ºC.

Keywords:

Powder Metallurgy, Composite materials, Al, Cr2O3, Microstructure.,

PDF

___

[1]M. Yadav, L. A. Kumaraswamidhas, and S. K. Singh, “Investigation of solid particle erosion behavior of Al-Al2O3 and Al-ZrO2 metal matrix composites fabricated through powder metallurgy technique,” Tribol. Int., vol. 172, no. 107636, p. 107636, 2022.
[2] K. C. Nayak, P. R. Deshmukh, A. K. Pandey, P. Vemula, and P. P. Date, “Microstructural, physical and mechanical characterization of grinding sludge based aluminium metal matrix composite,” Mater. Sci. Eng. A Struct. Mater., vol. 773, no. 138895, p. 138895, 2020.
[3] I. Bahaj, M. Kaddami, A. Dahrouch, N. Labjar, and M. Essahli, “The effect of particle content and sintering time on the properties of Al-Al9Co2-Al13Co4 composites, made by powder metallurgy,” Mater. Today, vol. 62, pp. A1–A7, 2022.
[4] M. Ardestani and F. Karpasand, “Chemical synthesis and densification of a novel Ag/Cr2O3-AgCrO2 nanocomposite powder,” Sci. Eng. Compos. Mater., vol. 25, no. 4, pp. 739–743, 2018.
[5] O. Adıyaman, "Investigation of Mechanical Properties of Composite Al6061/Ni-Al2O3 Produced by Stir Casting Process", European Journal of Technique (EJT), vol. 12, no. 1, pp. 30-35, 2022.
[6] H. Su et al., “Research on high-temperature mechanical properties and microstructure of powder metallurgical rhenium,” Int. J. Refract. Hard Met., vol. 106, no. 105861, p. 105861, 2022.
[7] M. Boz ve A. Kurt, “Toz metal fren balata malzemelerinin sürtünme-aşınma performansı üzerine çinkonun etkisi,” Mühendislik Mimarlık Fakültesi Dergisi, vol. 21, no 1, p. 115-121, 2006.
[8] K. Köprülü, N. Mutlu, A. Kurt, B. Gülenç, Y. Özçatalbaş, “Al+%4,5 Cu ön karışımlı tozların alaşımlanmasına ısıl işlemlerin etkisi,” Gazi Uni. J. of Sci. Part C: Des. and Tech., vol. 6, no 2, p. 283-293, 2018.
[9] Y. Sayan, J.-S. Ki̇m, and H. Wu, “Residual stress measurement of a single-step sintered planar anode supported SC-SOFC using fluorescence spectroscopy,” Bitlis Eren Üniversitesi Fen Bilimleri Dergisi, vol. 11, no. 3, pp. 902–910, 2022.
[10] M. Kılıc, I. Kırık, M. Okumus, “Microstructure examination of functionally graded NiTi/NiAl/Ni3Al intermetallic compound produced by self-propagating high-temperature synthesis,” Kovove Mater., vol. 55, no 2, pp. 97–106, 2017.
[11] N. Kumar, A. Bharti, and K. K. Saxena, “A re-investigation: Effect of powder metallurgy parameters on the physical and mechanical properties of aluminium matrix composites,” Mater. Today, vol. 44, pp. 2188–2193, 2021.
[12] Ş. Çetinkaya, “Karbon katkılı alaşımlı demir tozu peletlerinin sinterleme sonrası özellikleri,” M.S. thesis, İstanbul Univ. Graduate Sch. of Nat. and App. Sci., İstanbul, Türkiye, 2005.
[13] Y. Sayan, V. Venkatesan, E. Guk, H. Wu, and J.-S. Kim, “Single-step fabrication of an anode supported planar single-chamber solid oxide fuel cell,” Int. J. Appl. Ceram. Technol., vol. 15, no. 6, pp. 1375–1387, 2018.
[14] E. Gevorkyan, L. Cepova, M. Rucki, V. Nerubatskyi, D. Morozow, W. Zurowski, V. Barsamyan and K. Kouril, “Activated sintering of Cr2O3-based composites by hot pressing”, Mater. , vol. 15, pp. 5960, 2022.
[15] K. Aslan, “Toz metalurjisi yöntemiyle Al+Si matrisli kompozitlerin aşınma dayanımlarının incelenmesi,” M.S. thesis, Bitlis Eren Univ. Inst. of Graduate Edu., Bitlis, Türkiye, 2022.
[16] M. Kılıç, “Toz metalurjisi ile Üretilen NiTi Alaşımına Al’un Etkisi,” Bitlis Eren Üniversitesi Fen Bilimleri Dergisi, vol. 10, no. 1, pp. 256-267, 2021.
[17] H. He, J. Lou, Y. Li, H. Zhang, S. Yuan, Y. Zhang, X. Wei, “Effects of oxygen contents on sintering mechanism and sintering-neck growth behaviour of FeCr powder,” Powder Techn., vol. 329, pp. 12-18, 2018.