Yönetmeliklerdeki Taşıma Gücü Yöntemleri

Eğilme ve bileşik eğilme etkisindeki kesitlerin taşıma gücüne göre hesaplanması ülkemizde yönetmeliklerin getirdiği bir zorunluluktur. Birçok konuda olduğu gibi bu konuda da ulusal yönetmelikler ABD yönetmeliği (ACI-318) ve Avrupa yönetmeliklerinden etkilenmiştir. Bu makalede, eğilme ve bileşik eğilme altındaki kesitlerin taşıma gücüne göre hesabı irdelenecektir. Bu kapsamda TS-500, ACI-318 ve Eurocode 2’nin ilgili hükümleri tanıtılacak ve bu üç yönetmelikten elde edilen sonuçlar karşılaştırılacaktır.

Code Requirements for Ultimate Stress Design

Turkish reinforced concrete and seismic codes enforce the use of “ultimate strength design” for the analysis and design of reinforced concrete cross-sections. In this paper, assumptions made for calculating the ultimate strength of sections under pure bending and combined bending in different codes are discussed. Ultimate moments obtained using the requirements of TS-500, ACI-318 and Eurocode 2 are compared.

___

  • Hognestad, E. , “Fundamental Concepts in Ultimate Load Design of Reinforced Concrete Members,” Proceedings of American Concrete Institute (ACI), V.23, No.10, June 1952, Detroit, Michigan.
  • Spater, W.A., and Lyse, I., “Column Tests at Lehigh University,” Journal of ACI, March 1931, Nov. 1931, January 1932, Detroit, Michigan
  • Whitney, C.S., “Plastic Theory of Reinforced Concrete Design,” Trans. of ASCE, V68, p 251, 1942
  • Ersoy, U., Tankut, T., Atımsay, E., Aktan, E., ve Erbatur, F., “Betonarme Yapıların Taşıma Gücü İlkesiyle Hesap ve Yapım Kuralları,” Bayındırlık Bakanlığı, Proje no: 77-04-03-55, Bayındırlık Bakanlığı yayını, Ankara 1979.
  • “Betonarme Yapıların Hesap ve Yapım Kuralları, TS-500-2000,” Türk Standartları Enstitüsü, Ankara 2000.
  • “Building Code Reguirements for Structural Concrete (ACI 318-11), Detroit, Michigan, 2011.
  • “Design of Concrete Structures-Concrete Bridges.Design and Detailing Rules, Eurocode 2 , European Standard, 2005.
  • Hisham, H.H.I. and Mac Gregor J.G.,”Modification of ACI Rectangular Stress Block for High-Strength Concrete,” ACI Structural Journal, January-February 1997 Detroit, Michigan
  • Bae,S.,and Bayrak,O., “Stess Block Parameters for High-Strength Concrete Members,” ACI Structural Journal, Sptember-October 2003. Detroit, Michigan
  • Hisham, H.H.I. and Mac Gregor, J.C “Tests of Eccentrically Loaded High Strength Concrete Columns,” ACI Structural Journal, Sptember/October, 1996, Detroit, Michigan
  • Foster, S.J., and Attard, M.M. , “Experimental Tests on Eccentrically Loaded High Strength Concrete Columns,” ACI Structural Journal, May-June 1997. Detroit, Michigan
  • Çokça, E., “Strength of Reinforced Concrete Columns Under Biaxial Bending,” MS Thesis, METU Civil Eng. Dept., 1984, Ankara
  • Ersoy, U. , “Taşıma Gücü Varsayımları ile İlgili Bir İrdeleme,” İMO Teknik Dergi Yazı no.4, 1990