Experimental analysis of laminated particleboard case-type furniture reinforced by polymer composite layer

In this study, the effects of reinforced corner joints by polymer composite layer in case-type furniture have been analyzed experimentally and statistically in laminated particleboard material. The failure loads of corner joints have been analyzed experimentally under compression and tension moments. These joint types are dowel (D), dowel+fabric from the outside (DCO), dowel+fabric from the inside (DCI), dowel+fabric from the outside and inside (DCOI), and dowel+fabric from the edge (DCE). The test results were analyzed statistically by Weibull distribution. Results show that the failure load takes its highest value in the DCOI case both for the test results and for 95% reliability under Weibull distribution. On the other hand, it takes its lowest value in the D case. Reinforced corner joints are more strength than unreinforced corner joints. In addition, the 95% reliability value for each corner joint configuration is approximately equivalent to the 0.52 value of the failure load.

Anahtar Kelimeler:

Composites, fabrics, reinforced, failure analysis, case-type furniture, corner joint

Experimental analysis of laminated particleboard case-type furniture reinforced by polymer composite layer

Keywords:

Composites, fabrics, reinforced, failure analysis, case-type furniture, corner joint,

PDF

___

Ghassan AC. Performance of wood members strengthened with fiber reinforced polymers (FRP). Research Structural Engineer ERDC-CERL, 2011: 37.
Heiduschke A, Cabrero JM, Manthey C, Haller P and Günther E. Mechanical behaviour and life cycle assessment of fibre-reinforced timber profiles. in: Braganca L, Koukkari H, Blok H, Cervasio R, Velkovic MR, Plewako UV, Landolfo Z, Silva L and Haller P. (Eds.) COST C25 Sustainability of Constructions Integrated Approach to Lifetime Engineering. COST C-25; European Commission: Dresden. 2008: 3.38–3.46.
Stevens ND and Criner GK. Economic analysis of fiber-reinforced polymer wood beams. Maine Agricultural and Forest Experiment Station. University of Maine. Bulletin 848. June 2000: 42.
Rowlands RE, Deweghe RP, Laufenberg TL and Krueger GP. Fiber-reinforced wood composites. Wood and Fiber Science, 1986; 18(1): 39 – 57.
Heiduschke A and Haller P. Load-carrying behavior of fiber reinforced wood profiles. World Conference on Timber Engineering, 2010: 7.
Cabrero JM, Heiduschke A and Haller P. Parametric analysis of composite reinforced wood tubes under axial compression. World Conference on Timber Engineering, 2010: 20 – 24.
Windorski DF, Doltis LA and Ross RJ. Feasibility of fiberglass-reinforced bolted wood connections. Res. Pap. FPL–RP–562: Madison: WI: U.S. Department of Agriculture. Forest Service. Forest Products Laboratory 1997: 9.
Norvydas V, Juodeikiene I and Minelga D. The influence of glued dowel joints construction on the bending moment resistance. Materials Science, 2005; 11(1): 36 – 39.
Liu WQ and Eckelman CA. Effect of number of fasteners on the strength of corner joints for cases. Forest Product Journal, 1998; 48(1): 93 – 95.
Tankut AN and Tankut N. Evaluation the effects of edge banding type and thickness on the strength of corner joints in case-type furniture. Materials and Design, 2010; 31: 2956 – 2963.
Yerlikaya NC and Aktas A. Enhancement of load-carrying capacity of corner joints in case-type furniture. Materials and Design, 2012; 37: 393 – 401.
Yerlikaya NC. Effects of glass-fiber composite, dowel, and minifix fasteners on the failure load of corner joints in particleboard case-type furniture. Materials and Design, 2012; 39: 63 – 71.
ASTM D 1037. Evaluating the properties of wood-base fiber and particle panel materials. ASTM, 1973.
Aktas A. Statistical analysis of bearing strength of glass-fiber composite materials. Journal of Reinforced Plastics and Composites, 2007; 26: 555 – 564.