Eliptik Dişli Tasarımı, İmalatı, Analizi ve Eliptik Dişlilerin Endüstriyel Uygulamaları
Eliptik dişliler üzerine yapılan çalışmaların diş profillerinin tasarımı üzerine yoğunlaştığı ve prototip imalatlarına yönelik araştırmaların arttığı görülmektedir. Eliptik dişlilerin diş profillerinin silindirik dişliler gibi özdeş olmayacağından hareketle geliştirilen eliptik dişlinin diş profili; kramayer veya silindirik düz dişli formlu kesicinin bölüm elipsi üzerinde yuvarlanma yöntemine uygun olarak evolvent eğriye sahip diş yanaklarının şekillendirilmesiyle elde edilmektedir. Eliptik dişlilerin imalatında CNC tel erozyon tezgahlarından faydalanmanın yaygınlaştığı, bununla birlikte azdırma tezgâhları için elektronik dişli kutuları geliştirilerek eliptik dişlilerin standart modülde imalatının da mümkün olduğu tespit edilmiştir. Eliptik dişli çiftleri farklı makine ve teçhizatta kullanılmakta, özellikle eliptik dişli çiftine sahip debimetre ve pompaların yaygınlaştığı görülmektedir. Enerji verimliliğinin son derece önem kazandığı günümüzde, yüksek akışkan miktarlarının doğru ve hassas ölçülmesi ve işletmelerin akışkan transferindeki kayıplarının giderilmesi de gerekmektedir. Bu genel değerlendirme çalışmasında eliptik dişlilerin tasarımı, geleneksel ve geleneksel olmayan imal usulleri ile imalatı, dayanım ve titreşim analizleri ve literatürde yer alan muhtelif endüstriyel uygulamaları gözen geçirilmiş ve çalışmanın ortak bulguları elde edilmiştir. Eliptik dişlilerin yakın gelecekte bünyesinde mekanik kısım barındıran birçok akıllı ürünün vazgeçilmez bir organı olacağı öngörülmektedir.
Elliptical Gear Design, Manufacturing, Analysis, and Their Industrial Practises
The studies covered elliptical gears focus on the design of tooth profiles and the researches increase about prototype manufacturing of elliptical gears. Elliptical gear tooth profile, which is developed based on the fact that the tooth profiles of elliptical gears are not identical to cylindrical gears; It is obtained by shaping tooth flanks with involute curves in accordance with the rolling method on the section ellipse with a rack or cylindrical spur gear cutter. It has been determined that the use of CNC electrical discharge machining (EDM) in the manufacture of elliptical gears has preferably become, also, the manufacturability of elliptical gears in standard modules by developing electronic gearboxes for hobbing machines. Elliptical gear pairs are used into different machines, mechanism and equipments, especially flow meters, and pumps with elliptical gear pairs are seen to be widespread. In today's world, where energy efficiency is of utmost importance, accurate and precise measurement of high fluid amounts and eliminating the losses in the fluid transfer of enterprises are also required. In this review study, the design of elliptical gears, traditional and non-traditional manufacturing methods, strength and vibration analyzes, and various industrial applications in the literature were evoluated and the common result of the literatüre works were obtained. It is predicted that elliptical gears will be an indispensable part of many smart products that contain mechanical parts in the near future.
___
- Referans1
Addomine M., Figliolini G., Pennestrì E., “A landmark in the history of non-circular gears design: The mechanical masterpiece of Dondi’s astrarium,” Mech. Mach. Theory, vol. 122, pp. 219–232, Apr. 2018, doi: 10.1016/j.mechmachtheory.2017.12.027.
- Referans2
LAI M. J., “An Investigation of The Dynamic Behaviour of Systems With, Noncircular Gears,” Cnkijournal, Beijing, pp. 377–388, 1996.
- Referans3
Mundo D., “Geometric design of planetary gear train with non-circular gears,” Mech. Mach. Theory Elsevier Ltd, pp. 456–472, 2006.
- Referans4
Yao Y. A., Yan H. S., “A new method for torque balancing of planar linkages using non-circular gears,” Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 217(5), pp. 495–503, 2003.
- Referans5
Chang S. L., Tsay C. B., Wu L.I., “Mathematical model and undercutting analysis of elliptical gears generated by rack cutters,” Mech. Mach. Theory, vol. 31, no. 7, pp. 879–890, 1996, doi: 10.1016/0094-114X(95)00121-E.
- Referans6
Litvin F. L., “Gear Geometry and Applied Theory,” PTR Prentice-Hall, New Jersy, pp. 300–400, 1994.
