Toz Metal Al7075/B4C/Si3N4 Kompozit Malzemelerin Üretimi ve Aşınma Özelliklerinin İncelenmesi

Bu çalışmada,  bir alüminyum alaşımı olan saf Al7075 ile  Al7075/B4C ve Al7075/B4C/Si3N4 kompozit malzemeleri toz metalurjisi yöntemi ile üretilmiştir. Üretilen kompozitlerde ön alaşımlı Al7075 tozları kompozit matrisini oluştururken, B4C ve Si3N4 seramik parçacıkları takviye elemanı olarak kullanılmıştır.  Ağırlıkça karışım oranları belirlenen tozlar 3 boyutlu karıştırıcıda 15 dakika boyunca karıştırılmıştır. Karışım tozlar önceden ısıtılan sıcak presleme kalıbında 450 oC sıcaklıkta 30 dakika boyunca tek yönlü olarak preslenmiştir. Presleme sonrası 90x40x12 mm3 ebatlarında kompozitler elde edilmiştir. Kompozit malzemeler tel erezyon tezgahında kesilmiş ve CNC torna tezgahında işlenerek aşınma numuneleri üretilmiştir. Yapılan çalışmalarla üretilen kompozit malzemelerin yoğunluk, gözeneklilik, sertlik, mikroyapı ve aşınma özellikleri incelenmiştir. Saf Al7075 alaşımının yoğunluğu kompozit malzemelere göre daha yüksek çıkmıştır. B4C ve Si3N4 oranlarının artması ile kompozitlerde gözenek miktarları artmıştır. %5 ve %10 B4C takviyeli kompozit malzemelerde parçacıklar mikroyapıda homojen dağılmıştır. En yüksek sertlik değeri Al7075/%15B4C/%2Si3N4 kompozit malzemesinde (110 HB) elde edilmiştir. En yüksek sürtünme katsayı değerleri ise saf Al7075 alaşımlarında belirlenmiştir. Numunelerin sertlik değerlerindeki artış ile sürtünme katsayısı değerleri düşmüştür. 
Anahtar Kelimeler:

Al7075, B4C, Si3N4, Mikroyapı, Aşınma

Production of Powder Metal Al7075/B4C/Si3N4 Composite Materials and Investigation of Wear Properties

In this study, Al7075 alloy, Al7075/B4C composite material and Al7075/B4C/Si3N4 composite materials were produced by powder metallurgy method. Prealloyed Al7075 powders were used as matrix material to produce composites. The powders whose mixing ratios were determined by weight were mixed in the 3D mixer for 15 minutes. The mixture powders were pre-heated in a preheated hot stamping mold at 450 °C for 30 minutes. 90x40x12 mm3 composites were obtained after pressing. Composite materials were cut at wire EDM (Electrical discharge machine) and CNC lathes were processed to produce wear samples. Density, porosity, hardness, microstructure and abrasion properties of composite materials produced by the studies were investigated. The density of Al7075 alloy was higher than the composites. Pore amount increased with increasing B4C and Si3N4 ratio. In 5% and 10% B4C reinforced composite materials, the particles were homogeneously distributed in microstructure. The highest hardness was observed in Al7075/15% B4C/2%Si3N4 composite material (110 HB). The highest coefficients of friction were found in the Al7075 alloy, which was not reinforced. 

