Soğutucular için Optimum Yalıtım Kalınlığı Dağılımının Belirlenmesi
Üretilen elektrik enerjisinin büyük bir kısmı ya ticari ya da ev tipi soğutma sistemlerinde tüketilmektedir. Dış hacim genelde belli olduğundan, bir soğutma sisteminin iç hacmi belirli bir enerji tüketimi değeri için önemlidir. Dolayısıyla, bir buzdolabının çalışma ve durma zamanında değişen iç ve dış şartlara göre yalıtım malzemesinin optimum dağılımı oldukça önemlidir. İzolasyon malzemesinin üniform dağılımı, tüm yüzeyler için sadece konveksiyon ve iletim dirençlerinin ve aynı zamanda buzdolabının çalışma ve durma periyotları için aynı değerde olması durumunda kullanılabilir. Bu çalışmada, soğutma sistemleri için belirli bir yalıtım malzemesi hacmi veya iç hacim için ısı yalıtım malzemesinin optimum dağılımının genel bir çözümü önerilmiş ve ayrıca bir örnek çalışma ile açıklanmıştır.
Determination of Optimum Insulation Thickness Distribution for Refrigerators
Most of electricity is consumed in either commercial or domesticrefrigeration systems. Since the outer volume is determined, inner volume of arefrigeration system is important for a specified energy consumption. Therefore,the optimum distribution of insulation material according to inside and outsideconditions for on and off time of a refrigerator is very important. Uniformdistribution of insulation material is useful only convection and conductionresistances are the same for all sides and also on and off periods. In this study, ageneral solution of the optimum distribution of thermal insulation material for agiven insulation material volume or given inner volume is suggested forrefrigeration systems and also explained by a case study.
___
- [1] Christensen, L. B. 1981. The insulation of
freezers and refrigerators - how thick it should
be? International Journal of Refrigeration, 4
(1981), 73-76.
- [2] Dimitriyev, V. I., 1984. Optimum insulation
thicknesses for domestic refrigerators and
freezers. International Journal of Refrigeration,
7(1984), 72-73.
- [3] Lee,T., Lee, W., Lee, Y., 2006. Optimization of the
Insulation Wall Thickness of Refrigerator.
International Refrigeration and Air Conditioning
Conference, Paper 837.
- [4] Yoon, W., Seo, K., Kim, Y., 2013. Development of
an optimization strategy for insulation thickness
of a domestic refrigerator-freezer. International
Journal of Refrigeration, 36(2013), 1162–1172.
- [5] Söylemez, M., Ünsal, M., 1999. Optimum
insulation thickness for refrigeration applications, Energy Conversion and
Management, 40(1999), 13-21.
- [6] Daouas, N., Hassen, Z., Aissia, H. B., 2010.
Analytical periodic solution for the study of
thermal performance and optimum insulation
thickness of building walls in Tunisia. Applied
Thermal Engineering, 30(2010), 319-326.
- [7] Kaynakli, O., 2011. Parametric investigation of
optimum thermal insulation thickness for
external walls, Energies, 4(2011), 913-927.
- [8] Özel, M., Pihtili, K., 2007. Optimum location and
distribution of insulation layers on building
walls with various orientations. Building and
Environment, 42(2007), 3051-3059.
- [9] Al-Sanea, S. A., Zedan, M. F., 2011. Improving
thermal performance of building walls by
optimizing insulation layer distribution and
thickness for same thermal mass. Applied
Energy, 88(2011), 3113-3124.
- [10] Ekici ,B. B., Gulten, A. A., Aksoy, U. T., 2012. A
study on the optimum insulation thicknesses of
various types of external walls with respect to
different materials, fuels and climate zones in
Turkey. Applied Energy, 92(2012),211-217.
- [11] Axaopoulos, I., Axaopoulos, P., Gelegenis, J.,
2014. Optimum insulation thickness for external
walls on different orientations considering the
speed and direction of the wind. Applied Energy,
117(2014), 167-175.
- [12] Ozel, M., 2011. Effect of wall orientation on the
optimum insulation thickness by using a
dynamic method. Applied Energy, 88(2011),
2429-2435.
- [13] Jinghua Yu, Liwei Tian, Changzhi Yang, Xinhua
Xu, Jinbo Wang, 2011. Optimum insulation
thickness of residential roof with respect to
solar-air degree-hours in hot summer and cold
winter zone of china. Energy and Buildings,
43(2011), 2304–2313.