- Referans7
Gang L., Weidong Z., “Design and power loss evaluation of a noncircular gear pair for an infinitely variable transmission,” Mech. Mach. Theory, vol. 156, 2021.
- Referans8
Junfeng W., Xiaobo L., Chuan L., Bo L., Fangyan Z., “Three-dimensional design and motion analysis of non-circular gear [J].,” J. hubei Univ. Technol., vol. 29(04), pp. 69–72, 2014.
- Referans9
Medvecká-Beňová S., “Desıgnıng pıtch curves of non-cırcular gears,” Sci. J. Silesian Univ. Technol. Ser. Transp., vol. 99, pp. 105–114, Jun. 2018, doi: 10.20858/sjsutst.2018.99.10.
- Referans10
Tong S. H., Yang C. H., “Generation of Identical Noncircular Pitch Curves,” ASME J. Mech. Des., vol. 120(2), pp. 337–341, 1998.
- Referans11
Litvin F. L., Fuentes A., “Gear Geometry and Applied Theory,” Cambridge Univ. Press. New York, 2004.
- Referans12
Chung D. D., Wolfgramm R., “Maxillary arch perimeter prediction using Ramanujan’s equation for the ellipse,” Am. J. Orthod. Dentofac. Orthop., vol. 147, no. 2, pp. 235–241, 2015, doi: 10.1016/j.ajodo.2014.10.022.
- Referans13
Pazarkaya İ., Özdemir A., “Eliptik dişli çarklarda bölüm elipsinin analitik olarak hesaplanması,” 1. ULUSLARARASI MÜHENDİSLİK BİLİMLERİ VE MULTİDİSİPLİNER YAKLAŞIMLAR KONGRESİ, pp. 490–498, 2021.
- Referans14
Han J., Li D. Z., Gao T., Xia L., “Research on Obtaining of Tooth Profile of Non-circular Gear Based on Virtual Slotting,” 14th IFToMM World Congr. (Taipei Taiwan), no. URL:http://www.iftomm2015.tw/IFToMM2015CD/PDF/PS6-001.pdf, pp. 25–30, 2015.
- Referans15
Wang X., “A numerical algorithm of tooth profile of non-circular cylindrical gear,” in AIP Conference Proceedings, Jul. 2017, vol. 1864, doi: 10.1063/1.4992991.
- Referans16
Lyashkov A. A., Panchuk K. L., Khasanova I. A., “Automated Geometric and Computer-aided Non-Circular Gear Formation Modeling,” in Journal of Physics: Conference Series, Jul. 2018, vol. 1050, no. 1, doi: 10.1088/1742-6596/1050/1/012049.
- Referans17
Bair B. W., “Computer aided design of elliptical gears with circular-arc teeth,” Mech. Mach. Theory, vol. 39, no. 2, pp. 153–168, Feb. 2004, doi: 10.1016/S0094-114X(03)00111-3.
- Referans18
Betten J., “involute of an ellipse,” Math. Model. Mater. Sci. Contin. Mech. Augustinerbach, pp. 4–20, 2009.
- Referans19
Han J., Li D., Xia L., Jiang B., “Research on design method of non-circular gear pair with double generating angles, , Computer Aided Drafting,” Des. Manuf. Vol., vol. 25, p. 52, 2015.
- Referans20
Yazar M., Özdemir A., “Computer-aıded desıgn, manufacture and experımental analysıs of a paır of ellıptıcal spur gears,” ANADOLU Univ. J. Sci. Technol. A - Appl. Sci. Eng., vol. 17, no. 5, pp. 869–869, Dec. 2016, doi: 10.18038/aubtda.279855.
- Referans21
Hou Y., Lin C., “Kinematic analysis and experimental verification of an oval noncircular bevel gears with rotational and axial translational motions,” . J. Braz. Soc. Mech. Sci. Eng., p. 60, 2019.
- Referans22
Prikhodko A., “Experimental kinematic analysis of an intermittent motion planetary mechanism with elliptical gears,” J. Meas. Eng., vol. 8, pp. 122–131, 2020.
- Referans23
Maláková S., Urbanský M., Fedorko G., Molnár V., Sivak S., “Design of geometrical parameters and kinematical characteristics of a non‐circular gear transmission for given parameters,” Appl. Sci., vol. 11, no. 3, pp. 1–24, Feb. 2021, doi: 10.3390/app11031000.
- Referans24
Zhou K., Guo Y., Li X., “Modeling and Dynamics Analysis of Non-Circular Gears,” in PervasiveHealth: Pervasive Computing Technologies for Healthcare, Apr. 2020, pp. 442–447, doi: 10.1145/3436286.3436434.
