İsmaıl TOPCU, H.Ozkan GULSOY, Arıf N. GULLUOGLU

Evaluation of Multi-Walled CNT particulate reinforced Ti6Al4V alloy based composites creep behavior of materials under static loads.

This study examines the effects of additions of Carbon Nanotube (CNT) into Ti6Al4V matrix by mechanical alloying at low CNT rates and investigates into sintering conditions on the density, microstructure, and static creep behaviors. After producing Ti6Al4V composites containing different amounts of CNT by mechanical alloying and sintering at 1300°C. The density of CNT reinforced Ti6Al4V composites sintered at 1300°C for 3h decreases with increasing CNT content. The hardness tests indicated that the hardness of composites increased with CNT addition. Creep tests showed that the creep strength of composites increased with CNT content until 4% of CNT but decreased after this value. In addition, although static creep displacements are decreased continually with CNT content until 5%, static creep life increased with increasing CNT content until 4% of CNT but decreased above 4%.

Anahtar Kelimeler:

Creep, Sintering, Ti6Al4V, Carbon Nanotube

Evaluation of Multi-Walled CNT Particulate Reinforced Ti6Al4V Alloy Based Composites Creep Behavior of Materials Under Static Loads

This study examines the effects of additions of 0.5-5 v/v percentage multi-walled carbon nanotubes into the Ti-6Al-4V matrix by mechanical alloying at low rates and investigates the results of the different sintering conditions on the density, microstructure, and Creep behavior. Mechanical properties, microstructural and density of composite materials (Ti64 / CNT) produced by cold isostatic press molding method have been investigated. MWCNTs reinforced metal matrix composite powders were molded by cold isostatic pressing method using polyacrylonitrile (PAN) based binder. The binder decomposition was carried out by heat treatment. After molding, the specimens have been sintered at high temperature in high vacuum (10-2 bar). Metallographic experiments were carried out to examine density and microstructure. Experimental results indicate Ti–6Al–4V particulate can be sintered to up to 98,5% of calculated density. Maximum hardness was obtained 538 HV at 1300 oC for 3 hours and creep life inverse. By using SEM and X-ray diffractometer the characteristics of produced composite samples were investigated. Although Ti–6Al–4V alloys are used as biomaterial, this study aimed at using MWCNTs containing Ti-6Al-4V composites at high temperature applications. Because MWCNTs reinforced Ti-6Al-4V composites are cheaper and has lower weight than the other materials used in this kind of applications.

Keywords:

