ATKI İPLİK NUMARASI VE ATKI SIKLIĞININ HAM VE AĞARTILMIŞ DİMİ 3/1(S) DOKUMA KUMAŞLARDA İPLİK KIVRIMINA ETKİSİ

Bu çalışmada, dimi 3/1 (S) örgü yapısındaki ham ve ağartılmış dokuma kumaşlarda atkı iplik numarası ve atkı sıklığının kıvrım üzerindeki etkisi araştırılmıştır. Çözgü iplik özelliklerini değiştirmemek kaydıyla (tip, iplik numarası ve çözgü sıklığı), atkı iplik numarası ve atkı sıklığını değiştirmek suretiyle kumaş üretimi gerçekleştirilmiştir. Kıvrım yüzdesi, dokuma makinesi çıkışında ham ve ağartılmış kumaşlarda, kumaştan çıkarılarak ölçülen kıvrımsız gerçek iplik uzunluğu ile kumaş yapısındaki iplik uzunluğu arasındaki farkın, kumaş yapısındaki iplik uzunluğuna yüzdesel oranı olarak hesaplanmıştır. Atkı iplik numarası ve atkı sıklığının, dokuma kumaştaki çözgü ve atkı iplik kıvrımı üzerinde istatistiksel olarak anlamlı etkisinin olduğu gözlenmiştir. Ayrıca, ağartma işleminden sonra atkı sıklıklarında meydana gelen değişikliğin bir sonucu olarak, ağartılmış kumaşların atkı ve çözgü kıvrım yüzdelerinin ağartılmamış kumaşlardan daha yüksek değerlere sahip olduğu görülmüştür.

EFFECTS OF WEFT COUNT AND WEFT DENSITY ON YARN CRIMP% OF UNBLEACHED AND BLEACHED 3/1(S) TWILL WOVEN FABRICS

In this study, the effects of weft yarn count and weft density on crimp% of unbleached and bleached 3/1(S) twill woven fabrics are investigated. The warp yarn properties (type, count and warp density) were kept constant while the effect of variation in weft count and weft density were studied. Crimp% of unbleached and bleached fabrics are calculated by dividing the difference between straightened yarn length and the distance between the ends of the yarn while in the fabric, by the distance between the ends of the yarn while in the fabric as percentage. It is observed that the crimp% of warp and weft yarn in woven fabric is effected by weft count and weft density statistically. Moreover weft and warp crimp% of bleached fabrics have higher values than unbleached fabrics as a result of the change in weft densities after bleaching process.

