___

• Fair, G.H., and Wood, J.U., “MA of ironaluminum
• intermetallics”, Powder Met., Cilt 36,
• -128, 1993.
• Hausner, H.H. and Smith, W.E., “Modern
• developments in powder metallurgy”, Metal
• Powder Int. Fed. 6(1-4), Princeton, 1973.
• Koch, C.C., “Materials synthesis by mechanical
• alloying”, Annu. Rev. Material Sci., Cilt 1,
• -2951, 1970.
• Ruhle, M. and Karlo, G., “Novel ODS
• superalloys manufacture and properties heat
• resistant materials”, Proc. of The First Int.
• Conf., 23-26: 45-59, USA, 1991.
• Tyong, J.C. and Ma, Z.Y, “Microstructural and
• mechanical characteristics of instu metal matrix
• composites”, Met. Sci. And Eng. Reports.,
• :49-113, 2000.
• Benjamin, J.S., and Bomford, M.J., “Dispersion
• strengthened aluminum made by MA”, Met.
• Trans., 8A: 1301-1305, 1977.
• Benjamin, J.S., and Schelleny, R.D., “Dispersion
• strengthened aluminum made by MA”, Met.
• Trans. 12: 1827-1832, 1981.
• Kobayashi, K.F., Tachibana, N., and Shingu,
• P.H., “Formation of amorphous Al-Cr alloys by
• mechanical alloying”, J. of Met. Sci., 25: 3149-
• , 1983.
• Koch, C.C., Cavin, O.B., Mc Kamey, C.G., and
• Scabrough, J.O., “Preparation of amorphous
• Ni60Nb40 by MA”, Appl. Phys. Lett., 43: 1017-
• , 1983.
• Barlow, I.C., Jones, H., and Rainforth, “The
• effects of dislocations and grain boundaries on
• the coarsening Al4C3 dispersoids at 600 °C ın two
• mechanically alloyed A-Ti-O-C based materials”,
• Scripta Materiallia, 44:1089-1093, 2001.
• Jangg, G., Selesar, M., Besterci, M., Durisin, J.
• and Schroder, K., “Influence of heat treatment
• during manufacturing of Al-Al4C3 materials on
• microstructure and properties”, Pow. Met. Int.,
• -30, 1989.
• Besterci, M., Selesar, M., and Kovac, L.,
• “Influence of strain rate on fracture of dispersions
• strengthened Al-Al4C3 systems”, Scripta
• Materialia, 37:1077-1080, 1997.
• Barlow, I.C., Jones, H., and Rainforth, W.M.,
• “Coarsening kinetics at 6000C of Al4C3
• disporsoid in mechanically alloyed Al-Ti-O-C”,
• Scripta Materialia, 44:79-86, 2001.
• Bostan, B., Özdemir, A. T. and Kalkanlı, A.,
• "Microstructure Characteristics in Al-C System
• After Mechanical Alloying and High Temperature Annealing", Pow. Metall. Int.,
• Vol:47 Iss:1 p: 37-42 January 2004
• Bostan B. Kalkanlı A., and Özdemir A.T.
• “Assessment of horizontal attritor in the
• manufacture of Al-C synthesized composites via
• mechanical alloying” Euro PM 2003 October
• -22 /2003 Spain.
• Bostan, B., Özdemir A., “Alüminyum ve karbon
• tozlarının sentezlenmesi, çift pres ve çift
• sinterleme sonrası karakterizasyonu 4th
• International Powder Metallurgy Conference
• May 18-22, 2005, Turkish Powder Metallurgy
• Association Sakarya University, Sakarya, Turkey,
• -464