Dokuma Cam Elyaf Takviyeli Polimer Kompozitlerin Tabaka Diziliminin ve Genişliklerinin SERR Üzerindeki Etkileri
Bu çalışmada, Mod I çatlak ilerlemesi altında dokuma cam elyaf takviyeli polimer (GFRP) kompozitlerinin kırılma davranışı deneysel olarak araştırılmış ve tabaka diziliminin ve numune genişliklerinin delaminasyon direncine olan etkilerini belirlemek için sayısal olarak modellenmiştir. Açığa çıkan şekil değiştirme enerjisinin (SERR) hesaplanması için farklı yöntemler kullanılmıştır: deneysel çözüm için, deneysel uyum kalibrasyon yöntemi (CCM), modifiye edilmiş kiriş teorisi (MBT), modifiye uyum kalibrasyon yöntemi (MCC) kullanılmıştır ve sayısal çözüm için sanal çatlak kapatma tekniği (VCCT) kullanılmıştır. DCB test numuneleri, SERR değerlerini elde etmek için kullanılmıştır. Delaminasyon, çatlak analizi ve Mod I SERR değerilerinin VCCT tarafından hesaplanması için üç boyutlu sonlu eleman modeli kullanılmıştır. Deneysel ve sayısal sonuçların birbiriyle uyumlu olduğu ve böylece bir dokuma cam elyaf takviyeli polimer kompozitlerin SERR değerini analiz etmek için VCCT metodunun uygun bir yöntem olduğu görülmüştür.
Effects of Lay-Up Sequence and Widths on The SERR of Woven Glass Fiber Reinforced Polymer Composites
In this paper, fracture behavior of woven Glass Fiber Reinforced Polymer (GFRP) composites underMode I crack growth was experimentally investigated and numerically modeled, to determine theeffects of lay-up sequence and widths on delamination resistance. Different methods are used forcalculation of strain energy release rate (SERR): for the experimental solution, experimentalcompliance calibration method (CCM), modified beam theory (MBT), modified compliance calibration(MCC) are used and virtual crack closure technique (VCCT) are used for the numerical solution. Toachieve this aim DCB (double cantilever beam) test specimens are used to evaluate the SERR values.Three-dimensional finite element model is used to perform the delamination, crack analysis, andMode I SERR value is calculated by the VCCT. It is seen that there is an agreement betweenexperimental and numerical results so that the VCCT method is to be an appropriate method foranalyzing a SERR value of woven glass fiber reinforced polymer composites.
___
- Hyer M.W.: Stress analysis of fiber-reinforced
composite materials. McGraw-Hill, Massachusetts, (1998).
- Broek D.: Elementary Engineering Fracture Mechanics.
Kluwer Academic Publishers, Boston, Massachusetts,
(1996).
- O'Brien T.K.: Fracture Mechanics of Composite
Delamination. Composites: ASM International, 21, 241-
245 (2001).
- O'Brien, T. K.: Characterization of delamination onset
and growth in a composite laminate. Damage in composite
materials, ASTM STP 775/2, 140-167 (1982).
- Tay T. E.: Characterization and analysis of delamination
fracture in composites: an overview of developments from
1990 to 2001, Applied Mechanics Reviews 56/1, 1-32
(2003). DOI:10.1115/1.1504848
- De Morais A.B., De Moura M.F., Marques A.T., De Castro
P.T.: Mode-I interlaminar fracture of carbon/epoxy crossply composites. Composites Science and Technology, 62/5,
679-686 (2002). DOI:10.1016/S0266-3538(01)00223-8
- Toygar M.E., Toparli M., Uyulgan B.: An investigation of
fracture toughness of carbon/epoxy composites. Journal of
reinforced plastics and composites, 25.18, 1887-1895
(2006). DOI: 10.1177/0731684406069916
- Aliyu A.A., Daniel I.M.: Effects of strain rate on
delamination fracture toughness of graphite/epoxy.
Delamination and debonding of materials, ASTM STP, 876,
336-348 (1985).
