Kutu konstrüksiyonlu vidalı mobilya köşe birleştirmelerin çekme direnci

Çalışmada, kutu konstrüksiyonlu, tutkalsız ve tutkallı vidalı mobilya köşe birleştirmelerde çekme dirençlerinin karşılaştırılması amaçlanmıştır. Bu maksatla, sentetik reçinelerle kaplanmış yonga levha (Suntalam) ile lif levha (MDF Lam), birleştirme işlemlerinde, 4x50 ve 5x60 olmak üzere iki tip vida kullanılmıştır. Tutkallı birleştirmelerde poliüretan esaslı desmodur-VTKA tutkalı kullanılmıştır. ASTM D 143-83 esaslarına uyularak yapılan deneyler sonucunda; MDF Lam ve 4x 50 vidalar daha başarılı bulunmuştur.

The tensile strength of screw joints on furniture corner joints for case construction

In this study, it was aimed to compare the tensile strength of without glue and glued screw joints on furniture corner joints for case construction. For this purpose, the specimens were prepared of particleboard and medium density flberboard surfaced with synthetic resin sheet, in the connection process, two types screw which were measured 4 x50 and 5 x60 were used. In the glued joints, polyuretan based desmodur-VTKA adhesive was used. As a results of the tests which have been tested according to the principles of ASTM D 143-83; it has been obtained that the medium density flberboard surfaced with synthetic resin sheet and 4x50 screws were more succesful than the others.

___

  • 1. Efe, H., Mobilya Endüstrisinde Kullanılan Soket-Vidanın Mukavemet Özellikleri, K.T.Ü. Orman Fakültesi, ORENKO 93, II. Ulusal Orman Ürünleri Kongresi, Bildiri Metinleri, s: 319-339, Trabzon, 1993.
  • 2. Örs, Y., Efe, H., Mobilya (Çerçeve Konstrüksiyon) Tasarımında Bağlantı Elemanlarının Mekanik Davranış Özellikleri, Tr. J. of Agriculture and Forestry, Vol: 22, s: 21 – 27, TÜBİTAK, 1998.
  • 3. Eckelman, C. A., Which Screw Holds Best ?, Furniture Design and Manufacturing Magazine, September, 1974.
  • 4. Efe, H., Mobilya Endüstrisinde Kullanılan Ahşap Levhaların Soket – Vida Tutma Yetenekleri, G. Ü. Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, Ankara, 1992.
  • 5. Zhang, J. L., and Eckelman, C. A., The Bending Moment Resistance of Single – Dowel Corner Joints in Case Construction, Forest Product Journal, Vol: 43, No: 6, p: 19 – 24, 1993.
  • 6. Zhang, J. L. and Eckelman, C. A., Rational Design of Multi – Dowel Corner Joints in Case Construction, Forest Product Journal, Vol: 43, No: 11/12, p: 52 – 58, 1993.
  • 7. Efe, H., Kutu Konstrüksiyonlu Mobilya Köşe Birleştirmelerinde Rasyonel Kavela Tasarımı, G. Ü. T. E. F. , Politeknik Dergisi, Cilt: 1, Sayı: 1-2, s: 41-54, 1998.
  • 8. Eckelman, C. A., Designing High Quality Furniture With Wood Composites, Purdue University Paper, p: 42 – 47, 1999.
  • 9. Efe, H. ve Kasal, A., Kutu Konstrüksiyonlu Sabit ve Demonte Köşe Birleştirmelerde Çekme Direnci, G.Ü., Endüstriyel Sanatlar Eğitim Fakültesi Dergisi, Yıl: 8, Sayı: 8, s: 61 - 74, 2000.
  • 10. Efe, H. ve Kasal, A., Tabla Tipi Kavelalı Köşe Birleştirmelerde Tutkal Çeşidinin Çekme Direncine Etkileri, G. Ü. T. E. F., Politeknik Dergisi, Cilt: 3, Sayı: 4, s: 67-72, 2000.
  • 11. Efe, H. ve Kasal, A., Tabla Tipi Mobilya Köşe Birleştirmelerinde Eğilme Direnci Özellikleri, Z.K.Ü. Karabük Teknik Eğitim Fakültesi, Teknoloji Dergisi, Yıl: 3, Sayı:4, s: 33 – 45, 2000.
  • 12. Özçifçi A., Yonga Levha ile Hazırlanan Mobilya Köşe Birleştirmelerine ait Mukavemet Özelliklerinin Araştırılması, G.Ü. Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, Ankara, 1995.
  • 13. Wan-Qian Liu, Ekelman C. A. Effect of Number of Fastener on The Strength of Corner Joints for Cases, Forest Products Journal, Vol: 48, No: 1, p: 93 – 95, 1993.
  • 14. Ping, C. L., Hu, W.F., Study on the Strength of “Moltingject” Corner Joints of Furnuture, Forest Products Dept. Northeast Forestry Universty, Harbin 150040, China. Holz als Roh-und Werkstoff, Vol: 53, No: 6, p: 385 - 388, 1995.
  • 15. Ching, S.W., Yiren, W., A Study on Bending Moment Resistance of Particleboard Corner Joint in Carcass Furniture, Department of Forest Products Industry, Notional Chia-Yi Institute of Agriculture Taiwan Forest Products Industries, Vol: 13,No: 4, p: 600-610, 1994.
  • 16. Pfingsten, O.H., Techinsches Zeichnen für Hohberufe, Sxhrocdel Schulbuchverlag Gmbh, Hannover, s : 51 – 71, 1985.
  • 17. Özçifçi, A., Altınok, M., Özen, R., Kutu Mobilyada Bazı Köşe Birleştirmelerin Mukave-met Özelliklerine Ait Deneysel Sonuçların İstatistiksel Analizi ve Değerlendirilmesi, Journal of Scientific Research Foundation, Vol: 1, No:2, p: 63 – 70, 1996.
  • 18. TS 1770, Odunlifi ve Yonga Levhaları (Sentetik Reçinelerle Kaplanmış), T.S.E., Ankara, 1974.
  • 19. Polisan, Üretici Firma, Bolu, 1996.
  • 20. TS 61, Ağaç Vidaları, T.S.E. , Ankara, 1978.
  • 21. TS 2471, Odunda Fiziksel ve Mekanik Deneyler İçin Rutubet Miktarının Tayini, T.S.E., Ankara, 1976.
  • 22. ASTM - D 143-83, Standart Methods of Testing Small Clear Speciments, 1983.
  • 23. Tekin, A., Bazı Ağaç Türlerinde Temel Makinalar ile Açılmış Zıvanaların Diyagonal Basınç ve Çekme Dirençlerinin Belirlenmesi, G.Ü. Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, Ankara, 1999.