___

• Guesser, W; Schroeder, T. and Dawson, S.
• “Production Experience with compacted graphite
• iron automotive components”, AFS
• Transactions, Desplaines, 2001.
• Abele E, Schramm B. "Wear behavior of PCD in
• machining",Proceedings of the 2nd industrial
• diamond conference, Rome, 2007
• M. Heck, H. M. Ortner, S. Flege, U. Reuter, W.
• Ensinger, “Analytical investigations concerning
• the wear behaviour of cutting tools used for the
• machining of compacted graphite iron and grey
• cast iron”, International Journal of Refractory
• Metals & Hard Materials 26 197–206, 2008
• Şeker, U., Kurt, A. and Çiftçi, İ., “Design and
• construction of a dynamometer for measurement
• of cutting forces during machining with linear
• motion”, Materials and Design, 23: 355-360,
• -
• Günay, M., “Talaş kaldırma işlemlerinde kesici
• takım talaş açısının kesme kuvvetlerine
• etkisinin deneysel olarak incelenmesi”, Yüksek
• Lisans Tezi, Gazi Üniversitesi Fen Bilimleri
• Enstitüsü, Ankara, 40-49 2003.
• Demir, H. ve Güllü, A.,“Taşlama
• parametrelerinin taşlama kalitesine etkilerinin
• incelenmesi”, Pamukkale Üniversitesi
• Mühendislik Fakültesi Mühendislik Bilimleri
• Dergisi, Cilt 7, 189-198, 2001.
• Demir H., Güllü A., Şeker U., “Düzlem Taşlama
• İşleminde Taşlama Kuvvetlerinin Ölçülmesi İçin
• Bir Dinamometre Tasarımı ve İmalatı”,
• Teknoloji-ZKÜ Karabük Teknik Eğitim
• Fakültesi Dergisi, Cilt 9, Sayı 2, 111-118, 2006.
• Sadık, I. “The Interaction between Cutting Data
• and Tool Performance for different CuttingTool
• Material in Milling of Compacted Graphite Iron”
• Sixth International Conference on High
• SpeedMachining, 2007.
• Georgiou G.,“CGI high speed machine tool
• solutions”, Compacted graphite iron
• machining workshop Conference,Warren,
• USA, Lamb Technician, 2002.
• BerglundA.,et al., “Analysis of compacted
• graphite iron machining by investigation of tool
• temperature and cutting force”, 1st International
• Conference on Process Machine Interactions,
• Hannover Germany, 2008.
• Jönsson H., “Milling of Compacted Graphite
• Iron”, Royal Institute of Technology, Production
• Engineering, Stockholm, Sweden,2008.
• Berglund A. and Nicolescu C. M. “Investigation
• of the effect of microstructure on CGI
• machining”, Swedish Production Symposium,
• Gothenburg, Sweden, 2007.
• Richetti, et al., 2004). Richetti A., “Influence of
• the number of inserts for tool life evaluation in
• face milling of steels”, International Journal of
• Machine Tools &Manufacture, vol. 44, 695-
• , 2004.
• Kurt, A., “Talaş Kaldırma Sırasında Oluşan
• Kesme Kuvvetleri ve Mekanik Gerilmelerin
• Deneysel Olarak İncelenmesi ve Matematiksel
• Modellerinin Oluşturulması”, Doktora Tezi,
• Gazi Üniversitesi Fen Bilimleri Enstitüsü,
• Ankara, 115-215, 2006.
• Mavi A., Korkut, İ., “Vermiküler Grafitli Dökme
• Demirin İşlenebilirliğinin Deneysel Olarak
• Araştırılması”, 5. Uluslararası İleri
• Teknolojiler Sempozyumu (IATS’09), 13-15
• Mayıs 2009, Karabük, Türkiye
• Çiftçi, İ., “The influence of cutting tool coating
• and cutting speed on Cutting forces and surface
• roughness in machining of Austenitic stainless
• steels”, Journal of the Faculty of Engineering
• and Architecture of Gazi University, 20, 205-
• , 2005.
• Sandvik, C., Metal İşleme Ürünleri Tornalama
• Takımları Katoloğu, Sandvik Coromant,
• İstanbul, 1-8 2002.
• Haber, R. E., Alique, A., “Intelligent process
• supervision for predicting tool wear in machining
• processes”, Mechatronics, vol. 13, 825-849,
• -
• Özel, T. N., “Prediction of flank wear by using
• back propagation neural network modeling when
• cutting hardened H-13 steel with chamfered and
• honed CBN tools”, International Journal of
• Machine Tools & Manufacture, vol. 42, 287-
• , 2002.
• Lee, H., “One-step-ahead prediction of Flank
• wear using cutting force”, International Journal
• of Machine Tools & Manufacture, vol. 39,
• -1760, 1999.