___

  • 1. Kovar, R., (2011), Length of the yarn in plain-weave crimp wave, The Journal of The Textile Institute, 102(7):582-597.
  • 2. Haque, Md. M., (2009), Effect of weft parameters on weaving performance and fabric properties, Daffodil International University Journal of Science and Technology, 4(2):62-69.
  • 3. Peirce, F T., (1937), The geometry of cloth structure, The Journal of the Textile Institude, 28:45-96
  • 4. Behera, BK., Militky, J., Mishra , R., Kremenakova, D., (2012), Modeling of woven fabric geometry and properties, Woven Fabrics, Prof. Han-Yong Jeon (Ed.), In Tech, 1-32, ISBN 978-953-51-0607- 4.
  • 5. Mertova I, Neckar B, Ishtia que SM., (2016), New method to measure yarn crimp in woven fabric, Textile Research Journal, 86(10):1084-1096
  • 6. Saiman, M.P., Wahab, M.S., Wahit, M.U., (2014), The Effect of Fabric Weave on the Tensile Strength of Woven Kenaf Reinforced Unsaturated Polyester Composite. In: Ahmad M., Yahya M. (eds) Proceedings of the International Colloquium in Textile Engineering, Fashion, Apparel and Design 2014 (ICTEFAD 2014), 25-29, 25 August 2014, Springer, Singapore
  • 7. Hu, J., (2004), Structure and mechanics of woven fabrics, Woodhead Publishing Limited in association with The Textile Institute Woodhead Publishing Ltd, England
  • 8. Behera, BK., Ishtiaque, SM., Chand, S., (1997), Comfort properties of fabrics woven from ring-,rotor and friction-spun yarns, The Journal of The Textile Institude, 88(3):255-264.
  • 9. Tayyar, A. E., Sari, F., Yağiz, İ., (2011), Gömleklik kuma şlarda yapısal parametrelerin kumaşın aşınma direncine etkileri, Tekstil ve Mühendis, 18(84):23-26.
  • 10. Mishra, S., Majumdar, A., Butola, BS., (2014), Modeling of yarn strength utilization in cotton woven fabrics using multiple linear regression, Journal of Engineered Fibers and Fabrics, 9(2):105-111.
  • 11. Akgun, M., (2015), Effect of yarn filament fineness on the surface roughness of polyester woven fabrics, Journal of Engineered Fibers and Fabrics, 10(2):121-128.
  • 12. Süle, G., (2009), Dokuma kuma şlarda çözgü gerginliği ile kıvrım ilişkisinin teorik analizi. Uludağ Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi, 14(1):127-138.
  • 13. Afroz, F., Siddika, A., (2014), Effect of warp yarn tension on crimp% in woven fabric. Europan Scientific Journal, 10(24):202- 207.
  • 14. Siddika, A., Akter, N. N., Saha, K., Islam, Md.M., Islam, M.M., (2015), Effects of yarn count on crimp% and take-up% of 2/1(S) twill woven fabric. Global Journal of Researches In Engineering:1 General Engineering, 15(6):54-59.
  • 15. Maqsood, M., Hussain, T., Nawab, Y., Shaker, K., Umair, M., (2015), Prediction of warp and weft yarn crimp in cotton woven fabrics, The Journal of The Textile Institude, 106(11):1180-1189.
  • 16. Tan, VBC., Shim, VPW., Zeng, X., (2005), Modelling crimp in woven fabrics subjected to ballistic impact, International Journal of Impact Engineering, 32:561-574.
  • 17. Backer, S., (1948), The relationship between the structural geometry of a textile fabric and its physical properties, Textile Research Journal, 18(11),650-658.
  • 18. Mohamed, MH., Lord, PR., (1973), Comparison of physical properties of fabrics woven fro m open-end and ring spun yarns, Textile Research Journal, 43(3),154-166.
  • 19. Kullman, RMH., Grah am, CO., Ruppenicker, GF., (1981), Air permeability of fabrics made from unique and conventional yarns, Textile Research Journal, 51(12), 781-786.
  • 20. Ajayi, JO., (1992), Effects of dabric structure on frictional properties, Textile Research Journal, 62(2),87-93.
  • 21. Peled, A., Bentur, A ., Yankelevsky, D., (1998 ), Effects of woven fabric geometry on the bonding performance of cementitious composites. Advanced Cement Based Materials, 7(1), 20-27.
  • 22. Chattopadhyay, R., (2008), Design of apparel fabrics:role of fibre, yarn and fabric parameters on its functional attributes, Journal of Textile Engineering, 54(6):179-190.
  • 23. Bhattacharjee, D., Kothari, VK ., (2009), Heat transfer through woven textiles, International Journal of Heat and Mass Transfer, 52, 2155-2160.
  • 24. Akgun, M., (2014), Assessment of the surface roughness of cotton fabrics through different yarn and fabric structural parameters, Fibers and Polymers, 15(2):405-413.
  • 25. Brand, RH., SCRUBY, RE., (1973), Three-dimensional geometry of crimp, Textile Research Journal, 43(9), 544-554.
  • 26. Leaf, GAV., Anandjiwala, RD., (1985), A generalized model of plain woven fabric, Textile Research Journal, 55(2), 92-99.
  • 27. Lomov, SV., Gusakov, AV., Huysmans, G., Prodromou, A., Verpoest, I., (2000), Textile geometry preprocessor for meso- mechanical models of woven composites, Composites Science and Technology, 60:2083-2095.
  • 28. Jeon, BS., Chun, SY., Hong, CJ., (2003), Structural and mechanical properties of woven fabrics employing Peirce’s model, Textile Research Journal, 73(10), 929-933.
  • 29. Behera, BK., Muttagi, SB., (2006), Engineering design of polyester- viscose blended suiting fabrics using radial basis function network:part II-prediction of fabric constructional parameters from its properties, Indian Journal of Fibre&Textile Research, 31:489- 495.
  • 30. Başer, G., (2015), Modeling of complex fabric structures by methods of computer simulation. Tekstil ve Mühendis, 22(98):1-16.
  • 31. Özdemir, H., Başer, G., (2009), Computer simulation of plain woven fabric appearance from yarn photographs. The Journal of The Textile Institude, 100(3):282-292.
  • 32. Akgün, M., (2013), The Effect of Fabric Balance and Fabric Cover on Surface Roughness of Polyester Fabrics. Fibers and Polymers, 14(8):1372-1377
  • 33. Akgün, M., Alpay, H.R., Becerir, B., (2012), Bazi Poliester Dokuma Kumaşlarin Çözgü Ve Atki İpliklerinin Dokuma İşlemi Öncesi Ve Sonrasi Reflektans Özelliklerindeki De ğişimlerin İncelenmesi. Uludağ Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi, 17(2):91-104
  • 34. Tabachnick, BG., Fidell, LS., (2014), Using Multivariate Statistics, Pearson Education Limited, Boston.
  • 35. George, D., Mallery, M., (2010). SPSS for Windows Step by Step: A Simple Guide and Reference, 17.0 update, Allyn & Bacon, Boston
Tekstil ve Mühendis-Cover
  • ISSN: 1300-7599
  • Yayın Aralığı: Yılda 4 Sayı
  • Başlangıç: 1987
  • Yayıncı: TMMOB Tekstil Mühendisleri Odası
Sayıdaki Diğer Makaleler