- [14] Y.F. Li, W.K. Chow, 2005. Optimum insulationthickness
for thermal and freezing protection.
Applied Energy, 80(2005), 23-33.
- [15] Sami A. Al-Sanea, M.F. Zedan, Saleh A. Al-Ajlan,
2005. Effect of electricity tariff on the optimum
insulation-thickness in building walls as
determined by a dynamic heat-transfer model.
Applied Energy, 82(2005), 313-330.
- [16] Alireza Bahadori, Hari B. Vuthaluru, 2010. A
simple method for the estimation of thermal
insulation thickness. Applied Energy, 87(2010),
613-619.
- [17] Naouel Daouas, 2011. A study on optimum
insulation thickness in walls and energy savings
in Tunisian buildings based on analytical
calculation of cooling and heating transmission
loads. Applied Energy, 88(2011), 156-164.
- [18] Pan Dongmei, Chan Mingyin, Deng Shiming, Lin
Zhongping, 2012. The effects of external wall
insulation thickness on annual cooling and
heating energy uses under different climates.
Applied Energy, 97(2012), 313-318.
- [19] Afif Hasan, 1999. Optimizing insulation
thickness for buildings using life cycle cost.
Applied Energy, 63(1999), 115-124.
- [20] Jérôme Barrau, Manel Ibanez, Ferran Badia,
2014. Impact of the optimization criteria on the
determination of the insulation thickness.
Energy and Buildings, 76(2014), 459-469.
- [21] H. Asan, 1998. Effects of Wall’s insulation
thickness and position on time lag and
decrement factor. Energy and Buildings,
28(1998), 299-305.
- [22] Muhammet Kayfeci, Ali Keçebaş¸ Engin Gedik,
2013. Determination of optimum insulation
thickness of external walls with two different
methods in cooling applications. Applied
Thermal Engineering, 50(2013), 217-224.
- [23] Muhammet Kayfeci, İsmail Yabanova, Ali
Keçebaş, 2014. The use of artificial neural
network to evaluate insulation thickness and life
cycle costs: Pipe insulation application. Applied
Thermal Engineering, 63(2014), 370-378.
- [24] Ömer Kaynaklı, 2014. Economic thermal
insulation thickness for pipes and ducts: A
review study. Renewable and Sustainable
Energy Reviews, 30(2014), 184-194.
- [25] King-Leung Wong, Huann-Ming Chou, Bing-
Shyan Her, Huang-Ching Yeh, 2004. Complete
heat transfer solutions of an insulated regular
cubic tank with an SSWT model. Energy
Conversion and Management, 45(2004), 2813-
2831.
- [26] N. Usta, A. Ileri, 1999. Computerized economic
optimization of refrigeration system design.
Energy Conversion and Management, 40(1999),
1089-1109.
- [27] King-Leung Wong, Huann-Ming Chou, 2003.
Heat transfer characteristics of an insulated
regular polyhedron by using a regular polygon
top solid wedge thermal resistance model.
Energy Conversion and Management, 44(2003),
3015-3036.
- [28] H. Sofrata and B. Salmeen, 1993. Optimization of
insulation thicknesses using micros. Energy
Conversion and Management, 34(1993), 471-
479.
- [29] H. Demir, M. K. Sevindir, Ö. Ağra, Ş. Ö. Atayılmaz,
İ. Teke, 2015. Optimum distribution of thermal
insulation material for constant insulation material volume or a given investment cost. J. of
Renewable and Sustainable Energy, 7(2015),
063122.
- [30] M. K. Sevindir, H. Demir, Ö. Ağra, Ş. Ö. Atayılmaz,
İ. Teke, 2017. Modelling the optimum
distribution of insulation material. Renewable
Energy, 113 (2017), 74-84.
- [31] A.K. Pramancik, P.K. Das, 2005. Heuristics as an
alternative to variational calculus for
optimization of a class of thermal insulation
systems. Int. Journal of Heat and Mass Transfer,
48(2005), 1851-1857.
- [32] A. Bejan, 2000. Shape and Structure, from
Engineering to Nature. Cambridge University
Press, UK, 2000.
- [33] J. Lewins, 2002. Bejan’s constructal theory of
equal potential distribution. Int. Journal of Heat
and Mass Transfer, 46(2002), 1541-1543.