Munise Didem Demirbaş, Mustafa Kemal APALAK

Numerical Solution of Thermal Residual Stress Analysis with Finite Difference Method of Functionally Graded Circular Plates

In this study, thermal residual stress analysis of functionally graded circular plates (FGCP) carried out. Finite difference equations are used in solving Navier's equations of elasticity and Fourier's heat conduction equation. The grading along the plate was made along the surface of plate and it was assumed that the material properties changed according to the Mori-Tanaka approach. Grading along the plate was made in both radial and tangential directions. In this study, the effect of the coordinate derivatives of material properties was taken into consideration in both Fourier's heat conduction equation and Navier's equations of elasticity, unlike the other studies. As a result, when the materials compositions of FGCP were changed from ceramic-rich to metal-rich compositions, the stress levels were not affected considerably. The strain levels increased significantly when the metal compound in the material composition of FGCP was increased. FGCP are emphasized that the change of material properties due to two-dimensional significantly affect distributions of thermal strain and stress. In this study, it was emphasized that changing the radial and tangential direction of the compositional gradient exponents of FGCP subjected to heat flux along the outer edge significantly influences the strain and stress distributions.

Keywords:

Functionally graded circular plates Two-dimensional-FGM, Finite difference methods,

PDF

___

Noda, N. (1999). Thermal stress intensity factor for functionally gradient plate with an edge crack. Journal of Thermal Stresses, 22(4-5), 477-512. Choules, B.D., & Kokini, K. (1996). Architecture of functionally graded ceramic coatings against surface thermal fracture. Journal of Engineering Materials and Technology, 118(4), 522-528.
Apalak, M.K., & Demirbas, M.D. (2013). Thermal residual stresses in adhesively bonded in-plane functionally graded clamped circular hollow plate. Journal of Adhesion Science and Technology, 27(14),1590-1623.
Wang, B.L., Mai, Y.W., & Zhang, X.H. (2004). Thermal shock resistance of functionally graded materials. Acta Materialia, 52(17), 4961-4972. Moosaie, A. (2016). A nonlinear analysis of thermal stresses in an incompressible functionally graded hollow cylinder with temperature-dependent material properties. European Journal of Mechanics A/Solids, 55, 212-220.
Mahdavia, E., Ghasemib, A., & Akbari Alashtic, R. (2016). Elastic-plastic analysis of functionally graded rotating disks with variable thickness and temperature-dependent material properties under mechanical loading and unloading. Aerospace Science and Technology, 59, 57-68. Najibi, A., & Talebitooti, R., (2017). Nonlinear transient thermo-elastic analysis of a 2D-FGM thick hollow finite length cylinder. Composites Part B: Engineering, 111, 211-227.
Burlayenko, V.N., Altenbach, H., Sadowski, T., Dimitrova, S.D., & Bhaskar, A. (2017). Modelling functionally graded materials in heat transfer and thermal stress analysis by means of graded finite elements. Applied Mathematical Modelling, 45, 422-438.
Swaminathan, K., Sangeetha, D.M. (2017). Thermal analysis of FGM plates - A critical review of various modeling techniques and solution methods. Composite Structures, 160, 43-60.
Ghannad, M., Parhizkar Yaghoobi, M. (2017). 2D thermo elastic behavior of a FG cylinder under thermomechanical loads using a first order temperature theory. International Journal of Pressure Vessels and Piping, 149, 75-92.
Iwasawa C., Nagata, M., Seino, Y., & Ono, M. (1997). A study on anode materials and structures for SOFC. Proceedings of the Fifth International Symposium on Solid Oxide Fuel Cells (SOFC-V), 97(40), 626-634.
Wang, Y., Chen, K.S., Mishler, J., Cho, S.C., & Adroher, X.C. (2011). A review of polymer electrolyte membrane fuel cells: Technology, applications, and needs on fundamental research. Applied Energy, 88(4), 981-1007.
Kakac, S., Pramuanjaroenkij, A., & Zhou, X.Y. (2007). A review of numerical modeling of solid oxide fuel cell. International Journal of Hydrogen Energy, 32(7), 761-786. Ruys, A., Popov, E., Sun, D., Russell, C., & Murray, C. (2001). Functionally graded electrical/thermal ceramic systems. Journal of the European Ceramic Society, 21(10-11), 2025-2029.
Noda, N. (1997). Thermal stresses intensity factor for functionally gradient plate with an edge crack. J. Therm. Stresses, 20, 373-387. Nemat-Alla, M. (2003). Reduction of thermal stresses by developing two-dimensional functionally graded materials. International Journal of Solids and Structures, 40(26), 7339-7356.
Tomota, Y., Kuroki, K., Mori, T., & Tamura T. (1976). Tensile deformation of two-ductile-phase alloys: flow curves of ? -> ? Fe-Cr-Ni alloys. Mater. Sci. Eng., 24, 85-94. K. Wakashima, K., & Tsukamoto, H. (1991). Mean-field micromechanics model and its application to the analysis of thermomechanical behavior of composite materials. Mater. Sci. Eng. A, 146, 291-316.
Levin, V.M. (1967). On the coefficients of thermal expansion of heterogeneous material. Mech. Solids., 2, 88-94.
Mori, T., & Tanaka, K. (1973). Average stress in matrix and average elastic energy of materials with misfittings inclusions. Acta Metallurgica, 21(5), 517-574.
Materials Information Resource MatWeb [Online]. Available: http://www.matweb.com, 2016.
MATLAB. Mathematical software, version 2009a, TheMathWorks, 2009.