Esra AKGÜL, Hüseyin Gazi TÜRKSOY, Emel KIZILKAYA AYDOĞAN, Diyar AKAY

MOORA-BASED TAGUCHI OPTIMIZATION FOR SELECTION OF MURATA VORTEX SPINNER MACHINE PARAMETERS

Murata Vortex Eğirme (MVS) en umut verici yeni nesil hava jetli eğirme teknolojilerinden biri olarak kabul edilmektedir. Nihai iplik özelliklerini etkileyen optimum MVS makine parametresi seçimi tekstil sektöründe zor ve karmaşık bir görevdir. Bu çalışmada, MVS pamuk ipliği için, mümkün olan alternatifler arasından optimum düze basıncı ve üretim hızını seçmek için Multi-Objective Optimization on the Basis of Ratio Analysis (MOORA) tabanlı Taguchi yaklaşımı önerilmiştir. Bu parametrelerin performansları, bu method kullanılarak eğrilmiş MVS ipliklerinin yedi kalite karakteristiğine dayandırılarak değerlendirilmiştir

MURATA VORTEKS EĞİRME MAKİNESİ PARAMETRELERİNİN SEÇİMİ İÇİN MOORA TABANLI TAGUCHI OPTIMIZASYONU

Murata Vortex Spinner (MVS) is accepted as one of the most promising new generation air jet spinning technology. Selection of optimum MVS machine parameter which affects properties of the final yarn is difficult and complex task in textile industry. This study proposes the Multi-Objective Optimization on the Basis of Ratio Analysis (MOORA) - based Taguchi approach to select optimum nozzle pressure and delivery speed among available alternatives for cotton MVS yarn. The performances of these parameters are evaluated based on seven quality characteristics of MVS spun yarn using this method