Creep Sintering, Ti-6Al-4V, Multi-Walled Carbon, Nanotube,

PDF

___

A.G. Jackson, J. Moteff, F.H. Froes, “Advanced titanium-alloy department via powder-metallurgy” J. Met. 31 (1979), pp. 145-145.
Z.Y. Ma, R.S. Mishra, S.C. Tjong, “High-temperature creep behavior of TiC particulate reinforced Ti-6Al-4V alloy composite” Acta Mater. 50 (2002), pp. 4293-4302.
L. Wang, Z.-B. Lang, H.-P. Shi, “Properties and forming process of prealloyed powder metallurgy Ti-6Al-4V alloy” Trans. Nonferr. Met. Soc. China. 17 (2007), pp.639-643.
J.-Q. Jiang, T.-S. Lim, Y.-J. Kim, B.-K. Kim, H.-S. Chung, “In situ formation of TiC-(Ti-6Al-4V) composites” Mater. Sci. Technol. 12 (1996), pp. 362-365.
Topcu, İ, “Determination of mechanical properties of Ceramic reinforced Al matrix composites under dynamic loading condıtıons” Master’s. Thesis, Marmara Unv.Turkey, 2007, pp. 51-58
Mamalis, A.G. Vogtländer, L.O.G. Markopoulos, A. (2004), ” Nanotechnology and nanostructured materials: trends in carbon nanotubes” Precision Eng. 28, pp. 16–30.
Baxendale, M. Mater, J. (2003),” The physics and applications of carbon nanotubes” Materials in Electronics. 14, pp. 657–659.
Thostenson, E.T. Ren, Z. Chou, T.W. (2001), “Advances in the science and technology of carbon nanotubes and their composites” Compos. Sci. Technol. 61, pp.1899–1912.
Lau, A.K. Hui, D. (2002),” The revolutionary creation of new advanced materials—carbon nanotube composites”Compos. Part B: Eng. 33, pp. 263–277.
Pipes, R.B. Hubert, P. (2002) “Helical carbon nanotube arrays: mechanical properties”Compos. Sci. Technol. 62, pp. 419–428.
Salvetat-Delmotte, J. Rubio, A. (2002) “Mechanical properties of carbon nanotubes: a fiber digest for beginners” Carbon 40, pp. 1729–1734.
Saether, E. Frankland, S.J. Pipes, R.B. (2003) “Self-consistent properties of carbon nanotubes and hexagonal arrays as composite reinforcements” Compos. Sci. Technol. 63, pp. 1543–1550.
Davey, A.P. Coleman, J. Dalton, A. Maier, S. Drury, A. Gray, D. Brennan, M. Ryder, K. Lamy De La Chapelle, M. Journet, C. (1999) “Processing of copper–carbon nanotube composites by vacuum hot pressing technique” Synth.Met. 103, pp. 2559–2562.
Valentini, L. Biagiotti, J. Kenny, J.M. Santucci, S. (2003), “Morphological characterization of single-walled carbon nanotubes-PP composites” Compos. Sci.Technol. 63, pp. 1149–1153.
Maser, W.K. Benito, A.M. Callejas, M.A. Seeger, T. Mart´ınez, M.T. Schreiber, J. Muszynski, J. Chauvet, O. Osváth, Z. Koós, A.A Biró, L.P. (2003) “Synthesis and characterization of new polyaniline/nanotube composites” Mater. Sci. Eng.: C 23, pp. 87–91.
Andrews, R. Weisenberger, M.C. (2004), “Carbon nanotube polymer composites” Current opinion in solid State Material Sciences, in press, Available online May 2004.
Ajayan, P.M. Schadler, L.S. Giannaris, C. Rubio, A. (2002), “Synthesis and characterization of plasma spray formed carbon nanotube reinforced aluminum composite”Adv. Mater. (FRG) (Germany) 12, pp. 750–753.
Wong, M. Paramsothy, M. Xu, X.J. Ren, Y. Li, S. Liao, K.(2003) “Physical interactions at carbon nanotube-polymer interface” Polymer 44, pp. 7757–7764.
Odegard, G.M. Pipes, R.B. Hubert, P. (2003) “Comparison of two models of SWCN polymer composites” Compos. Sci. Technol. 64, pp.1011–1020.
Kymakis, E. Alexandou, I. Amaratunga, G.A.J. (2002) “Single-walled carbon nanotube-polymer composites: electrical, optical and structural investigation” Synth. Met. 127, pp. 59–62.
Balázsi, Z. Kónya, F.Wéber, L. Biró, L. Arató, P. (2003) “Preparation and characterization of carbon nanotube reinforced silicon nitride composites” Mater. Sci. Eng.: C 23, pp. 1133–1137.
Rul, S. Lefèvre-schlick, F. Capria, E. Laurent, Ch. Peigney, A. (2004), “Percolation of single-walled carbon nanotubes in ceramic matrix nanocomposites” Acta Mater. 52, pp. 1061–1067.
Liu, Z , Tao, R , Ban, G , Luo, P . (). Absorbing Property of Multi-layered Short Carbon Fiber Absorbing Coating. Gazi University Journal of Science, 30 (3), 29-37. Retrieved from http://dergipark.gov.tr/gujs/issue/31190/309755
A. Peigney, E. Flahaut, Ch. Laurent, F. Chastel, A. Rousset, Chem. Phys. Lett. “Aligned carbon nantubes in ceramic-matrix nano composites prepared by high tempareture extrusion” Chem. Phys. Lett. 352 (2002), pp. 20–25.
M. R. Bafandeh, R. Gharahkhani, M.H.Fathi “Fabrication, Characterization and Osteoblast Response of Cobalt-Based Alloy/Nano Bioactive Glass Composites” Journal of Advanced Materials and Processing, Vol. 4, No. 3, 2016, pp.3-13 3
Solakoğlu, İ. Ataoğlu, Ş. Güllüoğlu,AN.” Temperature dependent mechanical characterization of styrene-acrylonitrile”. Polymer composites Volume 17, Issues 4, 2009, pp. 247-252.