Ruijin LIAO, Ende HU, Lijun YANG, Lian DUAN

The process of creeping discharge-caused damage on oil/pressboard insulation

This paper presents experimental research on creeping discharge by using cylinder-plate electrode configurations under AC voltages. The process of creeping discharge-caused damage on the oil/pressboard insulation was studied. First, the electric field distribution was achieved by Multiphysics software simulation. Afterwards, the phenomena that occurred in the entire damage process, such as white smoke , white mark , and black mark , were recorded and analyzed. Furthermore, the micromorphology of the oil-impregnated pressboard was observed via scanning electron microscope (SEM). Finally, the inner mechanism of the damage to the oil/pressboard insulation was explored according to the phenomena and the SEM morphologies. Results showed that during damage processes, the high electrical field strength (nearly 25.853 MV/m) at the weak-link point between the cylinder electrode and the pressboard directly caused the incipient discharge. The cavity, moisture, impurity, solid particle, and formation of a gaseous channel all contributed to the development of the damage. The white smoke consisted of gases that stemmed from the ionization of oil and evaporation of moisture. The white mark was the gas channel and pressboard carbonization was caused by discharge and high temperature, both of which were also the main causes of the emergence of black mark . SEM images revealed that the pressboard successively experienced white solid , crack , and pitting , which changed its surface roughness. The distorted electric field caused by gases, solid particles, and pitting further damaged the oil/pressboard. The pitting evolved into the starting point of the electrical trees and gradually led to the final breakdown.

PDF

___

[1] Liao RJ, Liang S, Sun CX, Yang LJ, Sun H. A comparative study of thermal aging of transformer insulation paper impregnated in natural ester and in mineral oil. Eur T Electr Power 2010; 20: 518533.
[2] Saha TK. Review of modern diagnostic techniques for assessing insulation condition in aged transformers. IEEE Trans Dielectr Electr Insul 2003; 10: 903917.
[3] Seytashmehr A, Fofana I, Eichler C, Akbari A, Borsi H, Gockenbach E. Dielectric spectroscopic measurements on transformer oil-paper insulation under controlled laboratory conditions. IEEE T Dielectr Electr Insul 2008; 15:11001111.
[4] Junichi W, Akitoshi N, Hideyuki M, Tadasu T, Satoru Y, Shigemitsu O, Masanori K. Surface breakdown characteristics of silicone oil for electric power apparatus. IEEE T Dielectr Electr Insul 2006; 13: 830837.
[5] Peter M. Assessment of dielectric degradation by ultrawide-band pd detection. IEEE T Dielectr Electr Insul 1995; 2: 744769.
[6] Yan JM, Liao RJ, Yang LJ, Li J. Study on microstructure and electrical properties of oil-impregnated paper insulation after exposure to partial discharge. Eur T Electr Power 2012; 22: 733746.
[7] Liao RJ, Yan JM, Yang LJ, Zhu MZ, Liu B. Study on the relationship between damage of oil-impregnated insulation paper and evolution of phase-resolved partial discharge patterns. Eur T Electr Power 2011; 21: 21122124.
[8] Yan JM, Liao RJ, Yang LJ, Zhu MZ. Measurements and analysis of surface damage on oil-impregnated insulation paper caused by partial discharge. Meas Sci Technol 2011; 22: 5570355712.
[9] Mitchinson PM, Lewin PL, Strawbridge BD. Tracking and surface discharge at the oil/pressboard interface. IEEE Electr Insul M 2010; 26: 3541.
[10] Mitchinson PM, Lewin PL, George C, Jarman PN. A new approach to the study of surface discharge on the oil-pressboard interface. In: IEEE 2008 International Conference on Dielectric Liquids; 30 June3 July 2008; Futuroscope-Chasseneuil, France. New York, NY, USA: IEEE. pp. 14.
[11] Zainuddin H, Lewin PL, Mitchinson PM. Partial discharge characteristics of surface tracking on oil-impregnated pressboard under ac voltages. In: IEEE 2013 International Conference on Solid Dielectrics; 30 June4 July 2013; Bologna, Italy. New York, NY, USA: IEEE. pp. 10161019.
[12] Wang W, Bao B, Xu JF, Zhou B, Li CR. Creepage discharge performance for high moisture pressboard. In: IEEE 2011 Annual Report Conference on Electrical Insulation and Dielectric Phenomena; 1619 October 2011; Cancun, Mexico. New York, NY, USA: IEEE. pp. 480483.
[13] Wang W, Xue Y, Cheng YC, Zhou B, Xu JF, Li CR. Diagnosis of severity degree for oil/pressboard insulation surface discharge. In: IEEE 2012 Annual Report Conference on Electrical Insulation and Dielectric Phenomena; 1619 October 2011; Cancun, Mexico. New York, NY, USA: IEEE. pp. 472475.
[14] Ghaffarian M, Clemence R, Wang X, Nikjoo R, Edin H. Effect of temperature on surface discharge in oil. In: IEEE 2012 Annual Report Conference on Electrical Insulation and Dielectric Phenomena; 1417 October 2012; Montreal, Canada. New York, NY, USA: IEEE. pp. 9699.
[15] Beroual A, Viet-Hung D. Fractal analysis of lightning impulse surface discharges propagating over pressboard immersed in mineral and vegetable oils. IEEE T Dielectr Electr Insul 2013; 20: 14021408.
[16] Viet-Hung D, Beroual A, Coulibaly ML, Perrier C. Investigation on creeping discharges propagating over pressboard immersed in mineral and vegetable oils submitted to lightning impulse voltages. In: IEEE 2012 International Conference on Condition Monitoring and Diagnosis; 2327 September 2012; Bali, Indonesia. New York, NY, USA: IEEE. pp. 404407.
[17] Rebia¨ı S, Bahouh H, Sahli S. 2-D simulation of dual frequency capacitively coupled helium plasma using COMSOL Multiphysics. IEEE T Dielectr Electr Insul 2013; 20: 16161624.
[18] Hsieh CT, Wang MH, Pan CY. Applying the finite element method to analyze pre-discharge lightning rods. Turk J Electr Eng Co 2011; 19: 621629.
[19] Ergene L, Nelson JK, Parthasarathi R. Finite element modeling of a superconducting fault current limiter. Turk J Electr Eng Co 2012; 20: 842853.
[20] Sima WX, Peng QJ, Yang Q, Yuan T, Shi J. Study of the characteristics of a streamer discharge in air based on a plasma chemical model. IEEE T Dielectr Electr Insul 2012; 19: 660670.
[21] Pancheshnyi S, Nudnova M, Starikovskii A. Development of a cathode-directed streamer discharge in air at different pressures: experiment and comparison with direct numerical simulation. Phys Rev E 2005; 71: 112.
[22] Wechsler K, Riccitiello M. Electric breakdown of a parallel solid and liquid dielectric system. AJEE Trans Power App 1961; 80: 365368.
[23] Dai J, Wang ZD, Jarman P. Creepage discharge on insulation barriers in aged power transformers. IEEE T Dielectr Electr Insul 2010; 17: 13271335.
[24] Zainuddin H, Mitchinson PM, Lewin PL. Investigation on the surface discharge phenomenon at the oil/pressboard interface. In: IEEE 2011 International Conference on Dielectric Liquids; 2630 June 2011; Trondheim, Norway. New York, NY, USA: IEEE. pp. 14.
[25] Yan JM, Liao RJ, Yang LJ, Liu B. Product analysis of partial discharge damage to oil-impregnated insulation paper. Appl Surf Sci 2011; 257: 58635870.