PDF

___

1. Murata vortex spinner. Retrieved May 2, 2015 from http://www.muratec-vortex.com
2. Lawrence, C., 2010, ‘Advantage is Yarn Spinning Technology’, Woodhead Publishing Limited, September, (pp:464).
3. Erdumlu, N., Ozipek, B., Oztuna, A.S., Cetinkaya, S., 2009, ‘’Investigation of Vortex Spun Yarn Properties in Comparison with Conventional Ring and Openend Rotor Spun Yarns’’, Textile Research Journal, 79, (585-595).
4. Erdumlu, N., Ozipek, B., 2010, ‘Effect Of The Draft Ratio On The Properties Of Vortex Spun Yarn’, Fibres&Textiles In Eastern Europa, 3(80), 38-42.
5. Murata Vortex Spinner (MVS) No.851 Instructional manuel. Osaka Japan: Muratec , Murata Machinery Ltd.
6. Ortlek, H.G., Ulku, S., 2005, ‘Effect of some variables on properties of 100% cotton vortex spun yarn’, Textile Research Journal, 75(6), (458–461).
7. Ortlek, H.G., Ulku, Ş., 2007, ‘Effect of spandex and yarn counts on the properties of elastic core-spun yarns produced on murata vortex spinner’, Textile Research Journal, 77, (432-436).
8. Tyagi, G.K., Sharma, D., 2004, ‘Performance and low-stress characteristics of polyester-cotton MVS yarns’, Indian J Fibre Textile Res, 29, (301–307).
9. Basal, G., Oxenham, W., 2006, ‘Effects of some process parameters on the structure and properties of vortex spun yarn’, Textile Research Journal, 76(6), (492–499).
10. Erdumlu N., Ozipek, B., Oxenham, W., 2012, ‘The Structure And Properties Of Carded Cotton Vortex Yarns’, Textile Research Journal, 82(7), (708–718).
11. Erdumlu, N, Ozipek, B., Oxenham W., 2012, ‘Vortex spinning technology’, Textile Progress, 44(3-4), (141-174).
12. Yang, W. H., Tarng, Y. S., 1998, “Design Optimization of Cutting Parameters for Turning Operations Based on the Taguchi Method.” Journal of Materials Processing Technology, 84, (122–129).
13. Park, C.K., Ha, J., 2005, ‘A Process For Optimizing Sewing Conditions To Minimize Seam Pucker Using The Taguchi Method’, Textile Research Journal, 75(3), (245-252).
14. Kuo, C.F.J., Su, T.l., T., C.P., 2007, ‘Optimization Of The Needle Punching Process For The Nonwoven Fabrics With Multiple Quality Characteristics By Grey-Based Taguchi Method’, Fiber And Polymers, 6(8), (654-664).
15. Kumar, S., Satsangi, P. S., Prajapati, D.R., 2011, “Optimization of Green Sand Casting Process Parameters of a Foundry by Using Taguchi’s Method.” The International Journal of Advanced Manufacturing Technology, 55, (23–34).
16. Tansel, I. N., Gülmez, S., Demetgul, M., Aykut, S., 2011, “Taguchi Method–Gonns Integration: Complete Procedure Covering from Experimental Design to Complex Optimization.” Expert Systems with Applications, 38, (4780–4789).
17. Tong, L. I., Chen, C. C., Wang, C. H., 2007, “Optimization of Multi-Response Processes Using the Vikor Method.” The International Journal of Advanced Manufacturing Technology, 31: 1049–1057.
18. Kuo, Y., Yang, T., Huang, G. W., 2005, “The Use of a Grey-Based Taguchi Method for Optimizing Multi-Response Simulation Problems.” Engineering Optimization, 40 (6), (517–528).
19. Yang, T., Chou, P., 2005, “Solving a Multiresponse Simulation-Optimization Problem with Discrete Variables Using a Multiple Attribute Decision-Making Method.” Mathematics and Computers in Simulation, 68: 9–21.
20. Lu, J.-C., Yang, T., Su, C.T., 2012, “Analysing Optimum Push/Pull Junction Point Location using Multiple Criteria Decision Making for Multistage Stochastic Production System.” International Journal of Production Research, 50 (19):(5523–5537).
21. Simsek, B., Ic, Y.T., Simsek, E.H., 2013, ‘A TOPSIS based taguchi optimization to determine optimal mixture proportions of the high strength selfcompacting concrete’, Chemometrics and intelligent Laboratory Systems, 125, (18-32).
22. Iç, Y. T., and S. Yıldırım, 2013, “MOORA –based Taguchi Optimization For İmproving Product Or Process Quality.” International Journal Of Production Research, 11(51), (3321-3341).
23. Sarpkaya, Ç., Özgür, E., Sabır E. C., 2015, “The Optimization of Woven Fabric Tensile Strength with Taguchi Method Based on Grey Relational Analysis”, Tekstil ve Konfeksiyon, 4(25), (293-299).
24. Majumdar, A., Sarkar, B., & Majumdar, P., 2006, ‘A new algorithm of cotton fiber selection and lay-down using TOPSIS method of multi-criteria decision making’, Indian Journal of Fibers & Textile Research, 31, (248–255).
25. Majumdar, A., Kaplan, S., Göktepe, Ö., 2010, ‘Navel selection for rotor spinning denim fabrics using a multi-criteria decision-making process’, The Journal of The Textile Institute, 101(4), (304-309).
26. Valipour, P., Moghassem A.R., 2014, ‘Employment of PROMETHEE Approach for Selecting Suitable Yarn for Weft Knitting Process Considering Drawing Frame Varibles’, Fibres and Polymers, 4(15), (865-873).
27. Kaplan, S., Araz, C., Goktepe, O., 2006, ‘A multi-criteria decision aid approach on novel selection problem for rotor spinning’, Textile Research Journal, 76, (896–904).
28. Taguchi, G., 1986, ‘Introduction to quality engineering: designing quality into products and processe’, Asian Productivity Organizasion, Tokyo, (97-108).
29. Taguchi G., Chowdhury S., Wu, Y., 2004, Taguchi’s quality engineering handbook, Hoboken, NJ: John Wiley, (p.1662).
30. Ogulata, R.T., Mezarcioz, S.M., 2011, “Optimization Of Air Permeability Of Knitted Fabrics With The Taguchi Approach”, The Journal Of The Textile Institute, 102(5), (395-404).
31. Naveen, S.A., Aravindan , S., and Noorul Haq, A., 2009, “Influence Of Machining Parameters On Surface Roughness Of GFRP Pipes”, Advances In Production Engineering& Management Journal, 4(1-2), (47-58)
32. Brauers, W. K. M., 2004, “Optimization methods for a stakeholder society. A revolution in economic thinking, by multiobjective optimization: Nonconvex Optimization and its Applications”, Kluwer Academic Publishers, Boston, U.S.A.
33. Brauers, W. K. M., E. K. Zavadskas, Z. Turskis, and T. Vilutiene, 2008, “Multi Objective Contractor’s Ranking by Applying the Moora Method”, Journal of Business Economics and Management, 9 (4), (245–255).
34. Brauers W.K.M, Zavadskas E.K, 2009, ‘’Robustness of the multiobjective MOORA method with a test for the facilities sector’’ Technological and Economic Development of Economy: Baltic Journal on Sustainability, 15, (352–375).
35. Chakraborty, S., 2011, “Applications of the MOORA method for decision making in manufacturing environment”, The International Journal of Advanced Manufacturing Technology, 54, (1155–1166).