Taguchi Metodu ile Kalsiyum Karpit Cürufundan Kalıplama ve Kalsinasyon Yöntemleri Uygulanarak Kalsiyum Oksit Briketlerinin Hazırlanması
Asetilen gazı üretimi sırasında elde edilen kalsiyum karpit cürufunun (KKC) depolanması çevre açısından sorun yaratması nedeniyle, bu çalışmada KKC’den üretilen kalsiyum oksit (CaO) briketlerinin tekrar kalsiyum karpit (CaC2) üretiminde kullanılması amaçlanmıştır. Taguchi yaklaşımı ile bağlayıcı tipinin (fosforik asit (H3PO4), melas ve mısır şurubu), bağlayıcı miktarının (%1, %3 ve %5), briketleme basıncının (20, 28 ve 36 MPa), kalsinasyon sıcaklığının (800, 900 ve 1000 oC) ve kalsinasyon süresinin (30, 45 ve 60 dk) üretilen CaO briketlerinin dayanımına olan etkileri araştırılmıştır. En yüksek dayanım değeri 4,05 MPa olarak bulunmuştur. En yüksek dayanıma sahip briketin dayanıklık ve kırılganlık değerleri sırasıyla %92 ve %8 olarak belirlenmiştir. ANOVA analizine göre, üretim parametrelerinin CaO dayanımına olan etkisi sırasıyla (i) bağlayıcı miktarı, (ii) bağlayıcı tipi, (iii) briketleme basıncı, (iv) kalsinasyon sıcaklığı ve (v) kalsinasyon süresi olarak belirlenmiştir. Elde edilen optimum deney şartları ise; %5 bağlayıcı miktarı, 28 MPa briketleme basıncı, 900 oC kalsinasyon sıcaklığı ve 60 dakika kalsinasyon süresi olarak belirlenmiştir. Elde edilen CaO briketleri CaC2 üretiminde tekrar kullanılabilecek dayanımı değerini sağlamaktadır.
Study of using Calcium Carbide Slag to Prepare Calcium Oxide Briquettes by Molding and Calcination Processes through Taguchi Method
As the disposal of calcium carbide slag (CCS) obtained a by-product during an acetylene gas processcreates an environmental problem, this study aimed to use of CCS to prepare calcium oxide (CaO)briquettes for re-use in the production of calcium carbide (CaC2). The influence of binder types(phosphoric acid (H3PO4), molasses, and corn syrup), binder amount (1, 3, and 5%), briquetting pressure(20, 28, and 36 MPa), calcination temperature (800, 900, and 1000 oC), and calcination time (30, 45, and60 min) on the strength value of CaO briquettes was investigated using the Taguchi approach. The highestcompressive strength value of CaO briquettes was found to be 4.05 MPa. The stability and friabilityvalues of the final product were 92% and 8%, respectively. ANOVA analysis revealed that thecontribution rate of production parameters on the strength value of CaO briquettes were as follows: (i)binder amount, (ii) binder type, (iii) briquetting pressure, (iv) calcination temperature, and (v) calcinationtime. The optimal production conditions were determined as follows: the amount of binder: 5%,briquetting pressure: 28 MPa, calcination temperature: 900 oC, and calcination time: 60 min. The obtainedCaO briquettes provide a required strength value for re-use in the production of CaC2.
___
- Düzyol S., 2016. Taguchi Deneysel Tasarım
Metodu Kullanılarak Karadon (Zonguldak)
Kömürünün Yağ Aglomerasyonu Davranışının
İncelenmesi, Çukurova Üniversitesi
Mühendislik Mimarlık Fakültesi Dergisi, 31(2),
77-84, (in Turkish).
- ASTM D440–86, 2002. Standard Test Method
of Drop Shatter Test for Coal, ASTM
International, West Conshohoken, PA, USA.
- Zhong, Q., Yang, Y., Li, Q., Xu, B., Jiang, T.,
2017. Coal Tar Pitch and Molasses Blended
Binder for Production of Formed Coal
Briquettes from High Volatile Coal, Fuel
Processing Technology, 157, 12-19.