- Referans25
Zheng F., Hua L., Chen D., Han X., “Generation of Noncircular Spiral Bevel Gears by Face-Milling Method,” ASME J. Manuf. Sci. Eng., vol. 138(8), p. 081013, 2016.
- Referans26
Litvin F. L., Gonzalez-Perez I., Yukishima K., Fuentes A., Hayasaka K., “Generation of planar and helical elliptical gears by application of rack-cutter, hob, and shaper,” Comput. Methods Appl. Mech. Eng., vol. 196, no. 41–44, pp. 4321–4336, 2007, doi: 10.1016/j.cma.2007.05.003.
- Referans27
Katz A., Erkorkmaz K., Ismail F., “Virtual Model of Gear Shaping— Part I: Kinematics, Cutter–Workpiece Engagement, and Cutting Forces,” ASME J. Manuf. Sci. Eng., vol. 140(7), p. 071007, 2018.
- Referans28
Bair B. W., “Computerized tooth profile generation of elliptical gears manufactured by shaper cutters,” J. Mater. Process. Technol., vol. 122, no. 2–3, pp. 139–147, 2002, doi: 10.1016/S0924-0136(01)01242-0.
- Referans29
Li J., Wu X., Mao S., “Numerical computing method of noncircular gear tooth profiles generated by shaper cutters,” Int. J. Adv. Manuf. Technol., vol. 33, no. 11–12, pp. 1098–1105, 2007, doi: 10.1007/s00170-006-0560-0.
- Referans30
Zheng F., Hua L., Han X., Li B., Chen D., “Linkage model and manufacturing process of shaping non-circular gears,” Mech. Mach. Theory, vol. 96, pp. 192–212, 2016, doi: 10.1016/j.mechmachtheory.2015.09.010.
- Referans31
Zheng F., Hua L., Han X., Li B., Chen D., “Synthesis of Shaped Noncircular Gear Using a Three-Linkage Computer Numerical Control Shaping Machine,” J. Manuf. Sci. Eng. Trans. ASME, vol. 139, no. 7, 2017, doi: 10.1115/1.4035794.
- Referans32
Zheng F., Guo X., Zhang M., “Non-uniform flank rolling measurement for shaped noncircular gears,” Meas. J. Int. Meas. Confed., vol. 116, pp. 207–215, Feb. 2018, doi: 10.1016/j.measurement.2017.07.048.
- Referans33
Zheng F., Lin H., Han X., Zhang M., Zhang W., Guo X., “Avoidance of Cutter Retracting Interference in Noncircular Gear Shaping Through 4-Linkage Model,” J. Manuf. Sci. Eng. Trans. ASME, vol. 141, no. 5, 2019, doi: 10.1115/1.4043193.
- Referans34
Zheng F., Xinghui H., Hua L., Zhang M., zhang W., “Design and manufacture of new type of non-circular cylindrical gear generated by face-milling method,” Mech. Mach. Theory, vol. 122, pp. 326–346, 2018, doi: 10.1016/j.mechmachtheory.2018.01.007.
- Referans35
Tian X., Han J., Xia L., Wu L., “A fexible electronic helical guide controller,” Procedia CIRP, vol. 56, pp. 173–177, 2016.
- Referans36
Han J., Wu L., Yuan B., Tian X., Xia L., “A novel gear machining CNC design and experimental research,” Int J Adv Manuf Tech, vol. 88, pp. 1711–1722, 2016.
- Referans37
Wu J., Han J., Zhu Y., Tian X., Xia L., “Non-circular gear continuous generating machining interpolation method and experimental research,” J. Brazilian Soc. Mech. Sci. Eng., vol. 39, no. 12, pp. 5171–5180, 2017, doi: 10.1007/s40430-017-0873-y.
- Referans38
Han J., Li D., Tian X., Xia L., “Linkage model and interpolation analysis of helical non-circular gear hobbing,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 42, no. 11. 2020, doi: 10.1007/s40430-020-02663-1.
- Referans39
Dan W., Ken C., Xiankui W., “An investigation of practical application of variable spindle speed machining to noncircular turning process,” Int J Adv Manuf Technol, vol. 44, pp. 1094–1105, 2009.
- Referans40
Dan W., Tong Z., ChenXiankui W., “Application of active disturbance rejection control to variable spindle speednoncircular turning process,” Int. J. Mach. Tools Manuf., vol. 49, pp. 419–423, 2009.
- Referans41
Li Q., Ai W., Chen B., “Variable angle compensation control of noncircular turning,” Int J Adv ManufTechnol, vol. 70(1):735, p. 46, 2014.
