Effect of Heat Treatment on Microstructure of Zinc Aluminum Hybrid Composite Cast Alloys

The matrix material ZA27 alloy was used in the production of metal matrix composite material. SiC and graphite were used as reinforcement materials in the study. ZA27 alloy with 10% SiC, 2.5% , 5% , 7.5% and 10% graphite and 10% SiC + 2.5% , 5%, 7.5%, 10% graphite reinforcement by weight hybrid composite material was produced. The microstructures were examined by SEM and EDS and the results were discussed. In the investigations, SiC and graphites had a heterogeneous nucleating effect during the solidification of the alloy. In addition, thin dendrites showed a tendency to become spherical by heat treatment.

Keywords:

ZA alloy casting, Heat Treatment, Composite Hybrid Casting,

PDF

___

[1] Demirkesen, E., Kompozit Malzemeler, İTÜ Kimya Fakültesi, 1.Baskı s.1-5, 1991.
[2] S.S. Owoeye, D.O. Folorunso, B. Oji, S.G. Borisade, “Zinc-Aluminum (ZA-27)-based metal matrix composites: a review article of synthesis, reinforcement, microstructural, mechanical, and corrosion characteristics,” Int. J. Adv. Manuf. Technol. 100 (2019) 373–380. https://doi.org/10.1007/s00170- 018-2760-9.
[3] S. S. Owoeye, D. O. Folorunso, B. Oji, and S. G. Borisade, “Zinc-aluminum (ZA-27)- based metal matrix composites: a review article of synthesis, reinforcement, microstructural, mechanical, and corrosion characteristics,” Int. J. Adv. Manuf. Technol., vol. 100, no. 1–4, pp. 373–380, 2019, doi: 10.1007/s00170-018-2760-9.
[4] S. Sastry, M. Krishna, and J. Uchil, “Study on damping behaviour of aluminite particulate reinforced ZA-27 alloy metal matrix composites,” J. Alloys Compd., vol. 314, no. 1–2, pp. 268–274, 2001, doi: 10.1016/S0925-8388(00)01235-4.
[5] R. Arikan, “Saffı̇l (η-Al2O3) fiber takvı̇yelı̇ ZA-12 alaşimin sürtünme aşinma davranişlari,” J. Fac. Eng. Archit. Gazi Univ., vol. 22, no. 3, pp. 359–368, 2007.
[6] M. Gelfi, E. Bontempi, A. Pola, R. Roberti, D. Rollez, and L. E. Depero, “Microstructural and mechanical properties of zinc die casting alloys,” Adv. Eng. Mater., vol. 6, no. 10, pp. 818–822, 2004, doi: 10.1002/adem.200400087.
[7] M.R. Monteiro, A.R.P. Ambrozin, A.O. Santos, P.P. Contri, S.E. Kuri, “Evaluation of Metallic Corrosion Caused by Alcohol Fuel and Some Contaminants,” Materials Science Forum, Vol 636 – 637, 1024-1029, 2010.
[8] A. Pola, R. Roberti, L. Montesano, ‘New Zinc alloys for semisolid applications’, International Journal of Material Forming, 2010, Volume 3, Supplement 1, 743-746.
[9] Alüminyum Hibrit Kompozit Malzemelerin Aşınma Davranıışlarının İncelenmesi, Doktora Tezi, Sakarya Üniversitesi Fen Bilimleri Enstitüsü, 2004.
[10] S. C. Sharma, B. M. Girish, R. Kamath, and B. M. Satish, “Effect of SiC particle reinforcement on the unlubricated sliding wear behaviour of ZA-27 alloy composites,” Wear, vol. 213, no. 1–2, pp. 33–40, 1997, doi: 10.1016/S0043- 1648(97)00185-3.
[11] Sharma, S., C., Sastryb, S., Krishna, M., Effect of Aging Parameters on the Micro Structure and Properties of ZA-27/ Aluminite Metal Matrix Composites, Journal of Alloys and Compounds 346, 292– 301, 2002.
[12] Miroslav, B., Vencl, A., Mitrovic, S:, Bobic, I., “Influence of T4 Heat Treatment on Tribological Behavior of Za27 Alloy Under Lubricated Sliding Condition,” Tribol Lett, 36:125–134, 2009.
[13] Metallography and Microstructures of Zinc and Its Alloys, Metallography and Microstructures, Vol 9, ASM Handbook, ASM International, ,p. 933– 941, 2004.
[14] Jovanovic, M. T., Bobiç, I., Djurcic, B. Grahovac, N., “Microstructural and Sliding Wear Behaviour of a Heat-Treated ZincBased Alloy”, Tribology Letters, Volume 25, Number 3, 173-184, 2007.
[15] Pürçek, G., “Çinko-Aliminyum Esaslı AlaĢımlardan Üretilen Kaymalı Yatakların Tribolojik Özelliklerinin incelenmesi”, Yüksek Lisans Tezi, Karadeniz Teknik Üniversitesi, 1994.
[16] Akbulut, H., Altunpak, Y., “Alümina Kısa Fiber Takviyeli Al Esaslı LM 13 Alaşımında Yaşlandırma Isıl İşlem Özellikleri Optimizasyonu,” Teknoloji, Cilt 8, Sayı 4, 331-339, 2005.
[17] Durman, M., Murphy, S., “An electron metallographic study of pressure die-cast commercial zinc–aluminum-based alloy ZA27,” Journal of Materials Science, 32, 1603-1611.