Prediction of Deformation Mode of Bi-Metallic Rod Extrusion through Arbitrarily Curved Dies

The modes of deformation of bi-metal rods during forward extrusion through arbitrarily curved dies are studied in this paper. An analytical solution is developed to predict the mode of deformation by using the upper bound method. The effects of the yield stress ratio, shape and length of the die, extrusion ratio and frictional shear factors at the interface and the die surface are considered in the analysis. It is found that frictional shear factor at the interface, the ratio of flow stresses and die length are important parameters that can change mode of deformation from uniform deformation to cladding-type. Shape of the die, reduction in area and frictional shear factor at the die surface have not effect on the mode of deformation, although the effects are great on the extrusion pressure. The extrusion process is also simulated by using the finite element code, ABAQUS. The theoretical results show good agreement with the FEM results.

Keywords:

FEM, Bi-metallic rod Extrusion, Deformation mode,

PDF

___

Osakada K., Limb M., Mellor P.B., “Hydrostatic extrusion of composite rods with hard cores”, International Journal of Mechanical Sciences 15 291-307(1973).
Ahmed N., “Extrusion of copper clad aluminum of wire”, Technology, 2:19–32(1978). Mechanical Working
Avitzur B. Handbook of Metal-Forming Processes, New York: Wiley,(1983).
Tokuno H., Ikeda K., “Analysis of deformation in extrusion of composite rods”, Journal of Materials Processing Technology26:323-335(1991).
Yang D.Y., Kim Y.G., Lee C.M., “An upper-bound solution for axisymetric extrusion of composite rods through curved dies”, International Journal of Mechanical Sciences31:565-575(1991).
Sliwa R., “Plastic zones in the extrusion of metal composites”, Journal of Materials Processing Technology67:29-35(1997).
Kazanowski P., Epler M.E., Misiolek W.Z., “Bi- extrusion-process
optimization”, Materials Science and Engineering
A 369:170–180 (2004). and product
Nowotynska I., Smykla A. “Influence of die geometric parameters on plastic flow of layer composites during extrusion process”, Journal of Materials Processing Technology209 1943- 1949(2009).
Chitkara N.R.,Aleem A., “Extrusion of axi- symmetricbi-metallictubes: someexperimentsusinghollowbilletsandtheapplicatio n of a generalizedslabmethod of analysis”, International Journal of MechanicalSciences 43 2857–2882(2001).
Chitkara N.R.,Aleem A., “Extrusion of axi- symmetricbi
metallictubesfromsolidcircularbillets: application of
boundanalysisandsomeexperiments”, International
MechanicalSciences43:2833–2856(2001). of
Hwang Y.M., Hwang T.F., “An investigation into the plastic deformation behaviour within a conical die during composite rod extrusion”, Journal of Materials 233(2002). Technology 121:226
Khosravifard A., Ebrahimi R., “Investigation of parameters affecting interface strength in Al/Cu clad bimetal rod extrusion process”, Materials and Design 31 493-499(2010).
Gordon W.A., Van Tyne C.J., Moon Y.H., “Axisymmetric extrusion through adaptable dies— part 1: flexible velocity fields and power terms”, International Journal of Mechanical Sciences 49 86–95(2007).
Yang D.Y., Han C.H., “A new formulation of generalized velocity field for axi-symmetric forward extrusion Transactions Engineering for Industry 109:161–168(1987). Journal of of ASME”,
Gordon W.A., Van Tyne C.J., Moon Y.H., “Axisymmetric extrusion through adaptable dies— part 3: minimum pressure streamlined die shapes”, International Journal of Mechanical Sciences 49 104-115(2007).

Gazi University Journal of Science-Cover

Yayın Aralığı: Yılda 4 Sayı
Başlangıç: 1988
Yayıncı: Gazi Üniversitesi, Fen Bilimleri Enstitüsü

Arşiv