- Zhang, S., Gong, X., Wang, Z., Cao, J., Guo,
Z., 2014. Preparation of Block CaO from
Carbide Slag and Its Compressive Strength
Improved by H3PO4, International Journal of
Mineral Processing, 129, 6-11.
- Bo, W., Huilan, S., Shiwen, B., 2010. Effect of
Carbide Slag on High Pressure Digestion
Properties of Diaspore. Light Metals, TMS
(The Minerals, Metals & Materials Society)
Edited by John. A. Johnson.
- Li, Y., Liu, H., Sun, R., Wu, S., Lu, C., 2012.
Thermal Analysis of Cyclic Carbonation
Behavior of CaO Derived from Carbide Slag at
High Temperature. Journal of Thermal
Analysis and Calorimetry, 110, 685-694.
- Li, Y., Sun, R., Liu, C., Liu, H., Lu, C., 2012.
CO2 Capture by Carbide Slag from ChlorAlkali
Plant in Calcination/Carbonation
Cycles. International Journal of Greenhouse
Gas Control, 9, 117-123.
- Tan, Y., Li, T, Zeng, G. M., 2005. Promotion
Effect of Additives on Sulfur Capture during
Coal Combustion with Carbide Slag. Journal of
Fuel Chemistry and Technology, 33 767-770.
- Cao, J.X., Liu, F., Lin, Q., Zhang, Y., Dong,
Y.G., Zeng, L.K., 2008. Effect of Calcination
Temperature on Mineral Composition of
Carbide Slag, Lime Activity and Synthesized
Xonotlite. Key Engineering Materials, Trans
Tech Publ, 1545-1547.
- Liu, F., Wang, X., Cao, J., 2012. Effect of
Ultrasonic Process on Carbide Slag Activity
and Synthesized Xonotlite. Physics Procedia,
25, 56-62.
- Cao, J., Liu, F., Lin, Q., Zhang, Y., 2008.
Hydrothermal Synthesis of Xonotlite from
Carbide Slag. Progress in Natural Science,
18,1147-1153.
- Liu, X., Zhu, B., Zhou, W., Hu, S., Chen, D.,
Griffy-Brown, C., 2011. CO2 Emissions in
Calcium Carbide Industry: an Analysis of
China's Mitigation Potential. International
Journal of Greenhouse Gas Control, 5,
1240-1249.
- Namarak, C., Satching, P., Tangchirapat, W.,
Jaturapitakkul, C., 2017. Improving the
Compressive Strength of Mortar from a Binder
of Fly Ash-Calcium Carbide Residue.
Construction and Building Materials, 147,
713-719.
- Horpibulsuk, S., Munsrakest, V., Udomchai,
A., Chinkulkijniwat, A., Arulrajah, A., 2014.
Strength of Sustainable Non-Bearing Masonry
Units Manufactured from Calcium Carbide
Residue and Fly Ash. Construction and
Building Materials, 71, 210-215.
- Phetchuay, C., Horpibulsuk, S.,
Suksiripattanapong, C., Chinkulkijniwat, A.,
Arulrajah, A., Disfani, M.M., 2014. Calcium
Carbide Residue: Alkaline Activator for Clay–
Fly Ash Geopolymer. Construction and
Building Materials, 69, 285-294.
- Krammart, P., Tangtermsirikul, S., 2004.
Properties of Cement Made by Partially
Replacing Cement Raw Materials with
Municipal Solid Waste Ashes and Calcium
Carbide Waste. Construction and Building
Materials, 18, 579-583.
- Horpibulsuk, S., Phetchuay, C.,
Chinkulkijniwat, A., 2011. Soil Stabilization
by Calcium Carbide Residue and Fly Ash.
Journal of Materials in Civil Engineering, 24,
184-193.
- Kılıç, Ö., 2013. Impact of Physical Properties
and Chemical Composition of Limestone on
Decomposition Activation Energy. Asian
Journal of Chemistry, 25 (14), 8116-8120.
- Kılıç, Ö., Anıl, M., 2005. Farklı Kalsinasyon
Ortamlarının Kireç Üretimi Üzerindeki
Etkilerinin Araştırılması, Madencilik, 44(4),
19-28, (in Turkish).