Rami Reddy PADALA V, Kesava RAO V. V. S.

Investigation on effect of tig welding parameters on dissimilar weld joints of aisi 304 and aisi 310 steels using response surface method

However efficient welding of dissimilar metals has posed a major challenge due to difference in thermal, mechanical and chemical properties of the materials to be joined under a common welding condition. In the present work dissimilar joints of AISI 304 and AISI 310 steels are produced using Tungsten Inert Gas (TIG) welding. Welding current, wire feed rate, flow rate of gas and edge included angle are considered as input parameters and tensile strength, Impact strength and Maximum bending load are considered as output respo nses. Response Surface Method (RSM) is adopted using Central Composite Design (CCD) and 31 experiments were performed for 4 factors and 5 levels. Tensile strength, impact strength and maximum bending load are measured. Analysis of Variance (ANOVA) is carried out at 95% confidence level. Effect of welding parameters on output responses are studied by drawing main effect plots, contour plots and surface plots. Optimal weld parameters are identified using Response optimizer.

Keywords:

Dissimilar welds, AISI 30 4, AISI 310 steels, TIG welding,

PDF

___

[1] Atul Kumar, Vikrant Sharma, N. S. Baruaole, Experimental investigation of TIG welding of stainless steel 202 and stainless steel 410 using Taguchi Technique, International Journal of Computing and Engineering Research, 1(2), 2017, pp. 98-101.
[2] Iqbaljeet Singh Grewal, Amrinder Singh, Prabhjot Singh, Experimental Investigation of welding parameters and mechanical properties by Taguchi Method of TIG welded EN 31 Steel and Mild Steel, International Journal of Engineering Applied Sciences and Technology, 2(4), 2017, pp. 164-171.
[3] I Owunna and A. E. Ikpe, Modelling and Prediction of the mechanical properties of TIG welded joint for AISI 4130 low carbon steel plates using Artificial Neural Network (ANN) approach, Nigerian Journal of Technology, 38(1), 2019, pp. 117-126.
[4] Mukesh Hemnani, Promise Mittal, Sachin Goyal, Optimization of Tungsten Inert Gas Welding using Taguchi and ANOVA, International Journal for Research in Applied Science & Engineering Technology, 6(V), 2018, pp. 2807-2811.
[5] K. Nageswararao, B. V. R. Ravi Kumar, M. T. Naik, Study and parameter optimization of dissimilar materials using MIG Welding Process, International Journal of Engineering and Techniques, 4(2), 2018, pp. 1081-1085.
[6] Baljeet Singh, Pankaj Kumar, S. K. Kumara Swamy, Uday Krishna Ravella and Anil Midathda, Microstructure characteristics & mechanical properties of dissimilar TIG weld between Stainless Steel and Mild Steel, International Journal of Mechanical Engineering and Technology, 8(7), 2017, pp. 1739–1747. http://www.iaeme.com/IJMET/issues.asp?JType=IJMET&VType=8&IType=7.
[7] S. Mohan Kumar and N. Siva Shanmugam, Studies on the weldability, mechanical properties and microstructural characterization of activated flux TIG welding of AISI 321 Austenitic Stainless Steel, Materials Research Express, 2018, pp. 1-58.
[8] G. Venkatesan, Jimin George, M. Sowmyasri, V. Muthupandi, Effect of ternary fluxes on depth of penetration in A-TIG welding of AISI 409 ferritic stainless steel, Procedia Materials Science, 5 , 2014, pp. 2402 – 2410.
[9] Mukesh, Sanjeev Sharma, Study of Mechanical Properties in Austenitic Stainless Steel Using Gas Tungsten Arc Welding (GTAW), Int. Journal of Engineering Research and Applications, 3(6), 2013, pp. 547-553.
[10] Salah Sabeeh Abed Alkareem, An investigation of generated heat flux during welding with and without fillers using different welding conditions, International Journal of Simulation Systems, Science & Technology, 20(4),2019, pp. 1 to 6.
[11] Mohamed Farid Ben Lamnouar, Mohamed Hadji, Riadbadji, Nabilbensaid, Taharsaadi, Yazid Laibditlaksir, Sabah Senouci, Optimization of TIG welding process parameters for X70-304l dissimilar Joint using Taguchi Method, Solid State Phenomena, 297, 2019, pp. 51-61.
[12] S. C. Juang And Y. S. Tarng, Process parameter selection for optimizing the weld pool geometry in the tungsten inert gas welding of stainless steel, Journal of Materials Processing Technology, 122, 2002, pp. 33–37.
[13] Wichan Chuaiphan, Somrerk Chandra-Ambhorn, Satian Niltawach, C. and Banlengsornil, Dissimilar Welding between AISI 304 Stainless Steel and AISI 1020 Carbon Steel Plates, Applied Mechanics and Materials, 268-270, 2013, pp. 283-290.
[14] Ajay Kumar, Pradeep Kumar, Srishti Mishra, R. K. Mishraatushar Srivastav, Sachin Mishra Rajeev Kumar, Experimental Process of Tungsten Inert Gas Welding of a Stainless Steel Plate, Materials Today: Proceedings, 2, 2015, pp. 3260-3267.
[15] C. Balaji, S. V. Abinesh Kumar, S. Ashwin Kumar, R. Sathish, Evaluation of mechanical properties of SS 316L weldments using Tungsten Inert Gas welding, International Journal of Engineering Science and Technology, 4(5), 2012, pp. 2053- 2057.
[16] Piyush Rana, Baljinder Singh, Jaswant Singh, Parametric Study of Dissimilar Material on Gas Tungsten Arc Welding, International Journal of Engineering Sciences, 25, 2017, pp. 60-67.