GİYSİLİK DERİLERİN HASLIK ÖZELLİKLERİNİN TiO2/SiO2/GLYMO ESASLI NANOKOMPOZİT ÇÖZELTİSİ VE LAK KAPLAMASI İLE İYİLEŞTİRİLMESİ

Meruyert KOİZHAİGANOVA KAYGUSUZ

SPUNBOND DOKUSUZ TEKSTİL YÜZEYİ ÜZERİNE ELEKTRO ÇEKİM YÖNTEMİ İLE NANO BOYUTTA GRAFEN KAPLANMASI VE KARAKTERİZASYONU

M. Hakkı ALMA, MUSTAFA YAZICI, Behzat YILDIRIM, TUFAN SALAN, İSMAİL TİYEK

Elektronik Tekstillere Yönelik Akıllı Kumaş Sensörleri

Ayşe Didem EROL, Suat ÇETİNER

Kompozit Malzeme Üretiminde Kullanılacak Bitkisel Liflerin Alkali Modifikasyonu Sonrası Morfolojik ve Kimyasal Yapılarındaki Değişimin İncelenmesi

Yasemin SEKİ, Figen SELLİ, Korhan ŞEN, Ümit Halis ERDOĞAN

Kesikli Poliester ve Dış/İç Düşük Sıcaklıkta Eriyen Kesikli Poliester Bağlayıcı Liflerinden Tarak, İğneleme ve Pres Makineleri ile Üretilmiş Dokunmamış Kumaşların Mukavemet Özellikleri Üzerine Bir Araştırma

Mustafa Sabri ÖZEN

Atkı İplik Numarası ve Atkı Sıklığının Ham ve Ağartılmış Dimi 3/1(S) Dokuma Kumaşlarda İplik Kıvrımına Etkisi

Deniz Mutlu ALA, Gamze Gülşen BAKICI

ATKI İPLİK NUMARASI VE ATKI SIKLIĞININ HAM VE AĞARTILMIŞ DİMİ 3/1(S) DOKUMA KUMAŞLARDA İPLİK KIVRIMINA ETKİSİ

DENİZ MUTLU ALA, GAMZE GÜLŞEN BAKICI

Giysilik Derilerin Haslık Özelliklerinin TiO2/SiO2/GLYMO Esaslı Nanokompozit Çözeltisi ve Lak Kaplaması ile İyileştirilmesi

Meruyert (KOİZHAİGANOVA) KAYGUSUZ

Ribana Kumaşların Hava ve Su Buharı Geçirgenliklerine İlmek ve Atlama Kombinasyonların Etkisi

Palanisamy KANAKARAJ, Rajagopalan RAMACHANDRAN

KOMPOZİT MALZEME ÜRETİMİNDE KULLANILACAK BİTKİSEL LİFLERİN ALKALI MODIFIKASYONU SONRASI MORFOLOJIK VE KİMYASAL YAPILARINDAKI DEGIŞIMIN İNCELENMESİ

YASEMİN SEKİ, Figen SELLİ, Korhan ŞEN, ÜMİT HALİS ERDOĞAN