Tabla tipi kavelalı köşe birleştirmelerde tutkal çeşidinin çekme direncine etkileri

Bu çalışmada tabla tipi mobilya üretiminde uygulanan kavelalı köşe birleştirmelerde tutkal çeşidinin çekme direncine etkileri araştırılmıştır. Deney örnekleri yonga levha ve lif levhadan hazırlanmıştır. Deney örneklerinin kenarları Doğu kayını ile masiflenmiştir. Masifleme işlemlerinde ve kavelalı köşe birleştirme işlemlerinde Polivinilasetat, Polimarin (Desmodur-VTKA), Klebit 303 olmak üzere üç çeşit tutkal kullanılmıştır. Toplam 72 adet deney örneği ISO 6237'de belirtilen esaslara göre çekme direnci deneyine tabi tutulmuştur. Deneyler sonucunda; lif levhalar, yonga levhalara üstünlük sağlamıştır. Tutkallar içinde en iyi sonucu PVAc tutkalı vermiştir. Tutkal çeşidi ve levha türü interreaksiyonu ise istatistiksel anlamda önemsiz çıkmıştır.

Effect of glue type on tensile strength for case construction with dowel corner joints

In this study, it has been searched the effects of glue type on tensile strength for case construction with dowel corner joints. Specimens were prepared from particleboard and fiberboard. The edges of the specimens were stuck with beech wood. Poljyinilacetat, Polimarin (Desmodur-VTKA), Klebit 303 adhesives were used as glue on the edge stick procedure and dowel joints. According to the principles of ISO 6237 total 72 speciments have been tested under static load in the test. As the results of the tests; it was determined that fiberboard is better than particleboard. PVAc glue was given the best result in all adhesives. The interreaction of glue type and kind of board has not been important by statisticaly.

___

  • 1. Örs Y.,Efe H., 1998, Mobilya (Çerçeve Konstrüksiyon) Tasarımında Bağlantı Elemanlarının Mekanik Davranış Özelliklen Doğa. Tr. of Agriculture and Foresty 22-5,21-27 .
  • 2. Şafak, R., 2000, Kutu Konstrüksiyonlu Mobilya Köşe Birleştirmelerinde Mekanik Özellikler, G. Ü Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, Ankara.
  • 3. Efe H., 1992, Mobilya Endüstrisinde Kullanılan Ahşap Levhaların Soket-Vida Tutma Yetenekleri ORENKO 93. 2. Ulusal Orman Ürünleri Endüstrisi Kongresi 6-9 Ekim 1993 Bildiri Metinleri S:319-339 K.T.Ü Orman Fakültesi, Trabzon .
  • 4. Özçiftçi, A., Dündar, K., Özen, R., 1996, Kutu Mobilyada Bazı Köşe Birleştirmelerin Mukavemet Özelliklerinin Teknik Olarak Hesaplanması, Journal of Scientific Research Foundation, Science and Engineering Volume I, No: 2, s: 71 İlmi Araştırmalar Vakfı, İstanbul.
  • 5 Zhang H.L.,Eckelman C.A. Rational Design of Multi-Dowel Corner Joints in Case Construction Forest Products Journal Vol:43 (11/12) 52-58 1993, USA.
  • 6. Özçifçi A., 1995, Yonga Levha ile Hazırlanan Mobilya Köşe Birleştirmelerine ait Mukavemet Özelliklerinin Araştırılması, G.Ü. Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, Ankara .
  • 7. Efe H., 1998, Kutu Konstrüksiyonlu Mobilya Köşe Birleştirmelerinde Rasyonel Kavela Tasarımı, Politeknik Dergisi, Cilt: 1, Sayı: 1-2, s: 41-54 .
  • 8. Wan-Qian Liu, Ekelman C. A .Effec Of Number Of Fastener On The Strength Of Corner Joints For Cases, Forest Products Journal, 4.8 (1): 93-95 USA.
  • 9. Redding, R., Fachstufe Holztechnik Technologie, Verlag Handwerk und Technik G.m.b.H., Lademannbogeu 135, 2000 Hamburg 63, 1984, s: 98-99.
  • 10. Ping, C. L., HU, W.F., Study on the Strength of "Moltingject" Corner Joints of Furnuture, Forest Products Dept. Northeast Forestry Universty, Harbin 150040, China. Holz als Roh-und Werkstoff, 1995, 53, 6, 385-388 .
  • 11. Ching, S.W., Yiren, W., A Study on Bending Moment Resistance of Particleboard Corner Joint in Carcass Furniture, Department of Forest Products Industry, Notional Chia-Yi Institute of Agriculture Taiwan Forest Products Industries 1994', 13, 4, 600-610.
  • 12. Zhang H.L., Eckelman C.A. The Bending Moment Resistance of Single Dowel Corner Joints in Case Construction, Forest Products Journal Vol:43, No:6, Pg. 19-24 1993, USA.
  • 13. Pfingsten, O. H., Techinsches Zeichnen fur Hohberufe, Sxhrocdel Schulbuchverlag Gmbh, Hannover, 1985, s : 51 -71.
  • 14. Şanıvar N., Zorlu İ., 1980 Ağaç İşleri Gereç Bilgisi, Milli Eğitim Basımevi, 303, İstanbul.
  • 15. TS 4539 Ahşap Birleştirmeler, TSE, Ankara .
  • 16. Burdurlu, E., 1994, Ahşap Kökenli Kaplama ve Levha Üretim - Kullanım Teknolojisi, Bizim Büro Basımevi, Ankara
  • 17. TS 3891, 1983, Yapıştırıcılar - Polivinilasetat emilsiyon, T. S. E. , Ankara
  • 18. Polisan, 1996, Üretici Firma, Bolu .
  • 19. Örs, Y., Atar, M., Özçiftçi, A., 1997, Bonding Strength of PVAc and Based on Polyürethane Adhesives in Some Wood Materials Treated with Impreynation, Journal of Agriculture and Forestry (Printed ), Ankara, Turkey .
  • 20. TS 2471, 1976 Odunda Fiziksel ve Mekanik Deneyler İçin Rutubet Miktarının Tayini, TSE, Ankara .
  • 21. ISO 6237/DIS 1987 Adhesives-Wood to Adhesive Bonds Determination of Shear Strength by Tensile Loading .
  • 22. Efe H., 1999, Kutu Konstrüksiyonlu Mobilyada Sabit (Yabancı Çıtalı) ve Demonte (Trapez) Köşe Birleştirmelerin Çekme ve Basma Dirençleri, Politeknik Dergisi, Cilt: 2, Sayı: 4, s: 43-51.