Comparison of Gamma Sources (Cobalt and Cesium) for Density Measurement of Metals and Alloys via Using Transmission Technique
Comparison of Gamma Sources (Cobalt and Cesium) for Density Measurement of Metals and Alloys via Using Transmission Technique
One of the solutions for density measurement is to make use of gamma-ray transmission technique. We studied by this technique, using by Co-60 and Cs-137. Each source, without materials in geometry, was counted and noted intensities as (I0). All materials were counted and noted intensities as (I). [I/I0] rates were calculated. Now, density of materials could be determined via using Beer-Lambert Equation. Experimental application was performed on industrial metals or metal alloys like lead&copper and steel&brass. Given densities and obtained densities were compared. Differences or deviations for lead, stell copper and brass are -5.07; 0.26; 1.11; -5.73 (Co-60) and 1.07; 3.08; -0.22; 2.34 (Cs-137) consequently. It could be said that, these differences are still in acceptable limits.
Keywords:
Co-60/Cs-137, metal/alloy, Co-60/Cs-137, density measurement, metal/alloy, gamma-transmission technique, nuclear applications nuclear technique,
___
- [1] Mix, P.E., “Introduction to non-destructive testing”, John Wiley, New York, (1987).
- [2] Turgay, M.E., “Density assessment of different metals and alloys by gamma-ray transmission technique via using Co-60 radioactive source”, Journal of Physical Science and Application 7(1) (2017) : 39–42.
- [3] Földiak, G., “Industrial application of radioisotopes”, Institute of Isotopes of the Hungarian Academy of Sciences, Budapest, (1986).
- [4] Buyuk, B., “Gamma attenuation behavior of some stainless and boron steels”, Acta Physica Polonica A 127(4) (2015) : 1342-1345.
- [5] Buyuk, B., Tugrul, A.B., “An investigation on gamma attenuation behaviour of titanium diboride reinforced boron carbide–silicon carbide composites”, Radiation Physics and Chemistry 97 (2014) : 354-359.
- [6] Moreira, A.C., Appoloni, C.R., Fernandes, C.P., “Gamma ray transmission technique applied to porous phase characterization of low-porosity ceramic samples”, Materials and structures 46(4) (2013) : 629-637.
- [7] Karagoz, B., et al. “Determination of Gamma Transmittance and Density Assessment for Al Doped ZnO Thin Films by Using Gamma Transmission Technique”, Defect and Diffusion Forum 312–315 (2011) : 830–835, https://doi.org/10.4028/www.scientific.net/ddf.312-315.830.
- [8] Bjoernstad, T., Stamatakis, E., “Scaling studies with gamma transmission technique”, Conference: Oil Field Chemistry, At: Geilo, Norway, (2006).
- [9] Course Notes, Radiation Detectors, Chapter 18, Oregon State University.
- [10] Gardner, R.P., Ely, R.L., “Radioisotopes Measurement Applications in Engineering”, Reinhold Publishing Co., New York, (1967).
- [11] Bilge, A.N., Tuğrul, A.B., “Bases of Industrial Radiography”, I.T.U. Publishing, Istanbul, (1990).
- [12] Turgay, M.E., “Density measurement for different metals by gamma-ray transmission technique used by radioactive isotopes”, M.Sc. Thesis, Istanbul Technical University, Istanbul, (2005).
- Yayın Aralığı: Yılda 3 Sayı
- Başlangıç: 2016
- Yayıncı: Muhammet Kurulay