- Chai H.: The characterization of Mode I delamination
failure in non-woven, multidirectional laminates.
Composites, 15, 277–90 (1984).
- Choi NS, Kinloch AJ, Williams JG.: Delamination
fracture of multidirectional carbon-fiber/epoxy
composites under Mode I, Mode II and mixed-Mode I/II
Loading. J Compos Mater, 33, 73–100 (1999).
- Canturri C, Greenhalgh ES, Pinho ST, Ankersen J.:
Delamination growth directionality and the subsequent
migration processes – the key to damage tolerant design.
Compos Part A Appl Sci Manuf, 54, 79–87 (2013).
- Pelegri AA, Tekkam A.: Optimization of laminates’
fracture toughness using design of experiments and
response surface. J Compos Mater, 37, 579–96 (2003).
- Pereira AB, de Morais AB.: Mode I interlaminar
fracture of carbon/epoxy multidirectional laminates.
Compos Sci Technol, 64, 2261–70 (2004).
- Sebaey TA, Blanco N, Costa J, Lopes CS.:
Characterization of crack propagation in mode I
delamination of multidirectional CFRP laminates. Compos
Sci Technol, 72, 1251–6 (2012).
- Chou I, Kimpara I, Kageyama K, Ohsawa I.: Mode I and
Mode II Fracture Toughness Measured Between
Differently Oriented Plies in Graphite/Epoxy Composites.
Compos Mater Fatigue Fract – Fifth Vol ASTM STP 1230,
Martin RH, editor. Am Soc Test Mater Philadelphia, 132–
51 (1995).
- Shokrieh MM, Heidari-Rarani M.: Effect of stacking
sequence on R-curve behavior of glass/epoxy DCB
laminates with 0//0 crack interface. Mater Sci Eng, A, 529,
265–9 (2011).
- Davidson B.D., Krüger R., König M.: Effect of stacking
sequence on energy release rate distributions in
multidirectional DCB and ENF specimens. Engineering
Fracture Mechanics, 55/4, 557-569 (1996).
- Hudson R.C., Davidson B.D., Polaha J.J.: Effect of
remote ply orientation on the perceived mode I and mode
II toughness of h/h and h/h interfaces, Appl. Compos.
Mater. 5, 123–138 (1998).
- Polaha J.J., Davidson B.D., Hudson R.C., A.: Pieracci,
Effects of mode ratio, ply orientation and precracking on
the delamination toughness of a laminated composite, J.
Reinf. Plast. Compos. 15, 141–173 (1996).
- Schön J., Nyman T., Blom A., Ansell H.: A numerical and
experimental investigation of delamination behaviour in the DCB
specimen, Compos. Sci. Technol. 60, 173–184 (2000).
- ASTM D 5528-13.: Standard test method for mod 1
interlaminar fracture toughness of unidirectional fiberreinforced polymer matrix composites. ASTM Annuof
Standards, West Conshohocken, PA, USA, 2013.
- ASTM D3039 / D3039M-17, Standard test method for
tensile properties of polymer matrix composite materials,
ASTM International, West Conshohocken, PA, USA, 2017.
- ASTM D3518-D3518M-13.: Standard test method for
in-plane shear response of polymer matrix composite
materials by tensile test of a ±45 degree Laminate. ASTM
Annual Book of Standards, West Conshohocken, PA, USA,
2001.
- Rybicki E.F., Kanninen M.F.: Finite element calculation
of stress intensity factors by a modified crack closure
integral, Engineering Fracture Mechanics. 9, 931–938
(1977). DOI:10.1016/0013-7944(77)90013-3
- Shen F., Lee K.H., Tay, T.E.: Modeling delamination
growth in laminated composites. Composites Science and
Technology, 61(9), 1239-1251 (2001).
- Krueger R.: Virtual crack closure technique: history,
approach and applications. Applied Mechanics Reviews,
57 (2), 109–143 (2004). DOI:10.1115/1.1595677
- Research, A.A.: Release 15.0, Help System. In. ANSYS
Structural Analysis Guide. ANSYS, Inc, (2015)