- Referans42
Yang J., Rao P., Chen B., Ding H., Ai W., “Form error on-line estimation and compensation for non-circular turning process,” Int. J. Mech. Sci., vol. 184, no. May, 2020, doi: 10.1016/j.ijmecsci.2020.105847.
- Referans43
Jiang H., Dazhu L., Xiaoqing T., Lian X., “Meshing principle and transmission analysis of a beveloid non-circular gear,” Adv. Mech. Eng., vol. 12(11), pp. 1–11, 2020.
- Referans44
Liu Y., Gong J., Wu X., “Investigation on the grinding of elliptical gears with CNC conical wheel gear grinder,” Int. J. Adv. Manuf. Technol., vol. 64, no. 1–4, pp. 349–356, 2013, doi: 10.1007/s00170-012-4028-0.
- Referans45
Sałaciński T., Przesmycki A., Chmielewski T., “Technological aspects in manufacturing of non-circular gears,” Appl. Sci., vol. 10, no. 10, 2020, doi: 10.3390/app10103420.
- Referans46
Yazar M., “Design, Manufacturing and Operational Analysis of Elliptical Gears,” Int. J. Precis. Eng. Manuf., vol. 22, no. 8, pp. 1441–1451, 2021, doi: 10.1007/s12541-021-00549-3.
- Referans47
García-Hernández C., Gella-Marín R. M., Huertas-Talón J. L., Efkolidis N., Kyratsis P., “WEDM manufacturing method for noncircular gears, using CAD/CAM software,” Stroj. Vestnik/Journal Mech. Eng., vol. 62, no. 2, pp. 137–144, 2016, doi: 10.5545/sv-jme.2015.2994.
- Referans48
Lai M., “An investigation of the dynamic behavior of systems with noncircular gears,” hD Thesis, Univ. Wisconsin-Madison, USA., 1997.
- Referans49
Kahraman A., Singh R., “Non-linear dynamics of a spur gear pair,” J. Sound Vib., vol. 142, pp. 49–75, 1990.
- Referans50
Gao N., Meesap C., Wang S., Zhang D., “Parametric vibrations and instabilities of an elliptical gear pair,” JVC/Journal Vib. Control, vol. 26, no. 19–20, pp. 1721–1734, 2020, doi: 10.1177/1077546320902543.
- Referans51
Lin J., Parker R. G., “Mesh stiffness variation instabilities in two-stage gear systems,” J. Vib. Acoust., vol. 124(1), pp. 68–76, 2002.
- Referans52
Karpov O., Nosko P., Fil P., “Prevention of resonance oscillations in gear mechanisms using non-circular gears,” Mech. Mach. Theory, vol. 114, pp. 1–10, 2017.
- Referans53
Liu X., Nagamura K., Ikejo K., “Simulation on the vibration characteristics of elliptical gears,” Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 227, no. 4, pp. 819–830, 2013, doi: 10.1177/0954406212454372.
- Referans54
Lıu X., Nagamura K., Ikejo K., “Analysis of the dynamic characteristics of elliptical gears,” J. Adv. Mech. Des., vol. 6, p. 4, 2012.
- Referans55
Maláková S., “Teeth deformatıon of non-cırcular gears,” Sci. J. Silesian Univ. Technol. Ser. Transp., vol. 110, 2021.
- Referans56
Liu D. W., Zhi R., Xin J., “Dynamic model and its application of transmission system in noncircular gears,” J. Mach. Des., vol. 33(1), pp. 35–39, 2016.
- Referans57
Zhou K., Li Y., Wang C., Li C., “Non-circular Gear Modal Analysis Based on ABAQUS,” in Proceedings - 8th International Conference on Intelligent Computation Technology and Automation, ICICTA 2015, May 2016, pp. 576–579, doi: 10.1109/ICICTA.2015.147.
- Referans58
Vanegas-Useche L. V., Abdel-Wahab M. M., Parker G. A., “Nuevo par de engranajes no circulares para reducir las aceleraciones del eje: Comparación con engranajes sinusoidales y elípticos,” DYNA, vol. 83, no. 198, pp. 220–228, Sep. 2016, doi: 10.15446/dyna.v83n198.49170.
- Referans59
Zhou K., Li Y., Li C., Wang C., “Non-circular Gear Kinematics Simulation Based on ADAMS,” Proc. - 8th Int. Conf. Intell. Comput. Technol. Autom. ICICTA 2015, pp. 572–575, 2016, doi: 10.1109/ICICTA.2015.146.
- Referans60
Waldron K. J., Kinzel G. L., Agrawal S. K., “Kinematics, Dynamics, and Design of Machinery, 3th Edition,” Wiley, New York, 2004.
