Nevin KARAMAHMUT MERMER, Müge SARI YILMAZ, Sabriye PİŞKİN

PREPARATION OF GAS CONCRETE MATERIALS FROM VARIOUS INDUSTRIAL WASTE

Construction materials are being used primarily for the humans’ basic shelter needs since the beginning of history. Also, construction sector continues to evolve with the constantly advancing technology and it is one of the most important and largest sectors together with textile and food in the world. Gas concrete, which is a type of lightweight concrete’s, usage has increased due to its minimal energy losses and light weight. With the additives that uses in gas concrete and creating pores with them, the structure can gain lightness and insulating properties. In this study, the gas concrete samples have been prepared with different methods using various industrial wastes as aggregate. Two different mixing types including by hand and with mechanical stirrer were used to see the impact of mixing type to the strength. Characterization and compressive strength values of the prepared samples were determined by comparing the best aggregate types. Gas concrete has been prepared both under the pressure and temperature in autoclaved conditions and the room conditions separately to see the effect of using the autoclave. According to analysis result, the gas concrete sample prepared from Afsin Elbistan fly ash and sand mixture had the best compressive strength of 1.09 N/mm2 and it was classified as G1 class regarding to TS 453.

Keywords:

Gas concrete gold mine tailing slurry, fly ash, lightweight concrete,

PDF

___

[1] Ünsal A., Şen H., “Beton ve Beton Malzemeleri Laboratuvar Deneyleri”, T.C Ulaştırma Bakanlığı Karayolları Genel Müdürlüğü, 2008.
[2] Özden K., Betonarme 1, Teknik Üniversite Matbaası, İstanbul, 1971.
[3] Türkel S., “Özel Betonlar, Hafif Beton”, TMMOB İnşaat Mühendisleri Odası İzmir Şubesi Haber Bülteni, 2007.
[4] Khaw Yong H., “Performance Of Lightweight Foamed Concrete Using Laterite As Sand Replacement”, Faculty of Civil Engineering & Earth Resources, Universiti Malaysia Pahang.
[5] Mohd Roji S., “First report research project on lightweight concrete”, Universiti Teknologi Malaysia, Skudai, Johor Bahru, 1997.
[6] Ismail H. K. M., Fathi M. S., Manaf N. B., “Study of lightweight concrete behavior”, Universiti Teknologi Malaysia.
[7] Yilmaz Sari M., Mermer Karamahmut N., “Conversion of fly ashes from different regions to mesoporous silica: effect of the mineralogical composition”, J Sol-Gel Sci Technol 78:239–247, 2016.
[8] Yilmaz Sari M., Piskin S., (2013) Extraction of Silicon Dioxide from Tailings Slurry of Gold Mine Treatment Plant by Alkali Fusion Technique, International Journal of Chemical, Environmental and Biological Sciences, Vol. 1, Issue 2, pp 211-213.
[9] Guo X., Shi H., Dick W. A., “Compressive strength and microstructural characteristic of class c fly ash geopolymer”, Cem. Concr. Compos, 32:142–147, 2010.
[10] Palomo A., Blanco-Varela M. T., Granizo M. L., Puertas F., Vazquez T., Grutzeck M. W., “Chemical stability of cementitious materials based on metakaolin”, Cem. Concr. Res., 29:997–1004, 1999.
[11] Atalay S., Adiguzel H. I., Atalay F., “Infrared Absorption Study Of Fe2O3–CaO–SiO2 Glass Ceramics”, Materials Science and Engineering, A304–306, 796–799, 2001.
[12] Gomes C. E. M., Ferreira O. P., “Analyses of microstructural proporties of va/veova copolymer modified cement pastes”, Polimeros: Ciencia E Tecnologia, 15 (3): 193-198, 2005.
[13] Narayanan N.,, Ramamurthy K., “Structure and properties of aerated concrete: a review”, Cement and Concrete Composites, 22, 5, 321–329, 2000.
[14] Uysal M., Gundogdu B. C., Sumer M., “Gazbetonun kuruma rötresine bağlayıcı malzeme miktarı değişiminin etkisi”, Erciyes Üniversitesi Fen Bilimleri Enstitüsü Dergisi, 28(4):303-308, 2012.

Sigma Mühendislik ve Fen Bilimleri Dergisi-Cover

ISSN: 1304-7191
Yayın Aralığı: Yılda 4 Sayı
Yayıncı: Yıldız Teknik Üniversitesi

Arşiv