BaTiO 3 Epoksi Kompozit Malzemelerin Kapasitör Uygulamaları İçin Üretimi Ve Karakterizasyonu
Son yıllarda elektronik devrelerin üretim yoğunluğunun artması ile elektrik devrelerinin mikronmertebesinde küçültülmesine ihtiyaç duyulmuştur. Bu küçüklükteki bir elektronik devrenin çok yüksekbir performansa sahip olması gerekir. Dielektrik sabiti değeri yüksek olduğu bilinen BaTiO 3 (1200-1250Fm) yalıtkanlığı yüksek epoksi reçine ile güçlendirilirse kapasitörlerde kullanım alanı bulacak dielektriksabiti çok yüksek aynı zamanda dielektrik kayıbı çok düşük olan bir malzeme üretilebilir. Bunun içinöncelikle BaTiO 3 tozu geleneksel toz hazırlama yöntemlerine göre hazırlanır, daha sonra ağırlıkça %72,%70 ve %68 oranlarında BaTiO 3 , 1:2 ve 1:4 epoksi-sertleştirici oranına sahip reçinelerle birleştirilipkompozit malzeme olarak üretilir. Neticede dielektrik kayıbı düşük olan plakalarla elektrik kaçağınıminimum düzeye indirecek homojen ürünler elde edilmiştir.
Production and Characterization of BaTiO3 / Epoxy Composite Materials for Capacitor Applications
In recent years, it has been necessary to reduce the electric circuits in microns by increasing the production density of electronic circuits. This small electronic circuit must have a very high performance. BaTiO3 (1200-1250 Fm) insulation, which is known to have a high dielectric constant, will be strengthened with a high epoxy resin, which will produce a material with very high dielectric constant and very low dielectric loss at the same time. BaTiO3 powder will be prepared according to conventional powder preparation methods. Then it will be produced as composite material by combining resins with proportions of BaTiO3, 1: 2 and 1: 4 epoxy-hardener of 72%, 70% and 68% by weight. Plates with low dielectric loss will result in homogeneous products that will reduce electrical leakage to a minimum.
___
- Ananda K. S., Alagar M., Mohan V., 1999. Corrosion
resistance of siliconized-epoxy coatings.
European Coatings Journal, 5 : 45.
- Askeland D. R. “The Science and Engineering of
Materials” Missouri-Rolla Üniversitesi, 2002.
- Brzozowski, E. ve Castro, M.S., 2004. Influence of
Nb +5 and Sb +3 dopants on the defect profile,
PTCR effect and GBBL characteristics of BaTiO 3
ceramics, Journal of the European Ceramic
Society, 24, 2499-2507.
- Ho T. H., Wang C. S., 1999. Synthesis of aralkyl
novolac epoxy resins and their modification
with polysiloxane thermoplastic polyurethane
for semiconductor encapsulation. Journal of
Applied Polymer Science, 74 : 1905.
- Joshi NJ, Grewal GS, Shrinet V, Govindan TP, Pratap
A (2012). Synthesis and dielectric behavior of
nano-scale barium titanate, IEEE Trans.
Dielectr. Electr. Insul. 19, 83–90.
- Lin C. H., Chiang J. C., Wang C. S., 2003. Low
dielectric thermoset. I. Synthesis and
properties of novel 2,6-dimethyl phenoldicyclo
pentadiene epoxy. Journal of Applied Polymer
Science, 88 : 2607.
- Shi A, Yan W, Li Y, Huang K (2008). Preparation and
characterization of nanometer-sized barium
titanate powder by complex-precursor
method, J. Cent. South Uni. Technol. 15, 334–
338.
- Sung H., Lin C. Y., 1997. Polysiloxane modified
epoxy
polymer
Networks-I.
Graft
interpenetrating
polymeric
networks.,
European Polymer Journal, 33 : 903.
- Wang C. S., Liao J. K., 1991. Synthesis of high purity
o-cresol formaldehyde novolac epoxy resins.
Polymer Bulletin, 25 : 559.
- http://www.powertechnology.com., (14.03.2018)