- Referans61
Sun Z. X., Hebbale K., “Challenges and opportunities in automotive transmission control,” Proc. 2005 Am. Control Conf. Portl., pp. 3284–3289, 2005.
- Referans62
Wang X. F., Zhu W. D., “Design, modeling, and simulation of a geared infinitely variable transmission,” ASME J. Mech. Des, vol. 136(7), p. 071011, 2014.
[63] Litvin F., Fuentes-Aznar A., “Noncircular Gears: Design and Generation,” Cambridge Univ. Press. New York, 2009.
- Referans64
Prikhodko A. A., Smelyagin, A. I., “Kinematic analysis of mechanism for converting rotational motion into reciprocating rotational motion,” Procedia Eng., vol. 129, pp. 87–92, 2015.
- Referans65
Lee G. S., Park M. Y., “Flow fıeld characterıstıcs ın the housıng of noncırcular gear flowmeter,” no. July, 2008.
- Referans66
Liu D., Ba Y., Ren T., “Flow fluctuation abatement of high-order elliptical gear pump by external noncircular gear drive,” Mech. Mach. Theory, vol. 134, pp. 338–348, 2019, doi: 10.1016/j.mechmachtheory.2019.01.011.
- Referans67
Moinfar A. M., Shahgholi G., Gilandeh Y. A., Gundoshmian T. M., “The effect of the tractor driving system on its performance and fuel consumption,” Energy, vol. 202, p. 117803, 2020, doi: 10.1016/j.energy.2020.117803.
- Referans68
Rongping K., “Port Ship Energy Consumption Management Based On Beidou Satellite Communication[J],” Jimei Univ., 2017.
- Referans69
Firth J., Ladouceur F., Brodzeli Z., Wyres M., Silvestri L., “A novel optical telemetry system applied to flowmeter networks,” Flow Meas. Instrum., vol. 48, pp. 15–19, 2016, doi: 10.1016/j.flowmeasinst.2016.01.006.
- Referans70
Zaza A., Bennouna E. G., Laadel N. E., El Hammami Y., “Experimental Study of Fouling in Hybrid Cooling Tower Used in CSP Plants: Effects of the Polymer and galvanized steel tubes,” Therm. Sci. Eng. Prog., vol. 25, no. June, p. 101005, 2021, doi: 10.1016/j.tsep.2021.101005.
- Referans71
Xiao L., Yang M., Zhao S., Yuan W. Z., Huang S. M., “Entropy generation analysis of heat and water recovery from flue gas by transport membrane condenser,” Energy, vol. 174, pp. 835–847, 2019.
- Referans72
Soleimanikutanaei S., Lin C. X., Wang D., “Numerical modeling and analysis of Transport Membrane Condensers for waste heat and water recovery from flue gas,” Int J Therm Sci, vol. 136, pp. 96–106, 2019.
- Referans73
Yang Y., Li N. F., Huang S. M., Liang C. H., Xiao L., “State-space model for transient behavior of transport membrane condenser,” Int. J. Heat Mass Transf., vol. 165, 2021, doi: 10.1016/j.ijheatmasstransfer.2020.120667.
- Referans74
Meribout M., Azzi A., Ghendour N., Kharoua N., Khezzar L., AlHosani E., “Multiphase Flow Meters Targeting Oil & Gas Industries,” Meas. J. Int. Meas. Confed., vol. 165, p. 108111, 2020, doi: 10.1016/j.measurement.2020.108111.
- Referans75
Li X., Huang Z., Meng Z., Wang B., Li H., “Oil-water two-phase flow measurement using a venturi meter and an oval gear flow meter,” Chem. Eng. Commun., vol. 197, no. 2, pp. 223–231, 2010, doi: 10.1080/00986440902938469.
- Referans76
Yan J., Li S., Li R., “Numerical study on the auxiliary entrainment performance of an ejector with different area ratio,” Appl. Therm. Eng., vol. 185, no. August 2020, p. 116369, 2021, doi: 10.1016/j.applthermaleng.2020.116369.
- Referans77
Park J. J, Lee E. S., “A study on the elliptical gear design for oval flowmeter,” Trans. Korean Soc. Mech. Eng. A, vol. 37, no. 8, pp. 1029–1033, 2013, doi: 10.3795/KSME-A.2013.37.8.1029.
- Referans78
Yazar M., Özdemir A., “Eliptik Düz Dişlilerin Bilgisayar Destekli Tasarımı ve CNC Tel Erozyon ile İmalatı,” Politek. Derg., vol. 13, pp. 245–253, 2010.