Gain Increase of Horn Antenna with Waveguide Feeding Network by using 3D Printing Technology

2x1 array antenna with WFN (waveguide feeding network) by using 3D printing Technology and metal plating technique at X-Ku frequency band is proposed in the areas of radars, defense industry and satellite communication to increase antenna gain. The fabrication of 2x1 array antenna comprises of two processes which are to produce the structure of array antenna by using ABS for 3D printer and to carry out copper plating. Waveguide feeding network for array consists of a H-plane T-junction, two bend elements and three flanges. The spacing between the output terminals in waveguide feeding network is 3λ for better performance. There is a good agreement between measurement and simulation results by max 0.5dB difference because of surface roughness and high precision. The gain is increased by approximately1.5dB in comparison with single antenna. However, VSWR of the single antenna is 0.3dB lower than the array antenna. As a result, we have proposed the array antenna 90% lighter weight and 80% cheaper than metal equivalents.

Anahtar Kelimeler:

Horn antenna, T-junction waveguide, 3D printing technology, 3D Printer, Gain

Gain Increase of Horn Antenna with Waveguide Feeding Network by using 3D Printing Technology

2×1 array antenna with WFN (waveguide feeding network) by using 3D printing Technology and metal plating technique at X-Ku frequency band is proposed in the areas of radars, defense industry and satellite communication to increase antenna gain. The fabrication of 2×1 array antenna comprises of two processes which are to produce the structure of array antenna by using ABS for 3D printer and to carry out copper plating. Waveguide feeding network for array consists of an H-plane Tjunction, two bend elements and three flanges. The spacing between the output terminals in the waveguide feeding network is 3λ for better performance. There is a good agreement between measurement and simulation results by max 0.5dB difference because of surface roughness and high precision. The gain is increased by approximately1.5dB in comparison with a single antenna. However, VSWR of the single antenna is 0.3dB lower than the array antenna. As a result, we have proposed the array antenna 90% lighter weight and 80% cheaper than metal equivalents

Keywords:

Horn antenna T-junction, Waveguide, technology, 3D printer, Gain,

PDF

___

Balanis, C. A.: 'Horn antennas': 'Antenna theory: analysis and design' (John Wiley & Sons, 2005, 1st edn.), pp. 684-688
Bird, T. S.: 'Pyramidal horn': 'Fundamentals of aperture antennas and arrays: From theory to design, fabrication and testing' (John Wiley & Sons, 2016), pp. 79-81
Long, M., and Blake, B.: 'Horn radiator': 'Antennas: Fundamentals, design, measurement' (The Institution of Engineering and Technology, 2009), pp. 151-154
Timbie, P. T., Grade, J., Weide, D.V.D., et. al.: 'Stereolithographed mm-wave corrugated horn antennas'. Proc. 36th Int. Conf. on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz), Houston, TX, USA, Oct. 2011, pp. 1-3
Liang, M., Ng, W. R, Chang, K., et al.:'A 3-D luneburg lens antenna fabricated by polymer jetting rapid prototyping', IEEE Transactions on Antennas and Propagation, 2009, 62, (4), pp 1799-1807
Whittow, W., Njoku, C., and Vardaxoglou, J.: Patch antennas with heterogeneous substrates and reduced material consumption enabled by additive manufacturing techniques '. IEEE International Symposium on Antennas and Propagation and USNC URSI National Radio Science Meeting, Chicago, USA, July 2012, pp. 1-4
Sanz-Izquierdo, B., Parker, E. A.: '3-D printing of elements in frequency selective arrays', IEEE Transactions on Antennas and Propagation, 2014, 62, (12), pp 6060-6066
Gibson, I., Rosen, D., and Stucker, B.:' Additive manufacturing technologies rapid prototyping to direct digital manufacturing', Springer, 2010, 32, (2)
Selvan, K. T.: 'Accurate design method for optimum gain pyramidal horns', Electronics Letters, 1999, 35, (4), pp 249-250
Güney, K.: 'A new design method for optimum gain pyramidal horns', Electromagnetics, 2001, 21, (6), pp 497-505
Güney, K.: 'Improved design method for optimum gain pyramidal horns', International Journal of RF and Microwave Computer‐Aided Engineering, 2001, 11, (4), pp 188-193
Genc, A.:'Impedance matching of dielectric loaded T-junction in X-Ku band'. Proc. Int. Conf. on Signal Processing and Communication Application (SIU), Zonguldak, Turkey, May 2016, pp. 1-4.
Genc, A.: 'Design and manufacturing of X-Ku band horn array antenna and passive microwave components'. PhD thesis, Suleyman Demirel University, 2017.
Mallory, G. O, and Hajdu, J. B.: 'Fundamental aspects of electroless copper plating: 'Electroless plating: fundamentals and applications' (American electroplaters and surface finishers society inc, 1990), pp. 290-295
Basyigit, I. B, and Caglar, M. F.: 'Comprehensive analysis of shielding effectiveness of enclosures with apertures: Parametrical approach', Progress In Electromagnetics Research C, 2016, 70, pp 9-22
Garcia, C, Rumpf, R., Tsang, H. et. al.: 'Effects of extreme surface roughness on 3D printed horn antenna', Electronics Letters, 2013, 49, (12), pp 734-736
Castro A., Babakhani B., and Sharma S. 'Design and Development of a Multimode Waveguide Corrugated Horn Antenna Using 3D Printing Technology and its Comparison with Aluminium based Prototype', IET Microwaves, Antennas & Propagation, 2017, 11, (14), pp. 1977-1984