Porland kalkerli çimento bölüm I - çimentoların hazırlanması

Bu makale TÜBİTAK tarafından desteklenen “Portland Kalkerli Çimento Üretiminde Mekanik Performans ve Sülfat Kaynaklı Durabilite Problemleri Açısından Optimum Kalker Oranının Belirlenmesi” konulu proje bulgularının sunulduğu çalışmanın birinci bölümüdür. Bu bölümde, %5’den %40’a kadar değişen oranlarda kalker katkısı içeren çimentolar hazırlanmıştır. Çimentoların hazırlanmasında karşılaşılan sorunlar ve kalker ikamesinin hazırlanan harçların fiziksel ve mekanik özelliklerindeki meydana getirdiği değişiklikler araştırılmıştır. Kalker katkısı oranının artışıyla, tane boyut dağılımının daha geniş bir aralığa yayıldığı belirlenmiştir. Blaine değerinin artmasına rağmen, kalker oranı artışı ile incelik (32 mm elek üstü) değerinin de arttığı gözlenmiştir. Hazırlanan harçların kıvamında bir yapışkanlık ve sakızlanma meydana gelmiştir. Ayrıca, kalker miktarının artışıyla birim hacim ağırlıklarda azalma, su emme değerlerinde artma ve tüm yaşlardaki basınç dayanımında düşüş görülmüştür.

Portland limestone cement part I - preparation of cements

This paper is the first part of a research project which was supported by TUBITAK titled “Determination of Optimum Limestone Content in Portland Limestone Cement Production from the View Point of Mechanical Performance and Sulfate Originated Durability Problems”. In this stage, blended cements incorporating different amounts of limestone powders from 5 to 40% were prepared. The problems observed in the preparation stage of limestone blended cements and the effects of limestone replacement on the physical and mechanical properties were investigated. Increasing of limestone replacement ratios resulted in a wider particle size distribution. In contrast with the increases in Blaine values, fineness (residue at 32 μm) values of cements have also increased. Mortars had a sticky and cohesive consistency. Also, increasing the limestone incorporation caused decreases in unit weights and compressive strength values of mortars with a parallel increase in water absorption values at all ages.

___

  • [1] Yeğinobalı, A., Ertün, T., New Standards for cement and mineral admixtures. TÇMB Institute of R&D, Ankara, 2004 (in Turkish).
  • [2] Tsivilis, S., Chaniotakis, E., Badogiannis, E., Pahoulas, G., Ilias, A., A Study on The Parameters Affecting The Properties of Portland Limestone Cements. Cement and Concrete Composites, 21, 107-116, 1999.
  • [3] Voglis, N., Kakali, G., Chaniotakis, E., Tsivilis, S., Portland-Limestone Cements. Their Properties and Hydration Compared to Those of Other Composite Cements. Cement and Concrete Composites, 27, 191–196, 2005.
  • [4] Tsivilis, S., Chaniotakis, E., Kakali, G., Batis, G., An Analysis of Properties of Portland Limestone Cements and Concrete. Cement and Concrete Composites, 24, 371–378, 2002.
  • [5] İnan Sezer, G., Effects of Limestone and Clinker Properties on the Properties of Limestone Blended Cement. PhD Thesis, Ege University, Institute of Applied Sciences, İzmir, 2007, (in Turkish).
  • [6] Erdoğdu, K., Hydration Properties of Limestone İncorporated Cementitious Systems. PhD. Thesis, METU, Civil Engineering Department, Ankara, 2002.
  • [7] Dhir, R.K., Limbachiya, M.C., McCarthy, M.J., Chaipanich, A., Evaluation of Portland Limestone Cements for Use in Concrete Construction. Materials and Structures, 40, 459–473, 2007.
  • [8] Rahhal, V., Tolero, R., Early Hydration of Portland Cement with Crystalline Mineral Additions. Cement and Concrete Research, 35, 1285-1291, 2005.
  • [9] Yahia, A., Tanimura, M., Shimoyama, Y., Rheological Properties of Highly Flowable Mortar Containing Limestone Filler-Effect of Powder Content and W/C Ratio. Cement and Concrete Research, 35, 532-539, 2005.
  • [10] Poppe, A.M., Schutter, G.D., Cement Hydration in The Presence of High Filler Contents. Cement and Concrete Research, 35, 2290-2299, 2005.
  • [11] Bentz, D.P., Modeling The Influence of Limestone Filler on Cement Hydration Using CEMHYD3D. Cement and Concrete Composites, 28, 124-129, 2006.