___

  • Chawla, K. K. (2012). Composite materials: science and engineering. Springer Science & Business Media.
  • Gay, D. (2014). Composite materials: design and applications. CRC press.
  • Chawla, K. K. (2006). Metal matrix composites. Materials Science and Technology.
  • Kaczmar, J. W., Pietrzak, K., & Włosiński, W. (2000). The production and application of metal matrix composite materials. Journal of materials processing technology, 106(1-3), 58-67.
  • Pol, N., Verma, G., Pandey, R. P., & Shanmugasundaram, T. (2018). Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour. Defence Technology.
  • Bodunrin, M. O., Alaneme, K. K., & Chown, L. H. (2015). Aluminium matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics. Journal of materials research and technology, 4(4), 434-445.
  • Zhang, L. C., & Attar, H. (2016). Selective laser melting of titanium alloys and titanium matrix composites for biomedical applications: a review. Advanced Engineering Materials, 18(4), 463-475.
  • Yao, Y. T., Jiang, L., Fu, G. F., & Chen, L. Q. (2015). Wear behavior and mechanism of B4C reinforced Mg-matrix composites fabricated by metal-assisted pressureless infiltration technique. Transactions of Nonferrous Metals Society of China, 25(8), 2543-2548.
  • Mazzolani, F. M. (Ed.). (2014). Aluminium structural design (Vol. 443). Springer.
  • Torralba, J. D., Da Costa, C. E., & Velasco, F. (2003). P/M aluminum matrix composites: an overview. Journal of Materials Processing Technology, 133(1-2), 203-206.
  • Tajally, M., Huda, Z., & Masjuki, H. H. (2010). A comparative analysis of tensile and impact-toughness behavior of cold-worked and annealed 7075 aluminum alloy. International Journal of Impact Engineering, 37(4), 425-432.
  • Shorowordi, K. M., Laoui, T., Haseeb, A. S. M. A., Celis, J. P., & Froyen, L. (2003). Microstructure and interface characteristics of B4C, SiC and Al2O3 reinforced Al matrix composites: a comparative study. Journal of Materials Processing Technology, 142(3), 738-743.
  • Ma, Z. Y., Tjong, S. C., Li, Y. L., & Liang, Y. (1997). High temperature creep behavior of nanometric Si3N4 particulate reinforced aluminium composite. Materials Science and Engineering: A, 225(1-2), 125-134.
  • Abdul-Lattef, N. I., Ismail Khedar, A. R., & Goel, S. K. (1985). Preparation of Al-Al 2 O 3-MgO cast particulate composites using MgO coating technique. Journal of materials science letters, 4(4), 385-388.
  • Toptan, F., Kumdalı, F., & Kerti, I. (2006). Al-B4C kompozitlerinin fren diski olarak kullanılabilirliğine genel bir bakış. Metalurji, 145, 11-18.
  • Gromov, A. A., & Chukhlomina, L. N. (Eds.). (2015). Nitride Ceramics: Combustion Synthesis, Properties and Applications. John Wiley & Sons.
  • Surappa, M. K. (2003). Aluminium matrix composites: Challenges and opportunities. Sadhana, 28(1-2), 319-334.
  • Karabulut, Ş., Karakoç, H., & Çıtak, R. (2016). Influence of B4C particle reinforcement on mechanical and machining properties of Al6061/B4C composites. Composites Part B: Engineering, 101, 87-98.
  • Kumar, R., & Dhiman, S. (2013). A study of sliding wear behaviors of Al-7075 alloy and Al-7075 hybrid composite by response surface methodology analysis. Materials & Design, 50, 351-359.
  • Çinici, H., GÖKMEN, U., KIRMIZI, G., & ÇAMKERTEN, R. Sıcak Presleme Yöntemiyle Üretilmiş B4C Takviyeli AA 7xxx Matrisli Fonksiyonel Derecelendirilmiş Malzemelerin Çapraz Kırılma Dayanımının Belirlenmesi. Muş Alparslan Üniversitesi Fen Bilimleri Dergisi, 5(1), 383-386.
  • Ambigai, R., & Prabhu, S. (2017). Optimization of friction and wear behaviour of Al–Si3N4 nano composite and Al–Gr–Si3N4 hybrid composite under dry sliding conditions. Transactions of Nonferrous Metals Society of China, 27(5), 986-997.
  • Baradeswaran, A. E. P. A., & Perumal, A. E. (2013). Influence of B4C on the tribological and mechanical properties of Al 7075–B4C composites. Composites Part B: Engineering, 54, 146-152.
  • Sharma, P., Sharma, S., & Khanduja, D. (2015). Production and some properties of Si3N4 reinforced aluminium alloy composites. Journal of Asian Ceramic Societies, 3(3), 352-359.
  • Matik, U., & Tanattı, K. Sıcak Ekstrüze Edilmiş AA7075-Sicp Kompozitlerin Tribolojik Karakteristiklerine Isıl İşlemin Etkisi. Politeknik Dergisi, 20(4), 807-814.
  • Göde, C. (2011). TM ile üretilmiş Alumix-231 SiCp ve B4Cp kompozitlerin farklı üretim yöntemlerinin mekanik özelliklere etkisi.
  • Halil, A. R. I. K., & ORHUN, D. Z. Investigation of Dry Sliding Wear Behavior of Powder Metal (P/M) Materials Produced from Mixture of Fe-Cu-C Powders. Gazi University Journal of Science Part A: Engineering and Innovation, 5(1), 37-48.
  • Höganäs PM-school, “Sintered iron-based materials”, Page: 9-19, (2013).
  • Canakci, A., Arslan, F., & Varol, T. (2013). Effect of volume fraction and size of B4C particles on production and microstructure properties of B4C reinforced aluminium alloy composites. Materials Science and Technology, 29(8), 954-960.
  • Canakci, A., & Arslan, F. (2012). Abrasive wear behaviour of B 4 C particle reinforced Al2024 MMCs. The International Journal of Advanced Manufacturing Technology, 63(5-8), 785-795.
  • Zorzi, J. E., Perottoni, C. A., & Da Jornada, J. A. H. (2005). Hardness and wear resistance of B4C ceramics prepared with several additives. Materials Letters, 59(23), 2932-2935.